Computer Support Forum

Can someone look at this STOP Blue Screen Error?

Question: Can someone look at this STOP Blue Screen Error?

STOP:0x0000007E(0xc0000005,0xFA9A73922,0xF9E49008,0xF9E48D08)
viadsk.sys-address F9A73922 Base at F9A72000, Datestamp 38eb04c7

Relevance 100%
Preferred Solution: Can someone look at this STOP Blue Screen Error?

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

Answer: Can someone look at this STOP Blue Screen Error?

16 more replies
Relevance 70.93%

Hello, I have an HP Pavilion g series laptop (running win7) that is in a continuous restarting loop. This happened after the computer auto updated (windows update). I do not know what was updated, but now every time the laptop starts up it seems to be in a continuous rebooting loop after the windows logo then a blue flash. I am unable to go into safe mode or any other mode as I keep getting redirected to a page that gives me two options:Launch Startup Repair or Start Windows Normally. Startup repair gives me the same results as trying to run in safe mode.

By turning the auto-restart on system failure off i was able to read what the blue error message, which says:
-

A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is your first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check you hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive curruption, and then restart your computer.

Technical information:
***STOP: 0X0000007B (0xFFFFF880009A9928,0xFFFFFFFFC000000D,0x0000000000000000,0X00000000000000000)

-
Can someone give me advice on how to solve and prevent this problem? I am currently using a different laptop to access this forum.
kodex

Answer:Help with blue screen auto reboot, Stop: 0x0000007B error screen

Bug Check 0x7B: INACCESSIBLE_BOOT_DEVICE

The INACCESSIBLE_BOOT_DEVICE bug check has a value of 0x0000007B. This bug check indicates that the Microsoft Windows operating system has lost access to the system partition during startup.





Quote:
Cause

The INACCESSIBLE_BOOT_DEVICE bug check frequently occurs because of a boot device failure. During I/O system initialization, the boot device driver might have failed to initialize the boot device (typically a hard disk). File system initialization might have failed because it did not recognize the data on the boot device. Also, repartitioning the system partition or installing a new SCSI adapter or disk controller might induce this error.

This error can also occur because of incompatible disk hardware. If the error occurred at the initial setup of the system, the system might have been installed on an unsupported disk or SCSI controller. Some controllers are supported only by drivers that are in the Windows Driver Library (WDL). (These drivers require the user to do a custom installation.)


Further Reading...
Bug Check 0x7B: INACCESSIBLE_BOOT_DEVICE

1 more replies
Relevance 70.52%

New to the thread.... not sure if i'm posting right, soo correct me if u want =)
Anyway.. yesterday I turned my computer on and got the screen "Sorry for the convenience blah blah blah... Start Windows Normally, Safe Mode...ect.
I chose Start Windows Normally, which did indeed start windows normally, but I wasn't sure what caused this problem in the first place, so i ignored it. I turned my computer off.

Later i turned my computer back on and was confronted by another screen, this time a Blue screen.. A Stop error, can't exactly remember the error, but said something about "memory dump'...
I eventually got avoided a problem with this screen and got into windows.. However this morning, when i turn the computer on, I was forced to use 'Last Known Good Configuration"

Whats going on? I did scans on Norton, Adaware & Spybot.

Please help!!

Answer:Blue Screen, Black Screen??? Stop Error Code?

Hi Kirstie, computers are great when they work huh? These stop errors and blue screens of death can have many causes. Sometimes they occur when a computer is getting older and some piece of hardware is going bad, like a memory stick for instance. Other times these errors occur after installing a new program or doing a windows update. They can be quite difficult to pin down sometimes as well. I would be glad to help you find the cause of the error if you will answer a few questions for me. By answering these questions I should be able to determine the cause and help you to correct it.

Here are some questions for you to answer that will help me. Just answer them the best you can and if you dont know an answer its ok. If you already answered anything I'm asking in your first post just skip over it.

1). What kind of computer do you have? Laptop? Desktop? Dell, HP, Ect?
2). Whats your level of experience? Novice, intermediate, expert, or dont know squat?
3). What operating system are you using? Xp Home or XP Pro?
4). What antivirus are you using? Are you using a firewall?
5) Please tell us a little about your computer. How old is your computer? What size Hard drive does it have?, processor, ram, Bios ver. Ect.
6). Do you have an Xp disk for this computer?
7). Does your computer have a floppy drive, CD drive, Ect.?
8). Do you have access to another working computer with an internet connection?
9). Did you noticed this problem occuring after installing anything recentl... Read more

9 more replies
Relevance 70.52%

Toshiba Satellite running on windows XP
When I start the computer, it asks if for the choice of Safe Mode, w/ Networking, w/Command Prompt or Normally.
I've tried them all and if I try it normally, it won't get past the XP loading screen. It's loading and then it flashes a blue screen for a second and then restarts the computer again.

I tried pressing F8 at boot and selected 'Disable automatic restart on system failure' and this is what I get
STOP: 0x00000024 (0x00190203, 0x83306788, 0xC0000102, 0x00000000)

I even tried using this http://forums.techguy.org/6669592-post28.html to get to chkdsk
At boot, F12, chose CD/DVD, but still nothing,
I even tried disabling boot from +HDD, FDD and LAN from the bios setup menu to see if it works and this is what I got, it just keeps going on and on unless I enable boot from +HDD
Intel UNDI, PXE-2.0 (build 082)
Copyright (C) 1997-2000 Intel Corporation

For Realtek RTL8139(X)/8130/810X PCI Fast Ethernet Controller v2.13 (020326)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM.


That's about everything I could get.
Thanks.
 

Answer:Can't start XP: After XP loading screen, Blue Screen Stop error

9 more replies
Relevance 70.11%

0x000008E 0x000001D,0xEB17166B,0xF1C51b28,0x00000000

address EB171568B base at EB1600F datestamp 448cd31


Eeeep! What does this mean and how do I fix it?!

Answer:Blue screen STOP error

when you got the blue screen was there any other info? usually near the bottom left of the screen there is a file name.

2 more replies
Relevance 70.11%

I tried to boot up my computer a couple of days ago and had a stop error. I have tried to do a recovery with the disks that came with my laptop, but with no success. Of course my laptop didn't come with the XP installation CD's so I can't even start a repair on the PC.

I tried to contact HP, but they were unable to help me. I hope someone here can help me more than HP was able to.

Thanks
 

Answer:XP Blue Screen Stop Error

7 more replies
Relevance 70.11%

I posted this thread before and was being helped by someone, but they didn't return after the initial day. Maybe I wasn't clear but anytime I try to boot back up, it goes straight into the blue screen. I am able to start in safe mode. They asked me to boot back up in safe mode and go to run and type in "SFC.EXE /SCANNOW". I did this but when I hit run or enter the run screen went away and nothing happened. So here is my original question.
I run windows xp. I was trying to download pictures on my computer from a disk that I made at a local drug store kodak kiosk when this started. I also found out a couple of days ago that a "friend" was surfing some really questionable sites. The computer was running fine until i put in this disk with pictures. I saved a few to the computer and then it blacked out and a blue screen came up with the following message. Also I tried turning it off and on a few times and it gets to the desktop and as soon as I try to go to the web or acess anything on the start menu, it goes right back to this blue page.

A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you have seen this stop error screen, restart your computer. If this screen apperars again, follow these steps
Check to be sure you have adequate disk space. If a drever is identified in the stop message, disable the driver or check with the manufacuter for driver updates. Try changing video ad... Read more

Answer:Blue Stop Error Screen

http://support.microsoft.com/kb/330182

28 more replies
Relevance 70.11%

First of all Hi.

I am not very computer savvy so any help is greatly apreciated.

I am getting a blue screen error on the start up of my laptop. This first occured while the laptop was running.
The error # is 0x0000007E (0xC0000005, 0x8A0C894c, 0xBACF78B4, OxBACF75B0). There is no other information on the blue screen.

I can start the computer in Safe mode, but not Safe Mode with networking.

The Laptop is a Dell with Intel(R) Core(TM) 2 CPU T5200 @1.60GHz
Running Windows XP professional, with service pack 3.

Will be checking thread repeatedly if you need any more information.

Answer:Blue Screen / STOP error

http://support.microsoft.com/kb/330182

Visiting the above link, a popup should appear download it and run the fix, if it doesnt work try following the steps on the page.

If you cant access the internet on your laptop simply download it elsewhere a.k.a a pc or something and use a cd or usb stick to transfer it to your laptop and use it in safe mode.

5 more replies
Relevance 70.11%

I had been using Picasa version 2.7 to edit and upload my photos to Picasa online. All was fine until I downloaded version 3.0 Beta. I now get a blue screen stop error. Uninstalling 3.0 and reinstalling 2.7 does not correct the problem. I then did a search of the word 'Picasa' on my computer and found about 30 files which were not removed by the uninstall so I manually deleted these files. I then reinstalled 2.7 again but no change. I did a virus and spyware scan and no help there either. The blue screen appears when Picasa does its scan of the computer for pictures and videos - at the end. The error message reads: Stop: 0x0000008E (0xC0000005, 0xA5ABCB2C, 0x00000000)

nv4_disp.dll - Address BF077755 base at BF012000, DateStamp 482dff70

I did the Dell self test diagnostics which turned up nothing.

Any help would be appreciated.

Answer:Blue Screen Stop Error

Try updating your video card drivers from HERE. It looks like the install has caused some corruption for you.

2 more replies
Relevance 70.11%

I am new to this forum and am not a computer geek, although I understand the basics of computing and can usually figure out a problem, sometimes needing help....as now.

I have an IBM R51 Think Pad with Windows XP.
My problem is that I loaded an HP Photosmart disk for a digital camera in my disk drive. The software did not download and I was not able to open my disk drive to remove the software. I managed to remove the entire drive from my laptop but was still not successful in removing the disk. When I booted my laptop (several attempts) a blue screen appeared telling me that I had a "stop error" which could be due to a hardware/software change. I was instructed to choose "last known good configuration (most recent settings that worked) but that only takes me to a blue screen stating: Technical information: **** STOP: 0x00000007f (0x00000008, 0x80042000, 0x00000000, ox00000000). I reinserted the disk drive in my laptop and after several attempts to log on a balloon informed me that Norton had detected a "backdoor" virus. I cannot go into safe mode. I can only go back and forth between the F8 window and the blue screen.

The blue screen also suggested: disable or remove any hardware or drivers; remove any newly installed software; restart computer in safe mode; run a system diagnostic utility (I do not have).

Can someone please help me get this straightened out or am I stuck with a fried laptop???? Thanks in advance for any assis... Read more

Answer:Stop Error Screen (Blue)

I don't quite understand what you were trying to download after loading the hp photosmart disk into your drive ! did the CD load the digital camera software or not? all CD/DVD drives have a pin hole on the face of the drive door cover that you can use to put a paper clip or needle into to push and manual eject the CD or DVD out ...so you can remove the disk. try that first.....then reboot to see if that makes a difference. also Do you have a XP CD to try to attempt a XP operating system repair...? a repair of your operating system will leave all your precious data files intact. or hopefully you are savvy enuf to have used an external harddrive to back them up via a usb port. post back with results and answers....

18 more replies
Relevance 70.11%

Hi,
This is for a gateway MX6448 Win XP. Tapped mouse when computer went into hibernate mode, then computer shut down and restarted with a blank screen then repeated to shut down and restart over and over. Went into bios F2 did nothing but exit and save. Restarted and it did the same thing. Went into F8 could not reboot into safe mode (did same thing) went into F10 chose to not automatically restart on system failure. Now reboots to blue screen with stop error: C0000221 bad image check sum. bad image gdi32.d77 is possibly corrupt the header does not match the computer check sum.

Please advise

Thank You so much
 

Answer:blue screen and stop error Please help!

16 more replies
Relevance 70.11%

I hope someone can help I have been looking ever where for an answer to this. Once in a while I get a BSOD it says
IRQL_NOT_LESS_OR_EQUAL
0X0000000A (0X00000000, 0X000000FF, 0X000000, 0X806E2EA0)

I am not to sure what to do about this. Also ever time I restart or shut down my computer just after I click either one I get
Stop Error: 0x000000C4 (0x00000060, 0x00000064, 0x00000000, 0x00000001)

I hope this is all the information that is needed. Thank you for any help.
 

Answer:Blue Screen Stop Error

16 more replies
Relevance 70.11%

Hi, been having trouble lately with wife's computer rebooting off and on by itself during web browsing or other things. Here's the latest that came up. I set it to not reboot when errors occurred, but this blue screen came up and wondered if any of you know what it is. One thing i done was to go to nVidia site and upgrade my video driver. It's a 32M nVidia GEForce MXDOR. It was rebooting on it's own before i upgraded too. Anyways here's error:

***Stop:0x0000008E(0x0000005,0xF838CB3B,0x4BD7720,0x00000000)

***NDIS>SYS-ADDressF838CB3B baeat F838c000,DateStamp 2367dc561

Beginning dump of physical memory
Physical memory dump complete

Contact your system administrator or tech support group for further assistance.

Thanks in advance for any help
Its win xp home
 

Answer:Stop Error Blue Screen

16 more replies
Relevance 70.11%

hello
This morning I was working on my computer first it started working slowly then I tried using my web browser (fire fox) came up error not enough resources are available. So restarted my computer then the blue screen hit me I tried safe mode. Tried all options from boot menu didn?t work so can anyone please help me

im doing now memtest86

More replies
Relevance 70.11%

I've been getting a Blue screen lately, it rarely repeats on reboot, but keeps coming back periodically.

Stop: 0x0000007E (0xC000001D, 0x806ECABD, 0xBA4C2DC0, 0xBA4C2ABC)

Nothing after that. In my experience I have seen bad Memory cause blue screens, so I removed one stick and still got the error, I then switched to my other stick and thought I had found it because It went a couple of days, then today it happened again. This system has been running flawlessly since I built it, about a year and a half ago. No recent hardware or software changes, I was about to install Windows 7, but hadn't gotten around to it yet.

I do have 2 slave Hard drives, I am currently unplugging them one at a time to see if it continues.

Does anyone have any idea what these numbers in the error mean? Would appreciate any help. My system is in my signature.

Thanks,
Rick

Answer:Help with Blue Screen Stop Error

Post a zipped copy of your Minidump files found in your Windows folder.

12 more replies
Relevance 70.11%

I am getting a stop error message 0x000000F4 I can't even get on Windows. I have a Dell Inspron 1525 with Windows Vista. I can't use safe mode or any of the modes. The hardware diagnostics check was clean. I tried start up repair from the OS disc with nothing. What can I do here
 

Answer:Stop Error Blue screen

How strange....I worked on a laptop last night with the same issue. In fact, it was the same exact laptop.
When I did the Dell Diagnostics tests, it came back with a failed hard drive. But yours passed?
One thing I did read about that error message that I did not try was checking the CMOS battery.
Try popping out the battery, wait 30-60 seconds, and putting it back in.
Otherwise, I would still suspect a failing hard drive.
 

2 more replies
Relevance 70.11%

I was referred here by a helper in Spybot Search & Destroy. I ran my logs and posted for him, he recommends that someone here at this forum take a look at my logs to decipher if my problems is caused by software vs. hardware. I waited 4 days for his response. Now my computer is really slow. I've had to run in safe mode a few times.

Can someone assist me, thanks in advance. This is my first experience with a blue screen stop error.

Here is the error code:
BCCode:9c BCP1: 00000000 BCP2: 8054E5F0 BCP3: A2000000 BCP4: 84010400 OSVer:5_1_2600 SP:3_0 Product:256_1

Here is the logs on 1/22/2011.

DS (Ver_10-12-12.02) - NTFSx86
Run by Iovo & Christina at 18:57:55.10 on Sat 01/22/2011
Internet Explorer: 8.0.6001.18702
Microsoft Windows XP Professional 5.1.2600.3.1252.1.1033.18.894.294 [GMT -10:00]

FW: ZoneAlarm Firewall *Enabled*

============== Running Processes ===============

C:\WINDOWS\system32\Ati2evxx.exe
C:\WINDOWS\system32\svchost -k DcomLaunch
svchost.exe
C:\WINDOWS\System32\svchost.exe -k netsvcs
svchost.exe
svchost.exe
C:\WINDOWS\system32\ZoneLabs\vsmon.exe
C:\WINDOWS\system32\spoolsv.exe
svchost.exe
C:\WINDOWS\system32\agrsmsvc.exe
C:\Program Files\Common Files\Apple\Mobile Device Support\bin\AppleMobileDeviceService.exe
C:\Program Files\Bonjour\mDNSResponder.exe
C:\Program Files\Symantec_Client_Security\Symantec AntiVirus\DefWatch.exe
C:\WINDOWS\eHome\ehRecvr.exe
C:\WINDOWS\eHome\ehSched.exe
C:\Program Files\Java\jre6\bin\jqs.exe
C:\Program Files\Goog... Read more

More replies
Relevance 70.11%

I have a Dell Dimension 4700, 2560 RAM, 160GB HD OS-WIN XP Home.Recently got the Blue SOD screen on Booting up. I used the Dell diagnostics CD to do tests, & it listed 2 errors relating to th HD. I suspected a HD failure, as it is over 5yrs old. I bought a simmilar replacement - a Seagate Barracuda 7200-12, 500GB. Now when i try to re-install Win XP it starts of OK, but when it reaches the point where the T&C acceptance should appear, I get this erroe -STOP C0000221 Windows unknown hard error/system root/system32/NTDLL.LL. I have attempted loading WINS with an alternat CD, but I get a simmilar reaction, it gets to the FORMAT stage & then just stops without any errors.

Answer:Blue screen STOP error

Does the drive have jumpers on back for switching between 1.5 and 3.0 Gigabits/sec?   If your motherboard does not support the 3 Gigabit standard you might have some trouble with it and you'll need to set the jumper configuration to the 1.5 setting...   Look on the label on the SATA drive itself, to determine the jumper pin setup...   DON'T USE BOTH 1.5 and 3.0 AT THE SAME TIME.

14 more replies
Relevance 70.11%

I have been attempting to run a virus scan in Windows XP with 2different viurus programs. About half way through the scan, it hangs and i have to take the battery off to re-start and when it boot up a blue screen comes up andstates "A problem has been detected and Windows has shut down toprevent damage to your computer. Check to be sure you have adequate disk space.If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates.Try changing video adapters.Check with your hardware vendor for any BIOS upadates.Disable BIos memory options such as caching or shadowing.if you need to use safe mode to remove opr disable components, restart your computer, press f8 to select advanced start-up options, and then select safe mode.technical information: Stop: 0x0000008E (0xC0000005, 0xBF803E1A, 0xF6C527c4 , 0x00000000) win32k.sys - address BF803E1A base at BF800000, Datestamp 41107f7aplease help me......im not an expert on computer......

Answer:blue screen stop error

Hi,first go to the start button left hand bottom then click on the run icon when box appears type in chkdsk /r dont forget the space in between a box will appear and will run it or ask if you want to run it next time it starts click y for yes,restart pc chkdsk will start.Next download memtest from hereclick hererun it to check pc memory.

3 more replies
Relevance 70.11%

I have gotten this screen a few times before but thought nothing of it bcz I could get back online after shutting down. Its gotten to a point where its bothering me now. It always states the same thing... There was an error with your new hardware, we need to shutdown, sorry for the inconvenience, etc etc... then it gives me a few error numbers... this first error number was the main one... then the others... came up exactly like it is here
0x000000D1 (0xF8F32CB8, 0x00000002, 0x00000000, 0xF8EE0CE0) Please help!
Ice
 

Answer:Blue Stop Error Screen!!! ?????

11 more replies
Relevance 70.11%

I need help with an error I've been getting every so often. I spent the last few weeks dealing with HJT logs and combofix trying to find the problem. The topic has been closed, because my registry is clean and my virus software isn't finding any viruses. I've been told to turn off my automatic restart so I can get the information from the blue screen. I've done that and it is a (I think) Stop Error. The top of the page says a problem has been detected and so on. It has KERNEL_DATA_INPAGE_ERROR. It says some other generic problem solving steps that don't really work like checking for installation of any new hardware and software. It talks about disabling some of the BIOS memory options such as caching and shadowing. I have not done that only because I don't know what it will do. I know how to do it, just not what it will do or the purpose. Then it says Technical Information:
*** STOP: 0x0000007A (0xc03dd7ac, 0xc000000e, 0xf75eb130, 0x137c5860)
*** atapi.sys - Address F75eb130 base at f75da000, DateStamp 41107b4d

Beginning dump of physical memory
Physical memory dump complete
Contact your system administrator or technical support groupfor further assistance.

I apologize for how long this is but I wanted to get all the important inforation down incase any of it was important. Any help on how to fix this problem would be greatly appreciated. Thank you very much.

Answer:Stop Error/blue Screen

Try this: http://www.annoyances.org/exec/forum/winxp/1106266732

1 more replies
Relevance 70.11%

Hello,
Every 1-3 weeks I seem to be getting the same error, my screen flashes into a blue screen error and shuts down my computer, this happens out of the blue and is very unpredictable. I have written down the full error displayed, it says:

A problem has been detected and windows has been shut down to prevent damage
to your computer.

If this is the first time you've seen this stop error screen, restart your computer.
If this screen appears again follow these steps:

check to be sure you have adequate disk space, if a driver is identified in the stop
message, disable the driver or check with the manufacterer for driver updates, try
changing video adapters.

Check your hardware vendor for any BIOS updates, disable BIOS memory options
such as caching or shadowing, if you need to use safe mode to remove or disable
components restart your computer. press F8 to select advanced startup options,
then select safe mode.

Technical information:

*** STOP: 0x0000008E (0xC0000005, 0x9D1243A0, 0xD4DBEAE0, 0x00000000)

* Ti win32k.sys - Address 9D1243A0 base at 9D090000, Date stamp 4f2aa8Bc

Collecting date for crash dump
initialising disk for crash dump
Beginning dump of physical memory
Dumping physical memory to disk: 100
Physical dump complete

Contact your system admin or technical support group for further assistance.

If someone could please help me with this problem i would be very greatful!
 

Answer:Blue Stop Error Screen

that can be caused by a virus
follow advice here and post the logs those programs make

once I see the logs I can determine if it needs moving to malware or whether it is more likely to be other software/hardware causing it
 

1 more replies
Relevance 70.11%

I've been getting this Blue Screen that tells me to re-start my computer and it's frustrating me because I'm not sure why it keeps happening.

The blue screen says:

STOP: 0x0000008E (0xC0000005, 0x8054B0BA, 0xB2AC55EC, 0x00000000)

I have no clue what it means or why it's happening. It suggests I disable BIOS updates and says that a physical memory dump is occurring. I haven't downloading new drivers or anything (which is the suggestion Windows makes when I re-start the computer). I also have more then enough disk space so that shouldn't be an issue. Can anyone help?

I also may have part of the above stop error message wrong because I scribble it on a post-it. I can get a more detailed one if that helps. Thanks in advance because any help would be appreciated!!!!
 

Answer:Blue Screen - Stop Error

13 more replies
Relevance 70.11%

I have experienced windows reboots due to stop error like 000000c2 or 100008e. First I have reinstalled windows and all the adjacent software, but it seems the problem keeps on hitting me again. Last week I have connected my notebook to internet and since then I have had two windows suddenly reboots. I don't think it's a virus 'cause I'm running Kaspersky, with a Sygate firewall and a Ad-Aware real time protection spyware shield. Could you please give me an advice regarding these issues.

Answer:Blue Screen Stop error

Hi

Believe me; it?s very hard to say what?s wrong.
Usually the Blue screen error occurs because of a hardware fault or/and serious software malfunction. If this error occurs after the completely clear installation so I assume that it?s a hardware fault. Maybe memory module faults. But to be 100% sure you should check it. I think the best way is to contact the service.

2 more replies
Relevance 70.11%

All of a sudden I've been getting this blue screen every so often the last few weeks. It's a STOP: 0x0000009c(0x00000002, 0x8054D570, 0xF6002000, 0x0000017)"MACHINE_CHECK_EXCEPTION". I can go an extended amount of time and have nothing happen and then all of a sudden it can come out of nowhere. I believe it has something to do with hardware, but I have no clue where to begin.
 

Answer:Blue Screen Stop Error

Start > Run > eventvwr.msc > copy and paste some of the recent errors

also ...

navigate to C:\windows\minidump
Zip some of the recent minidumps and attach them here
 

1 more replies
Relevance 70.11%

Hello, I have turned on my PC and flit has brought me to a blhe screen with the following error
"A problem has been detected and windows has been shut down to prevent damage to yoyr computer.
If this the first time you've seen thjs stop erroer screen, restart your computer. If this screen appears again, follow these steps:
Disable or uninstall any anti virus, disk de fragmentation or backup utilities. Check your hard disk configuration, and checkfor any uupdated drivers. Run CHDSK /f to check for hard drive ccorruption, and then restart tlyour computer.

Technical support:
*** STOP: 0x00000024 (0x00190203, 0x8aad1c78, 0xc0000102, 0x00000000)

I need help and dont know what to do, I dont have the sindows xp instalation disc and cant go past this screen
Please help my only working pc

Answer:Blue screen STOP error help

Sorry, but this is a Windows 7 forum.

2 more replies
Relevance 70.11%

Hey everyone!

I need some help!

Here's the situation.

I have 2 identical dell laptops (exact same hardware profile and software deployment)

For Purposes of illustration I'll refer to them as A and B.


Laptop A came to my desk this morning with a stop error "PAGE_FAULT_IN_NON_PAGED_AREA" pretty typical BSOD.

So I pull the hard drive and put it in laptop B it works flawlessly which rules out the drive/software being the problem.

I then take the hard drive that just came out of laptop B and install it in laptop A.

Now both are working flawlessly which rules out the hardware in laptop A.

Thinking what ever the problem is may have worked itself out I put the drives back in their respective laptops and again got the stop error in laptop A.

As a side note both laptops boot far enough to get to the login in screen, it's when you log into the domain after it authenticates the users credentials that the page fault error occurs.

Any advanced knowledge in this matter would be appreciated.

Thank you!

Answer:Blue Screen Stop Error

Questions..

What model laptops are they? Also, which OS are they running?

And..does the stop error occur during every boot? Or is it just most of the time?

When you installed Laptop A's Hard-Drive into Laptop B, did the chkdsk utility launch at start-up?

3 more replies
Relevance 70.11%

I've been trolling through this website and many others to find the exact nature of my problem but I haven't come across any. From what I gather my problem can fall under many many different hardware/software problems but I am just going to go ahead and ask your advice anyway.

When I blue screen I get the following message

STOP: 0x0000009C (0x0000000000000003, 0xFFFFF880026D4B30, 0x00000000B6200000, 0x000000000002010A)

Now I have consulted with family members who are more switched on when it comes to the finer details of computing and they suggest that it is faulty RAM. Which I am inclined to believe as the blue screen occurs when I am running RAM intensive applications (Java based game (Minecraft)), it usually happens around the 65% mark. I've also taken Google's own advice of updating all system drivers. Everything is up to date.

Looking forward to your take on this.


Bucky
 

Answer:Stop error - blue screen

So check the memory using Memtest86
 

4 more replies
Relevance 70.11%

http://wer.microsoft.com/responses/....3.0?SGD=f7d24a35-17a4-4ab1-848d-ee6651bfacea

I get this, almost everytime i turn on my pc... that is, when I CAN turn the computer on.

Everytime I start up my computer, i am faced with the 'start windows normally', 'last known good configeration' and 'safe mode' options... *when i chose safe mode the computer is immediately restarted, and the same when I chose last good known configeration.
Sometimes I must restart my pc like 10-15 times, just to get it to the windows loading screen, where I finally see my homescreen, for about 30 seconds that it before it restarts.

Today I am using the same computer, it has so far restarted twice in the last hour, but i know when it restarts I may not be able to turn it on again =\

Anyway... sO i repeatedly chose F8 when my pc started up, and chose the setting 'Disable Automatic Restart on System Failure', and I was faced with a blue error screen

'The BIOS in this system is not fully APCI compiant. Please contact you system vendor or visit http://www.hardware-update.com' (this website didn't seem to work for me.
'You vender is not fully ACPI compliant'

In the past month or two, i have also been faced with other blue error screens

1). 'Win32k.sys - Address BF8937D8 base, BF00000, Datestamp 4cc6d692.

STOP: 0x0000008e (0xc0000005, 0x80637625, 0xb8217b08, 0x00000000)'

2). IRQL_NOT_LESS_OR_EQUAL

3). PAGE_FAULT_IN_NONPAGED_AREA
... Read more

More replies
Relevance 70.11%

I get this almost everyday, I even restored the laptop to how it was out of box and it keeps crashing... here is the error.

MULTIPLE_COMPLETE_REQUESTS

***STOP: 0x00000044
(0x862df368,0x00000D60, 0x00000000,0x00000000)
 

Answer:Blue Screen Stop Error...

10 more replies
Relevance 70.11%

I've got a case of the blues , I know this is isn't new news to anyone but the blue screen is not going away ,. I'm running a Compaq Armada E500 laptop with windows 2000. I've tried to clear the blue screen , F8 ,F12, i've tried to start up in safe mode and everything listed in the list of examples but nothing works. I switched hard drives from my other Laptop and it stared up no problem . how can i reboot the hard drive if i can't run in safe mode?

Any help with this matter would be great!
 

More replies
Relevance 70.11%

does this mean anything to anyone?IRQL_NOT_LESS_OR_EQUAL***STOP:0x0000000A(o0xA9F25224,0x00000002,0x00000000,0x804FD2F9)

Answer:blue screen stop error

Deends on your operating system...but its normally a driver error

10 more replies
Relevance 70.11%

I kept getting a stop: error message everytime I tried to reinstall windows on this computer I am working on. I figured it was just a hard drive issue, so I replaced it and now I am running into the same type of error. It is a blue screen with this information:

STOP: 0x0000007E (0xC0000005, 0xF7577D44, 0xF7ADCC5C, 0xF7ADC92C)
Ntsf.sys - Address F7577D44 base at F7572000, DateStamp 3d6de5c1

then it runs a physical memory dump, any ideas?

Answer:Blue Screen W/ Stop: Error

I notice you have an HJT log posted. Is this the same computer? If so, please follow only the instructions given to you by the HJT team member who takes your log.

Thanks,
rigel

4 more replies
Relevance 70.11%

hello all....

my boss at work asked me to take his home pc home with me and put WIndows XP Pro on it for him....he was previously running Win2K. After running the setup and doing the install, on reboot, when trying to log on, i get a stop error blue screen. The only technical info at the bottom is this :

STOP: 0x0000008E (0XC0000005,0X804F2906,0XF533176C,0X00000000)
Beginning dump of physical memory
Dumping physical memory to disk: xx

where xx is a slow counting upwards number, starting at 1, until eventually it resets itself and starts the problem over again.

I am able to boot into safe mode.

The computer in question is a Gateway with a Pentium 2 348mhz, with 384mb ram.

if anyone can help, PLEASE DO! i do not want to return my bosses computer to him inoperable!
 

More replies
Relevance 70.11%

I was removing SP3 due to a compapability issue when my laptop crashed. When it retarted I got the following...
I had a "Skipping Auto Check" - Fatal Error Stop: C000021a
The session manager initilazation system process terminated unexpectedly
with a status of 0xc000003a (0x00000000 0x00000000)
the system has shut down

I am running xp home and have tried retstarting in "safe", "Repair", "last good config" etc none work. Tried loading XP disk and set up but now says it cant find any hard drives!

Please help!!!!!!!
 

More replies
Relevance 70.11%

I have a Dell Dimension 2400 computer and I am running Windows XP. I've been getting a stop error message that reads:

A problem had been detected and windows had been shut down to prevent damage to your computer.
DRIVER_IRQL_NOT_LESS_OR_EQUAL
If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory option such as caching or shadowing. If you need to use safe mode to remove or disable components restart your computer, press F8 to select advanced start up options, and then select safe mode.
Tech info: STOP: 0X0000DI (OXF749A508).....Blah, blah, blah...
Beginning dump of physical memory.
Physical memory dump complete.
Contact system administrator or tech support.

I've tried to research this and it says that I should uninstall the incompatible hardware. How do I know which item is causing the problem? Is there some kind of test I can perform? I tried wiping the computer, but it still happens. Please help!!!
 

Answer:Stop Error Blue Screen

Look in C:\Windows\Minidump for crash dump files with a DMP extension. ZIP some recent ones (5-6) and post here as a ZIP or RAR file. Debug analysis of the files usually points to the problem.
 

2 more replies
Relevance 70.11%

I keep gettting a blue screen error when i open internet explorer or firefox.

The stop error is

Problem detected and windows has been shut sown to prevent damage to the computer

RQL_NOT_LESS_OR_EQUAL

Stop: 0x0000000A(0x00000002,0x0000000a,0x806E4A16)

The computer is a Dell Inspiron, i have tried removing software from the machine but i keeps happening.

Can anyone help me out, you help is greatly appreciated.

Thanks

Chris
 

Answer:Stop Error - blue screen

Typically, this error occurs when a driver uses an incorrect memory address. Other possible causes of this error are an incompatible device driver, a general hardware problem, and incompatible software.

http://support.microsoft.com/default.aspx?scid=kb;en-us;Q314063

Start by reinstalling the Video and motherboard drivers?
 

2 more replies
Relevance 70.11%

Hello,

This morning, I tried turning on my desktop on in the living room, and was greeted with a black screen. This screen told me that the computer was shut down improperly, and that I had the choice to run in safe mode, safe mode with command prompt, safe mode with networking, restart to last good known configuration, and start windows normally.

I've tried to use every single option, but all of them load the "Windows XP Loading" screen for a max of 4 seconds, and then goes to a blue screen. The blue screen says:

"A problem has been detected and Windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this Stop error screen, restart your computer. I this screen appears again, follow these steps:

Disable or uninstall any anti-virus, disk defragmentation or back up utilities. Check your hard drive configuration, and check for any updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

Technical informatoin:

***STOP: 0x00000024 (0X001902FE, 0XF78E63DC, 0XF78E60D8, 0X8A5B9805)"

Of course thinking the worst at first, I call my roomate asking him what the computer was doing this morning, and he told me it was acting weird. Long story short, I got him to admit he was looking at things he shouldn't have been on my computer, and somehow got a virus on it. He said it installed a windows security program, and icons with porn in their names showed up. He s... Read more

Answer:Blue Screen STOP error

You may need to do a "clean install" or "full recovery" so you should review your options for that before proceeding. Most Dells have a "recovery partition" for that. (I think the F11 boot menu brings that up)

-----------------------

There is one option here that I normally only recommend for resourceful and experienced users, however if you have no choice but a "clean install" it is worth a try.

Reinstalls (overinstalls) by the way, will not remove viral components.

USING THE RECOVERY CONSOLE TO ACCESS SYSTEM RESTORE
If you do not have an XP CD download rc.iso from Elvandil's post here: http://forums.techguy.org/windows-nt-2000-xp/561576-mom-exe.html#post4622868
Burn the .iso file to CD. With Nero or Roxio you should only need to "open" the file and it will start the burner's ISO burning program.

DeepBurner can also be used to burn ISO files, I recommend the “portable” version:

http://www.deepburner.com/?r=download
Once that is done, you need to boot with either that or the XP installation CD to the Recovery Console. You may need to ensure that the CD drive is the first boot drive in the BIOS setup if it just boots to the same screen. Setup is accessed by looking for the key to press on the first data you see on the screen -- often F2

Directions are given here:

http://attachments.techguy.org/attachment.php?attachmentid=62075

There are several things to note about this operation.

1 ... Read more

1 more replies
Relevance 69.7%

Hello,

I have a blue screen problem that i can't find a solution to!

I recently bought a new graphic card: Radeon all-in-wonder x1800xl. Installed it on a clean system (did a reformat before i installed).
The problem occurs after usually 30-60 minutes of gaming (so far with oblivion, black & white 2). The game freezes for about 30 sec and then goes into blue-screen mode.
The message is as follows:
Kernel-Data-inpage-error stop error screen
then there are a lot of numbers etc.
I have sometimes noticed a slight change in fan noise prior to freeze (speeding up)
After reebot everything's back to normal.

My system is relatively new (a year and a half or so), i have:
Windows XP pro SP2
Asus P5AD2 deluxe motherboard with integrated sound-card
Pentium 4ht, 3.4Ghz, 2GB ram.
all my drivers are up-to-date as far as i know. The ATI drivers are certainly up-to-date

I have run some fix-it-utilities diagnostics and found no error or the like.

I previously had an ATI Radeon 600 series card, on the same system. Never had a problem with HL2, Far Cry, or whatever

Any ideas?

Thanks in advance,

Zurzu
 

Answer:Blue screen: stop error screen when gaming

16 more replies
Relevance 69.7%

Hello: Today I received a blue screen stop error message. I was using my AOL software at the time it occurred. This is the second time it happened; the first time was about a month ago. Last time I upgraded the driver for my video card, and I thought that had taken care of it. I don't remember for sure, but I was probably using my AOL software when it happened last time also.

The message today included this information:

Technical Information:
*** STOP: 0x0000008E (0x0000001, 0xAFCAE925, oxA714438c, 0x00000000)
*** watchdog.sys - Address AFCAE925 base at AFCAE000, DateStamp 480254ab

The message from a month ago was slightly different. It included the following information:

Technical Information:
***STOP: 0x0000008E (0xE0000001, 0xB3ED1925, 0xA379D320, 0x00000000)
***watchdog.sys - Address B3ED1925 base at B3ED1000, DateStamp 480254ab

I restarted the computer without incident.

I'd appreciate any advice; thanks.

Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: Intel(R) Pentium(R) 4 CPU 3.00GHz, x86 Family 15 Model 4 Stepping 3
Processor Count: 2
RAM: 2046 Mb
Graphics Card: NVIDIA GeForce 9500 GT, 1024 Mb
Hard Drives: C: Total - 472772 MB, Free - 305508 MB; F: Total - 476937 MB, Free - 432155 MB;
Motherboard: Dell Inc. , 0X8582, , ..CN7082155U50BD.
Antivirus: McAfee Anti-Virus and Anti-Spyware, Updated: Yes, On-Demand Scanner: Enabled
 

Answer:Solved: blue screen STOP error screen

16 more replies
Relevance 69.7%

Hello,

I have a blue screen problem that i can't find a solution to!

I have seen a similar problem posted previously on this forum. But after reading it i think this is a different problem, so, here goes:

I recently bought a new graphic card: Radeon all-in-wonder x1800xl. Installed it on a clean system (did a reformat before i installed).
The problem occurs after usually 30-60 minutes of gaming (so far with oblivion, black & white 2). The game freezes for about 30 sec and then goes into blue-screen mode.
The message is as follows:
Kernel-Data-inpage-error stop error screen
then there are a lot of numbers etc.
I have sometimes noticed a slight change in fan noise prior to freeze (speeding up)
After reebot everything's back to normal.

My system is relatively new (a year and a half or so), i have:
Windows XP pro SP2
Asus P5AD2 deluxe motherboard with integrated sound-card
Pentium 4ht, 3.4Ghz, 2GB ram.
all my drivers are up-to-date as far as i know. The ATI drivers are certainly up-to-date

I have run some fix-it-utilities diagnostics and found no error or the like.

I previously had an ATI Radeon 600 series card, on the same system. Never had a problem with HL2, Far Cry, or whatever

Any ideas?

Thanks in advance,

Zurzu
 

Answer:Blue screen: stop error screen when gaming

6 more replies
Relevance 69.7%

WIN XP blue screen error 'stop 0x24' which I guess is a NTFS_File_System error.
I can not get past the blue screen to Windows in any safe mode. PC always goes back to blue screen no matter what I do.

I just rec'd 6 install CDs from Dell and but have them for 15 days, or I must pay for them [that doesn't seem right, but it is another story].

How can I fix this without losing all my hard drive data? Dell said run chkdsk /r, they didn't say how. I'm guessing I use the 'Operating System' disc to start-up the PC and then somehow type in chkdsk /r? Does a prompt just come up when booting from the CD?

Any help is greatly appreciated!

Answer:XP blue-screen error: stop 0x24

Take the disk out of this computer, put it in an external case and attach it to a working computer via USB cable. Then run chkdsk on this drive on the working computer. You can also back up your data on that computer before reinstalling the OS on this hard drive if that is needed.

3 more replies
Relevance 69.7%

Hi,  my son was downloading music the other day on our computer, he had installed a USB cord for his mp3 player to record it and after he finished, shut it down.  Yesterday, i tried to start it when i got home, and when it gets to the windows boot screen, in changes to a blue screen and says, STOP ERROR...you cannot access, you may have a virus.."  it then gives me a little instruction to fix, but each time i try to boot, even in safe mode, it keeps reverting to this blue screen before i can get to any antivirus applications or cursor..windows will not load for me to do anything even in safe...what can i do to restore my computer?  It's running Windows 2000, Pentium 3, 1999 model from Dell, deskpro.  ....thanks

Answer:Blue screen STOP error when booting

Post the exact STOP error code you're getting and any files mentioned on the blue screen.

2 more replies
Relevance 69.7%

Windows XP

This week I downloaded and installed AVG Anti-Virus (Free) and ZoneAlarm (Free) on my Dell desktop. When I turn on my PC I get the blue screen with the following error: ***STOP 0x0000007B (0XBA4C3524, 0XC0000034, 0X00000000, 0X00000000).

I'm unable to access safemode and don't know how to get pass the blue screen. I downloaded a fix to my memory stick but need directions on how to install.

Thanks in advance for help.
Barb
 

Answer:Stop error 0x0000007B on blue screen

do you have windows xp CD?
 

3 more replies
Relevance 69.7%

Hi there!

Can anyone help me troubleshoot a Stop 0x000000D1 error? I have a Dell desktop (with XP) that I rarely use and when I tried to use it today I got the dreaded blue screen. I've tried starting in Safe Mode but when I do I get a long list of multi(0)disk(0)rdisk(0)partition(2)\WINDOWS\system32\drivers\....... and I also can't get to a command prompt. Help! What do I do?

I'm not extremely literate when it comes to computer terms so I'm hoping someone can help me out in semi-simple terms.

Thanks in advance!
 

Answer:Help! Blue Screen - Stop 0x000000D1 Error

theres some info here http://kadaitcha.cx/xp/stop_error.html#0x000000D1
DO you have any recovery CDs for that desktop ? -

It may be you have a recovery partition, so you can reinstall back to factory condition - also may enable you to do a repait

TO restore to factor conditions
1. Turn on the computer.
2 When the Dell screen appears <Ctrl> and then press <F11>
3 Should open Dell PC Restore -Symantec - click Restore.

Another altermnative - see if you can boot UBUNTU
UBUNTU
It may be possible to boot from another Operating System
This will at least test the Hardware and also see if you can see the Harddrive and possibly get data off.

If you have another PC with a cdwriter and spare CD
goto http://www.ubuntu.com/ and download the ISO

full details are here http://www.howtogeek.com/howto/wind...backup-files-from-your-dead-windows-computer/

click on the image "download ubuntu"
Select a location
then begin download
Save the file onto your PC &#8211; remember where you saved it &#8211; so you can find it again to create the image bootable CD.

You do NOT copy the ISO file onto a CD - you have to use the ISO to create a bootable CD
The CD creator software you have on the PC may have an option to create an image from an ISO
If not - use this free program http://www.imgburn.com/

When the UBUNTU CD boots - you will see the following options
1) Try ubunto without any change to your computer
2) Install ubuntu
3) Check CD for defects
4) Test memory
... Read more

1 more replies
Relevance 69.7%

I have an Asus laptop with Windows 7 Home Premium. Last night it started having a problem where it cannot boot and gives the following error on a blue screen: "STOP: c0000135 The program can't start because %hs is missing from your computer. Try reinstalling the program to fix this problem."

I've found some threads linking this error to AVG, so I've already followed these directions: http://forums.avg.com/us-en/avg-forums?sec=thread&act=show&id=132999

However, I'm still unable to start the computer without receiving this error.

The computer has also attempted to run "Startup Repair" but it just says it "cannot repair this computer automatically."

Any ideas on where to start?
 

Answer:STOP: c0000135 (Blue screen error)

6 more replies
Relevance 69.7%

I uninstalled a program and upon re-start i received the above stop error stating Inaccessible_Boot_Device.
I have tried to boot in safe mode and all of the other F8 options. I got a Black Boot cd and when I tried to boot from the cd I got the A:/ prompt.
I dont know what to do

HELP
 

Answer:Blue screen Stop Error 0x0000007B

8 more replies
Relevance 69.7%

Hello! I turned my computer on this morning and I GOT this blue screen with this error code 0x000000ED ((0x84FA5D28, 0xC000009C, 0x00000000, 0x00000090).
I have tried starting it in safe mode, safe mode with networking, safe mode with command prompt, last known configuration, etc. And nothing has worked. The blue screen is on repeat. I have no idea what to do.
My computer is a Sony Vaio and it is a a VGN-CR120E.
I do not have any Sony system recovery discs and I do not have any Windows Vista discs. If anyone could help me out I would greatly appreciate it!

Thanks!
 

Answer:blue screen error STOP: 0x000000ED

I was researching how to fix this and I saw that I should try to put a windows recovery disk in an iso format and put it on a disk. My brother downloaded a windows recovery disk and put it on a usb. I got to the BIOS screen on my computer and changed the boot to boot to the USB first. The recovery started working but when I got the the system repair screen it was supposed to bring up the operating system that you wanted to fix. My operating system didn't show up and I couldn't search for it. Do you know if it isn't showing up because the recovery is on a usb and not a disk?

Thanks!
 

1 more replies
Relevance 69.7%

My PC is now frequently crashing to the blue screen with error message Stop:0x000000F4 with four further hex parameters.

I haven't installed any new hardware or software for at least a couple of weeks, as far as I know.

I am uploading the last minidump file. Can someone kindly analyse this and tell me what the problem is?

From Googling this error message, I see that it generally points to a hardware problem. Other users seem to have spent a lot of time switching drives, cables, memory sticks etc. I am hoping someone will be able to point to the specific problem!

Thanks to anyone that can help!

My details:
OS Version: Microsoft Windows XP Professional, Service Pack 2, 32 bit
Processor: AMD Sempron(tm) Processor LE-1250, x86 Family 15 Model 127 Stepping 2
Processor Count: 1
RAM: 895 Mb
Graphics Card: ATI Radeon 2100, 1 Mb
Hard Drives: C: Total - 55028 MB, Free - 33299 MB; D: Total - 82589 MB, Free - 64527 MB;
Motherboard: Acer, RS740DV, , 04XJ83300780
Antivirus: AVG Anti-Virus Free Edition 2011, Updated: Yes, On-Demand Scanner: Enabled
 

Answer:Blue Screen. Stop:0x000000F4 error

I carried out a restore to a restore point a week previously to when the problem occurred.

After that, it ran without the Blue Screen for several days until...

The computer told me that updates were ready for the computer, and I clicked to install them. And I immediately got a Blue Screen!

It seems that for ever onwards the computer will try to install an update that make it crash. Is there a way I can stop this?

Ideally I would like to solve the problem at source. Could anyone tell me what the minidump is saying?

Thank you
 

1 more replies
Relevance 69.7%

ok so my desktop computer got, what i think is a virus, it turned my back ground blue with red and whit letters it said something about it may ruin my life?? im not sure it wasnt there very long. but then i got the blue screen of death that said " A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this ...blah blah blah the error was : ***STOP: 0x0000008e ( 0xc0000005, 0x8224Acc7, 0x9952B91c, 0x00000000)
And at the bottom it said memory dump complete. every time i try to start it normaly i get this message. It works fine in safe mode...ive tried scanning it nothing comes up. Ive tried the system restore, because this has happened to my laptop and it worked but when i try i get the error: 0x80070057. Im still learning about computers ( hints my user name ) but im great at following dirctions..Please help
 

More replies
Relevance 69.7%

hey friends i got this blue screen error of death jst at the start of windows xp media center loading---stop:0x0000007e(0xc0000005,0xf887018e,0xf8918748,0xf8918444)..my hp pavilion dv2000 had been affected by many blue errors which were cured bt can sum1 help me through dis plzzzzz..panda av 2008 detected many spyware on my pc which i deleted...actually i have 2 windows..media center is now showing blue screen error..bt xp pro is running..so help me what can i do to get away from dis blue screen error............thnx in advancemy main problem is that i cant even open my windows..blue screen comes when windows starts..
 

Answer:blue screen error--stop:0x0000007e

problem isi cant even start windows in safe mode...i repaired using my xp media center by boot disk...which was going ok but in b\w installing windows procedure this error occurstop:0x0000007e (0xc0000005,0xf89c318e,0xf8a47740,0xf8a4743c)hpqkbfiltr.sys -addres f89c318e base at f89c0000,date stamp 46770333begining dump of physical memoryphysical memory dump completeso what should i do now with hpqkbfiltr.sys bcoz it is stopping me to repair xp media centeri installed kaspersky in my 2nd windows & it detected hpqkbfiltr.sys as keylogger bt no option to repair or delete it..so wat now guyz ..can anyone help -plzz
 

1 more replies
Relevance 69.7%

I've been intermittently getting blue screens with the stop error 0x00000124, which the internet told me is either a driver or hardware issue. I've run memtest for 5 passes on both sticks of RAM and there were no errors. I do overclock my CPU, but my system is water cooled and the temp is always stable. In addition when not overclocked I still will get a blue screen sometimes. Here are my specs.

OS - Windows 7
x64
Windows 7 (Custom Build)
Not OEM
1-2 years old
1 year. I re-install Windows every so often for tidiness.

CPU: Intel i7 2600k
Video Card: EVGA Nvidia GTX 570 Super Overclocked
Motherboard: Intel Gigabyte Z68X-UD3H-B3
Power Supply: Antec TruePower Quattro 850W

The zip with the jcgriff2 report is too big for the upload limit. So I uploaded it here: https://www.box.com/s/2o4000o3lb26qgysjnmp

Answer:Blue Screen with Stop Error 0x00000124

Please download MiniToolBox , save it to your desktop and run it.Checkmark the following checkboxes: List last 10 Event Viewer log List Installed Programs List Users, Partitions and Memory size.Click Go and paste the content into your next post.Also...please Publish a Snapshot using Speccy - http://www.bleepingcomputer.com/forums/topic323892.html/page__p__1797792#entry1797792 .Louis

5 more replies
Relevance 69.7%

Hi there
Can you help me. I have pentium 4 computer and windows xp. I have only had this computer a few months it was brand new. It keeps crashing and coming up with this stop error. The screen goes blue and I have to reboot to get it going again.
Microsoft error reply says it is caused by an unknown device driver. It happens at least 3 or 4 times a week.
Do you know how I can fix it?
Thankyou
 

Answer:blue screen stop error windows xp

7 more replies
Relevance 69.7%

my systems crashes upto 4 to 5 times a day, blue screen comes up stop error codes etc( BAD_POOL_HEADER ), then sometimes IRQL_NOT_LESS_OR_EQUAL. then send report comes back saying error caused by video device driver.

Answer:blue screen, stop error codes

which viseo driver do you have

5 more replies
Relevance 69.7%

Hi everyone. I have been getting the notorious blue screen of death lately. It is a stop error. I have no idea how to prevent my computer from hanging like this. It sometimes happens randomly but it also happens when I play Microsoft's Age of Empires III with the expansion. Can anyone please help me because I really don't want to reinstall Windows unless I absolutely have to.
 

Answer:Blue Screen of Death - Stop Error

9 more replies
Relevance 69.7%

Hi,I have a dell inspiron E1505 and I've had it for about two years.  A few weeks ago I left my computer on and when I got home from work I opened firefox and the screen turn blue and said:Stop 0x000000F4 (0x00000003, 0x871FE8E0, 0x871FEA54, 0x805C8C88)then:Beginning dump of physical memoryPhysical memory dump complete.I've tried restarting it many times and now on the mainscreen it won't let me log in because the computer freezes.  I tried starting it in safe mode and run anti-virus but a message appears that says the system administrator will not allow it, but I am the system administrator.Does anyone know what is wrong with my computer?

Answer:blue screen error Stop 0x000000F4

I would also like to let you know that I've tried a system restore and that doesn't work either.

3 more replies
Relevance 69.7%

My computer has the following specs :-

CPU: AMD SEMPERON 2400+ 333Mhz FSB
HARD DISC 80 GIG 7200 RPM
Motherboard : Asrock K7S41-GX333FSB & 400DDR
Memory : 1GB DDR Memory
Video Card : REAL 256 INTEGRATED 3D GRAPHICS GPU
DVD-RW : YES
Floppy : 1.44MB Floppy Drive
Network Card : 10/100 Fast Ethernet Network Controller
USB : 4X REAR USB, 2X FRONT USB PORTS
Sound Card : 5.1 3D audio processing unit (APU)
Case : ice box zorro gamer ATX Case w/450 WATT PS and Front USB Ports
Keyboard / Mouse : Ezkey Silver/black 10 Hot Key Button Mouse & Labtec Internet Keyboard
Speakers : Made by Trust
Operating System : Windows XP Pro with SP2 (Although this error happened before sp2 was installed)
Monitor: Digimate L-1715 17" TFT Monitor

I keep getting Stop 0x000000C5 error. I've tried taking the memory out, as i previously had a 256mb in too, I've tried installing Logitech Mouseware, i've tried re-installing Windows, i've tried getting updated drivers off the Motherboard website and i really am running out of ideas. It's only a month or so old!!! I've had a look on the Microsoft Support site and it suggested running Driver Verifier but this is only supposed to be for Windows 2000. Plus it's not very clear how to do this. Does anyone have an idea what i can do?
Does anyone know of a solution? Or failing that, how do i run driver verifier?
 

Answer:Stop 0x000000C5 Error Blue Screen

http://support.microsoft.com/?kbid=291810&sd=RMVP
 

2 more replies
Relevance 69.7%

Okay I am freaking out here, of course because I have pictures on my computer of my newborn that I am terrified of losing....my computer worked fine on Wed. when I used it last, then on Friday, my brother noticed a blue screen on it. So I went to see for myself. I powered down the computer and restarted, but still the same screen appeared. Here is the jist of what it says.

Windows has been shut down to prevent damage to your computer.

UNMOUNTABLE_BOOT_VOLUME

Then it talks about any new hardware/software or something, which I have not installed anything new on the computer. Except AVG Free cause my McAfee subscription had run out.

Then at the bottom there is Technical Info.
STOP: 0x000000ED (0x833E0E30, 0xC000009C, 0x00000000, 0x00000000)

Can anyone please help me!! Please tell me all is not lost!!
 

Answer:Blue Error Screen/Stop Message...HELP Please!

Check all your drivers to see if any need updating.

WINDOWS XP SHUTDOWN & RESTART TROUBLESHOOTING = aumha.org/win5/a/shtdwnxp.php

http://www.google.com/search?hl=en&q=0x000000ED&btnG=Google+Search

Description of the Windows XP Recovery Console = http://support.microsoft.com/default.aspx?scid=kb;EN-US;314058

http://www.techtips4u.com/kb/sw/SW00014.htm

http://support.microsoft.com/?kbid=297185&sd=RMVP

You might check your IDE cable to the hard drive to see if it came loose or went bad. Also check your Bios settings to see if the hard drive is being detected. You might also take you Cmos battery to RadioShack as get a new one of the same exact type.
http://aumha.org/win5/kbestop.php
http://www.techtips4u.com/kb/sw/SW00014.htm

http://www.computerhope.com/issues/ch000630.htm

http://support.microsoft.com/kb/555302

http://www.windowsreinstall.com/install/winxp/howto3/unmountable.htm

http://www.microsoft.com/technet/prodtechnol/winxppro/reskit/prmd_stp_woft.asp

http://support.microsoft.com/?kbid=315403&sd=RMVP

STOP 0x000000ED UNMOUNTABLE_BOOT_VOLUME" Error Message When You Restart Your Computer or Upgrade to Windows XP = http://support.microsoft.com/defaul...port/kb/articles/q297/1/85.asp&NoWebContent=1
http://www.google.com/search?hl=en&q=0X000000ED&btnG=Google+Search
http://www.google.com/search?source...GGLD:2004-39,GGLD:en&q=stop:0x0000000ed+error
 

1 more replies
Relevance 69.7%

I have received a Blue Screen Stop Error on my Toshiba Satellite 5200 Series laptop.

I could report it here, in full, if that would be helpful. However, it begins by telling me to restart the machine but the unit's Power button is not allowing me to switch it off.

What action should I take ?

Answer:Restarting After a Blue Screen Stop Error

Crikey ! Someone at another forum just told me to hold the button down for 5 seconds..... and it worked !

1 more replies
Relevance 69.7%

so i got my first BSOD on my hp pavilion dv7..i was able to repair it through the start-up repair option..however when i check the error report(after doing an online solution check via windows) under
'Control Panel\System and Security\Action Center\Message Details' it says i have a problem with the NVIDIA graphics driver. The computer has an AMD graphics card plus the intel integrated graphics. I don't understand the report.
how can i know what caused the BSOD?

Answer:blue screen of death-STOP error

Samjumbo, you haven't uploaded your msinfo32 file.

For a better interpretation, you need to upload your MSINFO32.nfo file.
Click on the start button
Type "msinfo32" (without quotes) in the search bar of the start menu, click the resulting link. It will open the System Information window.
File>Save. In the "File Name" filed, put "MSINFO32" (without Quote), give the save location to desktop, and click the "save" button.
Give the time for processing, it will save a .nfo file on your desktop.
Zip it, and upload it following the instruction.
Anyway, the crash dump you supplied points out symentec/norton products out and out.


Code:
fffff880`07fcd498 fffff880`04636a6dUnable to load image \??\C:\ProgramData\Norton\{0C55C096-0F1D-4F28-AAA2-85EF591126E7}\NIS_18.1.0.37\Definitions\BASHDefs\20120928.001\BHDrvx64.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for BHDrvx64.sys
*** ERROR: Module load completed but symbols could not be loaded for BHDrvx64.sys
BHDrvx64+0x6a6d
Again,

Code:
fffff880`07fcd560 fffff880`02ea39b0Unable to load image \??\C:\Windows\system32\Drivers\SYMEVENT64x86.SYS, Win32 error 0n2
*** WARNING: Unable to verify timestamp for SYMEVENT64x86.SYS
*** ERROR: Module load completed but symbols could not be loaded for SYMEVENT64x86.SYS
SYMEVENT64x86+0x269b0
And again,

Code:
fffff880`07fcd688 fffff880`02e72a91*** WARNING: Unable to verify timestamp for SYMNETS.SYS
*** ERROR: Module lo... Read more

2 more replies
Relevance 69.7%

Good day, I have a Gateway MX3562 Notebook w/ XP loaded. This was brought to me to fix as my brother could not get XP to load.

When I received it I started it, XP Black loading screen started and then timed out with the STOP BLUE SCREEN Error..

STOP COOOO139 Enter point not found Setuindowtext could not be loaded in the dinaomic Link Library user32.dll

At that time I I restated by F8 safemode, would boot to safemode then time out before anything loaded on desktop by once more the "Blue Screen Errors" after many attempts to rebot in both XP normally and F8 safe mode, I had 0 success..

I then booted to the Gateway Recovery CD and attempted to repair. when trying to copy files from Disk it timed out bluescreen error "not_equal_or_less" Also, note when trying to copy files from recovery disk there was MANY files that failed to copy with error " Failed To Copy Extracting Process".. I assumed this was a disc problem. I bought a Brand New Sealed recovery disc and the same errors.

At this time I bought a XP Pro ver of Windows. I deleted the current drive at time of installing and attempted to load XP Pro. It would 100% Format then go to copy file process and would not copy MANY files. I had the option told retry and or skip the file. I did both many times and end result was always a BLUE SCREEN error..

I was reaching, thinking (maybe) the WIN XP Pro disc was corrup so I bought a WIN XP Home disk. SAME PROBLEM!.. some of the files... Read more

Answer:STOP (blue screen error) Win XP does not load

Also, when useing Gateway recovery CD it tries to fix by copying files, when copy starts it gets LOTS of these errors "Problem in extracting process: File:WINDOWS\inf\infcache.1
 

49 more replies
Relevance 69.7%

Hello,
I got my computer almost a year ago and about a month ago it randomly shut down and I got a blue screen message, but it was my first time so I just restart my computer like it said. However, recently it started to get worse. Just today, I got a blue screen and a random shut down. The random shut downs happen a lot in the past month or so, but it just restarts and gives me an error message It kept shutting down and I either get a blue screen message or an unsolvable error message. I don't know what to do with it and nothing would help. I have AVG antivirus, Trend Micro Security programs such as Housecall, HiJackThis, and Browser Guard. All my virus scans and such shows that I don't have an virus, its all clear. So now I'm just confuse on whether or not I'm having virus or computer problems. In addition, I have Windows 7.

This is my blue screen message error: there are some things missing from it, but this is the basic idea. If my computer does it again, I try to get the technical information.

A problem has been detected and Windows has been shut down to prevent damage to your computer.

If this is the first time you’ve seen this Stop error screen. Restart your computer. If this screen appears again, follow the steps:

Check to make sure any new hardware or software is properly installed. If this is a new istallation, ask your hardware or software manufacturare for any Windows updates you might need.

If problem continues, disable or remove any ne... Read more

Answer:Blue Screen and Stop Log Error Message

Welcome aboard Download BlueScreenView (in Zip file)No installation required.Unzip downloaded file and double click on BlueScreenView.exe file to run the program.When scanning is done, go Edit>Select All.Go File>Save Selected Items, and save the report as BSOD.txt.Open BSOD.txt in Notepad, copy all content, and paste it into your next reply.=============================================================Download System Information for Windows (SIW free version)No installation required.After it scans your computer, navigate to Hardware>Sensors and post all info from there.

7 more replies
Relevance 69.7%

Hi, Toshiba Qosmio laptop - win 7 home - Toshiba sata dard drive. Blue screens in normal and safe mode. Things I've tried:
 
removed and swapped the ram chips
re-seated the HD
Checked the bios and HD is listed
Ran "Drive Fitness Test" and "SeaTools" - both do not see the HD
Ran "Memtest" - no errors
 
I don't know the history of the laptop, but the user suspects a virus or malware.
 
Any other suggestions would be appreciated - Thanks

Answer:Blue Screen stop error - unbootable

Instructions for a Windows 7 Repair installation.
 
A Windows 7 Repair Installation will require a installation disc.
 
If you do not have a Windows 7 installation disc you can download a free legal ISO image of Windows 7 SP1 at  Windows 7 Forums.  You will need to download the same version of Windows 7 that you have installed,  This image is hosted by the Digital River store which is an official distribution partner of Microsoft.  This is a genuine untouched image which is safe to download. 
 
Attention:  If you do have a Windows installation disc, skip Part A and go to Part B, Step 1b.
 
Part A, Steps 1a - 6a
 
How to burn ISO image using Windows Burn Disk Image.
 
Notice:  This applies only to Windows 7 and Windows 8, earlier versions do not have this.
 
1.  Place a blank CD or DVD in the tray of your optical drive and close the tray.
 
2.  After you have downloaded the ISO image you want to burn right click on the Start orb, then choose Windows Explorer.
 
3.  When Explorer opens click on Downloads in the left pane.  Scroll down till you find the ISO file you want and double click on it.  Click on Burn Disk Image.
 
4.  In the image below you will see Disk burner:, this should be set to the optical drive you want to use.  Click on Verify disc after burning if you want to Windows to verity the disc image after burn.  Click on burn.
 

 
5. ... Read more

1 more replies
Relevance 69.7%

Today while at Ebay I got a black screen, then blue screen with the message that Windows (xp) had been ended to prevent damage to my computer, then the following info...

-----------------------
Stop error

Check for adequate disk space.
try changing video adapters
check for Bios updates
disable Bios memory options such as caching or shadowing

Technical Information:

stop:0x0000008E (0xc0000005, 0xF72525c8, 0xF5cc98Ab, 0x00000000)
tcpip.sys-Address F72525c8 base at F724F000, Datestamp 444775d3

---------------------------

I got a similar screen several months ago. Restarted and everything has been fine till this. I restarted today and everything seems fine now, but should I be worried? Blue screens SCARE me!

running windows xp sp2 home on a Dell desktop Pentium 4, 2.4GHz. 256 Ram

thanks for any help
Susan
 

Answer:Blue Screen STOP error... yikes

http://trustyfiles.com/help-sw-xpsp2.php
 

2 more replies
Relevance 69.7%

I have been slowly searching the web on my laptop and trying to diagnose this problem that i am having (blue screen stop: 0x0000008E (0xC0000005, Ox804EEF98, 0xF44147DC, 0x00000000) with my home desktop computer (Compaq Presario 5300 US)...I believe it all started after i attempted to install symantec antivirus, internet explorer 7, or windows xp service pack 2...all within a day or twoI am away at school most of the time but have to manage my home computer for my parents when i am homeThe first symptom was the computer restarting by itself after loading windowsI then turned off the Automatic Restart functionThen upon restart the computer loaded windows and shut off to a blue screen displaying this message:A problem has been detected and Windows has been shut down to prevent damage to your computer.If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:Check to be sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.Technical Information:*** STOP: 0x0000008E (0xC0000005, 0x804EEF98, 0xF43DC7DC, 0x0000... Read more

Answer:Blue Screen Error Stop:0x0000008e

Hi cville, I think you are on the right path about the problem occuring after an install, it can be sometimes hard to track down but have a look at the link as it might be helpful http://support.microsoft.com/kb/930916/en-us

2 more replies
Relevance 69.7%

Since 7-4-2010, I've had a stop error 4 times. It happens when I've been using it for a while w/ multiple things going on (several docs & several browsers/windows/tabs open etc.) It's running slow (like when I type a couple of words, it takes a few seconds to show up on screen.) The error message is:

"A problem has been detected & windows has been shut down to prevent damage to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:
Check to be sure you have adequate disk space. If a drive is identified in the stop message, disable the driver or check the manufacturer for driver updates. Try changing video adapters.
Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced start-up options, and then select safe mode.

Technical information: *** STOP: 0x0000008E (0xC0000005, 0xBF22D0A6, 0xA8831574, 0x00000000)
***ati3duag.dll - Address BF22D0A6 base at BF185000, Datestamp 48286321
Beginning dump of physical memory Physical memory dump complete"

So, I have a few questions about this (although I appreciate any suggestions, even if not a direct answer to one of my questions - I may not even know the right thing to ask.)
What exactly is a stop error?
It says, "If a drive is iden... Read more

Answer:Stop Error - Blue Screen questions

16 more replies
Relevance 69.7%

Hi!

I'm having problem with windows rebooting randomly. This is the error message in the blue screen apearing:

IRQL_NOT_LESS_OR_EQUAL

BCCode : 1000000a
BCP1 : F78AB2D0
BCP2 : 00000002
BCP3 : 00000001
BCP4 : 804D9B68
OSVer : 5_1_2600
SP : 2_0
Product : 256_1


Do you have any idea of how to solve this? it's quite a pain in the..

All tips are warmly welcome!

Thanks
Niclas
 

Answer:Blue screen Windows Stop Error

All the crashes are caused by your Intel PRO/Wireless LAN Driver. See if there's an update available.

BugCheck 1000000A, {f78ab2d0, 2, 1, 804d9b68}
Probably caused by : w70n51.sys ( w70n51+2a3ae )
Image name: w70n51.sys Timestamp: Mon Oct 13 21:11:51 2003 (3F8AA497)
 

4 more replies
Relevance 69.7%

Hi there!

Can anyone help me troubleshoot a Stop 0x000000D1 error? I have a Dell desktop (with XP) that I rarely use and when I tried to use it today I got the dreaded blue screen. I've tried starting in Safe Mode but when I do I get a long list of multi(0)disk(0)rdisk(0)partition(2)\WINDOWS\system32\drivers\....... Help! What do I do?

I'm not extremely literate when it comes to computer terms so I'm hoping someone can help me out in semi-simple terms.

Thanks in advance!

Answer:Help! Blue Screen - Stop 0x000000D1 Error

Anything in C: > WINDOWS > MiniDump > ?

If so what are the dates of the crash files? Do they match up with when your system crashes?

Are you able to eventually get to the desktop in safe mode?

3 more replies
Relevance 69.7%

Hi I have just built my second pc.
This one is for my wife which she will use for the internet.
All went well and works well. But some times when I am using the internet Firefox, or Windows Explorer I get the blue windows Stop screen 050 and the pc restarts but I then get the screen to start in safe mode or start windows as normal. I start windows as normal, and every thing is ok. So I go back on the net and every thing is fine, but maybe after about 15 mins some times a bit longer it happens once more.
I am running windows 7.
Any help to sort this out would be Great. Thank you.
Regards Cornishman

Answer:Blue screen stop error on new Windows 7 PC

Hi, it will be helpful if you could post the exact error code.
Usually when a BSOD occurs, it stays for a second before the PC immediately restarts. This way we are unable to read what is written. To get around it, one has to disable the auto PC restart option from the StartUp & System Recovery settings. Knowing the error code, can help identify the problem/solution.
Disable UAC. Control Panel > System And Maintenance > System > Advanced System Settings > Advanced tab > Under Startup And Recovery > Click Settings > Clear the Automatically Restart check box > click OK. Enable UAC.
Meanwhile something or some links here may help you: How to analyse Windows 7 Stop Errors or Blue Screens. | The Windows Club

4 more replies
Relevance 69.7%

I'm getting the following when I turn on my computer:

On a Blue Screen

"A problem has been detected and Windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

check to be sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.

check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select safe Mode.

Technical Information:

*** STOP: 0X0000007E (0XC0000005, 0X82479089, 0XB3EB3BA4, 0XB3EB38A0)"

I've been having virus problems which have disabled my internet access. I ran Norton Antivirus 360 in Safe Mode Networking and it only found 1 cookie. When I start Windows I'd get pop-ups all over my screen continously. Now the system won't start windows as I can only get to the blue screen and no further.

I checked BIOS configurations and everything looks normal. No BIOS upgrades are needed. I try starting system on every different Safe Mode available but nothing works. I eventually wind up back at the blue screen.

Can anyone give me some guidance as to what I can check, change or do differe... Read more

Answer:Blue screen w stop: 0X0000007E error

Try downloading Hiren's boot cd http://www.hirensbootcd.net/ burn it onto a cd, set your pc to boot from cd drive. The disk has loads of tools on it so you can test a load of stuff. For this BSOD error which i myself recently had it is most likely to be a problem with your ram or hard drive. Once i had sorted my pc out when it had this problem it turned out that windows needed repairing so if you have the windows boot cd try using that as well, after memory and hard drive tests.

1 more replies
Relevance 69.7%

I just recently installed my intel core 2 duo in my computer, not sure if thats the problem. Somebody said that I should set something in my BIOS, but I don't know what to configure, hopefully you guys know.
I'm getting this when I try to start up my computer, I get this message after the windows logo.
A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:

Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

Technical Information:

*** STOP: 0x0000007B (0xBACC3524, 0xC0000034, 0x00000000, 0x00000000)


Computer Specs
Motherboard: ASUS P5NSLI
Memory: 4g Corsair DDR2
Video: NVIDIA 8800GT Alpha Wolf Edition 512MB
Processor: Intel Core 2 Duo E4500
Hard Drives: 2 Seagates, 1 300G and 1 180G
Power Supply: Antec Earthwatts 500 Watts
CPU Fan/Heatsink: The one that came with my processor

Answer:Blue Screen Of Death (stop error)

Give me an IM if you think you can help me at
AIM: mizdachubz

9 more replies
Relevance 69.7%

I have a WinXP home edition pc with an AMI motherboard. I have recently upgraded my video card to a Rosewill NVIDIA GeForce 4000, AGP, with 128mb DRAM. The motherboard has an AMD K7 Athlon XP processor, 1150 Mhz, 1.760V with 512mb ram. My system is locking up left and right and when it's not locking up, I am receiving this blue screen error: STOP 0x0000008E (0xC000001D, 0x8056BAD4, 0xF8C2DB00, 0x00000000). When I updated my video card, I went to disable my onbaord video card so that the system would only access this one however there isn't a way to disable it in the BIOS. It only asks me to select primary video and my choices are: Onboard AGP or PCI. I have tried both settings but neither works any better than the other. Any help, suggestions, are greatly appreciated.

Thanks.
 

More replies
Relevance 69.7%

I have tried to boot my computer but keep getting this same blue screen error. I have tried starting in safe mode and all the F8 and F12 options and still the same blue screen error. I cannot run CHKDSK /F as instructed because I cannot get away from the blue screen. I do not have my installation CD either. I have been trying to sort this for 2 days but to no avail. I am using a Dell Dimension 5150 PC with Windows XP Home edition operating system. I have run a system tree test and everything passes.

Can anyone help? I am at my wits end.

Many thanks.
 

Answer:Blue Screen Error STOP 0x24

you are going to need a cd now or soon anyhow so suggest getting one

could try but up to you as risks involved:

turn off remove power totally, remove side of comp...if you have a graphics crad remove it if you have more than 1 stick of ram remove all but 1 remove small silver battery for a minute put it back put graphics lead onto mobo vga outlet (if you had a card) re boot if no good then you need a disc or repair cd or a computer shop to sort out your hard drive
 

2 more replies
Relevance 69.7%

I'm hoping someone can help me I am getting a blue screen error that reads stop:c0000221 {bad image checksum} The image urlmon.dll is possibly corrupt. The header checksum does not match the computed checksum. I have not been able to get into safe mode nor will the installation c/d boot...i did change boot sequence but still no luck. I'm average user with no I/T knowledge but am able to follow directions...please feel free to talk as simple to me as possible! Thanks in advance for any help, of course i haven't done a backup lately and really don't want to loose my info.
 

Answer:blue screen error stop:c0000221

If you dont mind spending a little, this program will completely fix your problem>>

http://www.grc.com/spinrite.htm
 

2 more replies
Relevance 69.7%

I was removing some spyware and other malicious things from a friends laptop and then I went to reboot. After rebooting I get the blue screen, and it says " STOP: c0000135 [unable to locate componnent] This application has failed to start because basemcL32 was not found. Re-installing the application may fix this problem."

I tried booting in safe mode but to no avail. Any suggestions? Thanks in advance.

Answer:The Infamous Blue Screen (Stop Error)

safe mode not availiable? where abouts does it BSOD?

6 more replies
Relevance 69.7%

...so can someone explain???:

A problem has been detected and Windows has been shut down to prevent damage to your computer.

Follow these instructions;

Be sure you have adequate space.
If a driver is identified in the STOP message, disable the driver or check with the manufacturer for driver updates.
Try changing video adapters.

Check with your hardware vendor for any BIOS updates. Disable BIOS memory updates such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart the computer, press F8 to select Advanced Startup Options and select Safe Mode.

TECHNICAL INFORMATION:

*** STOP: 0x0000008E (0x0000005, 0xBFC1E780, 0xA1172B24, 0X00000000)

***nv4_disp.dll - Address BFC1E780 base at BF9D5000, Data stamp 48ebd26f

Beginning dump of physical memory.
Physical memory of dump complete.
 

Answer:Stop error/blue screen - cant work out what to do...

16 more replies
Relevance 69.7%

I am currently running win xp home edition upgraded from 98 se On a low budget ecs mobo (but with an AGP slot).
Athlon XP 1900+
768 MB RAM
40 GB Maxtor 7800 RPM HDD
a pair of CDRW's
and sometimes, but not usualy a NVidia GeForce 4 mx 440

so here we go.......

When using any graphics intense software, or even graphics intense websites, my comp freezes (no video movement, no keyboard, no HDD activity nothing) .

I was told my mobo was too low end to support a high end graphics card, and that I must upgrade the mobo, which brings me to the problem that brings me here......

I purchased a ECS K7ama mobo, and followed the manual to a T.
Shorting the right jumpers, and opening the others. I am running the exact same configuration as before with the exeption of the motherboard, but when I boot, I get a blue screen of death.

The error message ( a stop error 0x0000007 or something) states that I have a faulty hard drive or hard drive controller.
I have checked the mobo for xp compatibility, with no luck, but everything else is XP fine. I don't want to reinstall everything from scratch if I dont have to, especially if it isnt going to fix my problem.

Any help would be appreciated

BEN
 

Answer:blue screen stop error on new mobo

Did you use the hard drive on the new motherboard (with XP on it) and just swap everything out? If you did, then the drivers for the old motherboard might be confusing the new motherboard. You might be better off reformatting the drive and then loading XP and the drivers for your new motherboard.
 

3 more replies
Relevance 69.7%

The full stop is:

STOP: 0X0000007E (0XC0000005, 0X82483673, 0X82E57650, 0X82E5734C)

My laptop (Dell Inspiron 64000) came up with this error when I tried to load it last night, the computer gets to the point where the loading bar is at the bottom of the screen then immediatley after there is the blue screen. If I try and restart the same happens. I've tried running in safe mode and again the same issue, also I've tried to boot it from the last successful start up, Same again.

I'm really stuck as to what to do with it, or even what the problem is!
I've had an issue with unwanted internet pop-ups recently, so I believe it may have some spyware, I have run several scans and deleted all that it's found but the pop ups are still fairly consistant.
I have an essay saved on it (that I foolishly havn't backed up anywhere else) that's due in in a few days so this is quite urgent.
Anyone have any ideas?
Any input would be greatly appreciated!
If you need any more information i'll endeavour to provide it but I'm not getting much luck, constant blue screens at start up don't provide me with much in the way of help!

Thanks!

Answer:Blue screen stop error 0x0000007e (...)

If I try and run startup Repair it tells me that windows cannot repair this computer automatically and gives me the problem details:

Problem Event Name: StartuprepairV2
Problem signature 01: Autofallover
Problem signature 02: 6.0.6000.163836.6.0.6000.16386
Problem signature 03: 6
Problem signature 04: 327685
Problem signature 05: NoRootCause
Problem signature 06: NoRootCause
Problem signature 07: 0
Problem signature 08: 2
Problem signature 09: WrpRepair
Problem signature 10: 0
OS version: 6.0.6000.2.0.0.256.1
Locale D: 1033

When I send the information the Diagnosis and repair details come back with all test results as: "Completed Successfully. Error code = 0x0"

Root cause found:
Unspecified changes to system configuration might have caused the problem.

3 more replies
Relevance 69.7%

Hi folksWe have had this happen twice today and the error code on the Blue Screen reads as follows:***STOP: 0x0000008E (OXC0000005, OX805652E0, OXB9F3FC08, 0X00000000)Both incidents happened whilst the computer was being used for different reasons - once while gaming and once while using remote desktop.Anyone got any ideas what might be wrong?Thanks

Answer:STOP error - Blue screen of death

I've only had a blue screen fault once. Ignoring all the code like above, there was a file name on there that ended with what looked like a file extension. I searched my hard drive for the same filename and found it to be one from the Deutsch Telekom software I had installed a few weeks before. I never used it anyway so I just uninstalled it. Problem solved.

2 more replies
Relevance 69.7%

This computer was given to us in April 2011. Shortly after we got it, my daughter reports that she started getting different warning messages but she didn't pay attention to them. The previous owners said they never had this problem. The main one we get now is a blue screen with one of the following messages listed before the dds log.The only way to use the computer is to pop the battery out and restart it. It might do it on Startup, after a few hours, or even in Safe Mode. It also takes over my search engine sometimes.

It came with Norton 360. After this problem started, I got rid of Norton and installed Malwarebytes, Spybot, SuperAntispyware, AVG, and Zone Alarm. They are all updated, and each time I run them, they find some problem almost every time including Trojan.Hiloti, Rootkit.TDSS, MyWebSearch,Trojan.Trecur.XGen, Trojan.BHO, PUM.Disabled.SecurityCenter, and others. They always say they are removed completely, and often on the next scan it is clear, but then they either reappear or a new one with a different name pops up. I think it's all the same. I tried System Restore, but all the dates before May have been removed.

These are the messages (I've listed 3):
A problem has been detected and Windows has been shut down to prevent damage to your computer.

IRQL_NOT_LESS_OR_EQUAL

If this is the first time you’ve seen this Stop error screen. Restart your computer. If this screen appears again, follow the steps:

Check to make sure any new ha... Read more

Answer:Blue screen with Stop Error Message

Good evening. Download TDSSKiller.zip from Kaspersky from here and save it to your Desktop. You will then need to extract the file(s) from the zipped folder.
To do this: Right-click on the zipped folder and from the menu that appears, click on Extract All...
In the Extraction Wizard window that opens, click on Next> and in the next window that appears, click on Next> again.
In the final window, click on Finish
Please close all open programs as this may result in a reboot being necessary.
Double click TDSSKiller.exe to begin. Click Start scan and allow the tool to do just that. One the scan has completed, if the tool has identified anything allow it to carry out it's default action(s) - you'll need to click Continue where appropriate. Finally, if it prompts you to reboot your machine, please click Reboot Now and ensure that your machine does so.
If the scan finds nothing, please click the Report button and let me have a copy of the text file that opens. If you reboot your machine, the log, which i'd like to see, will be located at the root of you hard drive as C:\TDSSKiller.Version_Date_Time_log.txt.
Please check that you get the one with the right date and time.

25 more replies
Relevance 69.7%

Hello All,

I was having trouble logging into my computer after I used Win Optimizer and deleted a bunch of DLL files. One of which was HAL.DLL. After I restarted my computer of course it wouldn't load because I got a message telling me the file was missing please re-install.

I used the windows XP recovery console and try to repair windows but kept getting the blue screen of death. With various codes while it was retrieving files for the repair.
The most frequent the Stop Ox0A error. So I gave up on that and used the recovery console to Expand the file back in using this technique. Found on multiple websites and message boards.

Option 1:

Boot from your CD and follow the directions to start Recovery Console. Then:

Attrib -H -R -S C:\Boot.ini
DEL C:\Boot.ini
BootCfg /Rebuild
Fixboot

Option 2:

Boot from your CD and follow the directions below to start Recovery Console.

Insert the Setup compact disc (CD) and restart the computer. If prompted, select any options required to boot from the CD.
When the text-based part of Setup begins, follow the prompts; choose the repair or recover option by pressing R.

If you have a dual-boot or multiple-boot system, choose the installation that you need to access from the Recovery Console.
When prompted, type the Administrator password. (if you didn't create one try pressing enter).

At the system prompt, type Recovery Console commands; type help for a list of commands, or help commandname for help on a specific command.
... Read more

Answer:Stop Error Blue Screen During Installation

Did you repartition the drive or just format the boot drive?

Have you tried simplifying the hardware configuration? See "look for hardware issues" in the article below:

http://support.microsoft.com/?kbid=314063&sd=RMVP

Is there ever a driver file mentioned in these STOPs?

Other 0A articles can be found here:

http://aumha.org/win5/kbestop.htm
 

3 more replies
Relevance 69.7%

Hello,The background: I am trying to install Windows XP Home onto a semi-new (custom built) machine. I am using a Gigabyte GA-G41MT-USB3 motherboard, a 500gb SATA hard drive (brand new), and 4gb DDR3 ram (2x2gb cards). It is an old copy of Windows XP - it may have SP1 included but I'm not sure.The problem: Computer POSTs fine, detects HDD fine (according to BIOS), RAM tests fine, enters BIOS setup fine, starts Windows setup fine. But... During setup, after Windows loads files, drivers, etc., and just after the point where it says "Setup is starting Windows", it goes to a blue screen with the following error message, every time:"A problem has been detected and Windows has been shut down to prevent damage to your computer.If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.Technical information:***STOP: 0x0000007B (0xF78D2524, 0xC0000034, 0x00000000, 0x00000000)"Steps I took: After reading about other people having similar problems, I assumed that it was because I was trying to install an old copy of XP onto a SATA drive. My machine doesn't have an A:/ drive, so I downloaded nLite and integrated the drivers fro... Read more

Answer:Getting blue screen Stop error during XP install

Please post your last session.ini

19 more replies
Relevance 69.7%

My Dell 8300 occasionally crashes on boot. The fault is intermittant. When it happens I have to pull the power, wait a few seconds and reboot. I may even have to do this twice, before it fully boots.

Here is the error message on the Blue Screen.

STOP: 0x0000008E (0xC0000005, 0x804DA2C0, oxA645B42C, 0x00000000)

The desktop develops and half way through it crashes. As I said it's intermittant. Once it fully boots it's perfect.

I think it's clean. Latest version on Norton Internet Security, SuperAntiSpyware, Spybot and SpywareBlaster are installed, fully updated, and the machine is regularly scanned.

Any help would be much appreciated.

Thanks,

PeterB

Answer:Blue Screen Error STOP: 0x0000008E

Check your devices in Device Manager (Start > Run > type "devmgmt.msc" (without the quotes) and press Enter). Look for any "!", "?" or "X" symbols.

10 more replies
Relevance 69.7%

i have been having a reocurring issue trying to edit some video and been getting stop errors at the same point along the process. i have used a debugger to obtain a description of the minidump that occurs with the stop error and have copied it below. i have also been reading about disabling caching and shadowing features which are mentioned in the stop error desctiption screen.

cpu information:

dell dimension 8300
windows xp professional 2002 (32-bit)
service pack 3
pentium 4 2.6 GHz
2.59 GHz, 3.25 GB of RAM
NVIDIA GeForce 6200 vid card

this is my first post and any information would really really be appreciated.
* * * *
Microsoft ® Windows Debugger Version 6.10.0003.233 X86
Copyright © Microsoft Corporation. All rights reserved.
Loading Dump File [C:\WINDOWS\Minidump\Mini122908-04.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows XP Kernel Version 2600 (Service Pack 3) MP (2 procs) Free x86 compatible
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 2600.xpsp_sp3_gdr.080814-1236
Machine Name:
Kernel base = 0x804d7000 PsLoadedModuleList = 0x805634c0
Debug session time: Mon Dec 29 22:56:43.446 2008 (GMT-8)
System Uptime: 0 days 0:03:26.071
Loading Kernel Symbols
...............................................................
............................................................. Read more

Answer:help diagnosing blue screen stop error

My guess would be that it's your VideoWave program...possible corruption/damage in either the program itself or the drivers it employs.http://kb.roxio.com/content/kb/General%20I...mation/000071GNI would suggest uninstalling/reinstalling the program and updating same...along with a defrag of the partitions which you are using for storage of outputs/inputs you edit.Louis

4 more replies
Relevance 69.7%

I have a Dell Latitude D520 laptop running XP. I only use my laptop when travaling for work. I have not booted this computer for a couple of months. When I booted it this afternoon I got a blue screen saying "A problem has been detected and windows has been shut down to prevent damage to your computer"...Technical Information: *** STOP: 0x0000007E (0x80000003, 0x805C370C, 0xF8A572B4, 0xF856FB0)

I tried starting it back up in Safe Mode but all that comes up is a blank blue screen.

I have a big presentation Thursday and need my laptop for the presentation.

PLEASE HELP!!

Answer:Blue Screen Stop: 0x0000007E Error

Insert the Windows XP CD into the CD drive, and then restart the computer. Click to select any options that are required to start the computer from the CD drive if you are prompted. When the "Welcome to Setup" screen appears, press R to start the Recovery Console. If you have a dual-boot or multiple-boot computer, select the installation that you must access from the Recovery Console. When you are prompted, type the Administrator password. If the administrator password is blank, just press ENTER.Type: chkdsk /rIt's important to have a space before the "/".To exit the Recovery Console and restart the computer, type exit at the command prompt, and then press ENTER.

15 more replies
Relevance 69.7%

Hi I have a blue screen of death stop error 0x000000F4. and I run out of ideas
Here is the sequence of events, First I clone my laptop HD with a similar 100G one during the 4-5 cloning step I get a warning that something on that partition could not be access so just out of curiosity I installed the clone HD to see what will happened and to my surprised it work fine, if left idle I get the blue screen with the stop error I dint knottiest the error # never the less I removed it for re-cloning and install the original one so as to go back to work.
I knottiest the laptop was unusually slower with the original HD I checked with Process Explorer and the Hardware Interrupts CPU working over time, after living the laptop idle for several hours I get the blue screen, If am working on it is fine but the hardware interrupts CPU is still high.
I have done all the cleaning, scanning and defrag necessary before the cloning.
Any help on this one?

I have Inspiron E1705
WinXp media
 

More replies
Relevance 69.7%

I have reinstalled win7ultimate over win7home prem. I selected clean install and it put the old system into the windows.old folder. I then put office2010 onto it. With or without office installed I occasionally getting what I call the half blue screen of death. I'm getting the windows has stopped to an unexpected error screen. Any ideas as to how to handle this. Thanks

Answer:Blue stop screen unexpected error

You can try an Office repair.Repair or remove Office 2010http://office.microsoft.com/en-us/o...Also, you can post your dump file.How to open DMP files in Windows 7?http://windows7themes.net/how-to-op...

19 more replies
Relevance 69.7%

Hey there,

Sorry if I'm repeating the subject here but I got this recurring problem every 4 to 5 hours and can't seem to solve it.

I'd appreciate any help here.

I'm pasting the error from Event Viewer, please help me!

Event Type: Error
Event Source: System Error
Event Category: (102)
Event ID: 1003
Date: 23-02-2006
Time: 20:16:35
User: N/A
Computer: MIKEMELGA
Description:
Error code 1000007e, parameter1 c0000005, parameter2 f5b6f228, parameter3 f6ed9bf0, parameter4 f6ed98ec.
Data:
0000: 74737953 45206d65 726f7272 72452020
0010: 20726f72 65646f63 30303120 37303030
0020: 50202065 6d617261 72657465 30632073
0030: 30303030 202c3530 36623566 38323266
0040: 3666202c 62396465 202c3066 64653666
0050: 63653839


Event Type: Error
Event Source: Service Control Manager
Event Category: None
Event ID: 7000
Date: 23-02-2006
Time: 20:16:26
User: N/A
Computer: MIKEMELGA
Description:
The Creative Service for CDROM Access service failed to start due to the following error:
The system cannot find the file specified.


Thanx in advance! (^_^)y
 

Answer:STOP Error (a.k.a. blue screen of hell)

Hi,

Zip 5 to 6 minidumps and attach the zip files here. You can find the minidumps at the folder \windows\minidump
 

3 more replies
Relevance 69.7%

hey!

well basically ive been having this blue screen issues for some time now, however i kept ignoring it until now its really starting to annoy me lol

I get the messages:

Stop error blue screen

BAD_POOL_CALLER

DISABLE BIOS MEMORY

***stop: 0x000000C2 (0x00000099, 0x8462DC98,0x00000000,0x00000000)

Well that is the basic info the blue screen gave me,, I have tried removing some programs liek newly installed which were: Itunes, RegCure, Imtool, 4 on demand and other free-ware programs to convert video files.

I have a HP Pavillion DV6000 , 250GB, intel core 2 duo processor, vista home premium, 2 GB ram (this laptop is quite new, only had it for few months)

Thanks!
Joanne
xx

More replies
Relevance 69.7%

Hi everyone,
Im having trouble for the past few weeks with my laptop. I've got a Dell Inspiron 6400 and Im running XP. The problem is, sometimes when I turn it on I get a blue screen with the error msg Stop 0X0000007E (0xC0000005, 0XF82CCFD7, 0XF89DEA84, 0XF89DE780). I have to keep turning the laptop off and then run it again and again and eventually it will work. I've tried searching this problem but cant find any solutions out there
I also got this error for the first time this morning
'rixdptsk.sys Address F784CFD7 base at F784B000 date stamp 42D62235
Physical memory dump'

Any idea's???
Thanks,
JGK

Answer:Stop Error Msg (The dreaded blue screen)!!

From www.file.net:

"Important: Some malware camouflage themselves as rixdptsk.sys, particularly if they are located in c:\windows or c:\windows\system32 folder. Thus check the rixdptsk.sys process on your pc whether it is pest."

2 more replies
Relevance 69.7%

So I have a Dell and am using Windows XP. I also use the free AVG antivirus program. Within the past couple of weeks I have gotten a couple of viruses. The first one was Thinkpoint, but I removed that and the computer started working normally. A week later I got another kind of rogue virus and removed that and everything was working normally. Today I think I got another virus because suddenly my computer starting working really really slow. There were no pop ups like the last one so I was slow to figure out I got a virus. It would keep freezing too. I ran malwarebytes and it found 5 infected files. When I tried removing them it said it could not remove some of the files and if I wanted to restart. I said yes but then the computer froze. I turned it off and when I turned it back on I got a blue screen error. It told me something was wrong with Windows which caused it to shut down and that I need to check for viruses or hardware changes. The technical information was

***STOP 0x0000007B (OxF7C6A528, 0xC0000034, 0x00000000, 0x00000000)

it said to run CHKDSK /F but once I get to the blue screen I can't do anything. I've tried running in safe mode and safe mode with command prompt but the blue screen still pops up. I also can't find my Windows Installation CD
I have a lot of documents on my computer so I want to fix it without losing everything.
PLEASSEE HELP!
 

More replies