Computer Support Forum

code 10 error,usb to rs232 cable

Question: code 10 error,usb to rs232 cable

i am using core 15 processor,dell n4110 laptop,, i tried to connect profolic usb to serial(rs232) cable. i tried in win7 professional and ultimate.in professional i installed but device is not working.. error statement is coming as "this device not srarted(code 10 err0r)"

Relevance 100%
Preferred Solution: code 10 error,usb to rs232 cable

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

Answer: code 10 error,usb to rs232 cable

Hi Ebin
Try to visit the following site:

USB to RS232 cable keep receiving a Code 10 message - Microsoft Answers

Good luck

1 more replies
Relevance 66.42%

I have used X10 successfully for many years and controlled my whole house via a CM11A controller. This controller connected to my PC through a serial port and could be easily programmed to change lights etc. Since the old PC died and I have bought a new one there is no serial socket on it. I got a cable adapter recently and installed the driver. After some jigging to get the device to be on COM2 (CM11A only allows 1 - 4) I still can't program the CM11A. The Activehome software fails its communication test to COM2. I downloaded a serial port monitor and it looks like bits are sending. Now I'm stuck! Any ideas out there?
 

Answer:USB to RS232 cable problems

Look in Properties for COM2 and check the baud rate, parity, number of bits, etc is configured properly. The manual I found says 4800 baud, no parity, 8 data bits, 1 stop bit.
 

2 more replies
Relevance 66.42%

I bought a hand held scanner which had a female 9 pin connector. My laptop only had a 15 pin rs232 connector. As I had spare usb ports I got a USB cable that had a male 9 pin attachment at one end. I also downloaded some drivers for HL-340. When the cable is attached it shows up as com4 usb-serial ch340 usb2.0-ser!. When I run the software associated with the scanner, a light on it flashes, but nothing else happens.Does anyone have any idea if I am using the combination of cables etc?

Answer:Rs232 to USB cable problem

If the port on the Laptop is an RS232 Serial port, are you sure it isn't 25-pin male? You should be able to get a 25-pin female to 9-pin male RS232 Serial Cable to connect the laptop and scanner directly. Have a look at this page click here

10 more replies
Relevance 66.42%

My new laptop doesn't have a Serial RS232 connection but I use one occassionally to download data to a Satellite Receiver.I've bought a RS232 to USB cable which was supplied without a driver. I've tried installing using XP's integrated drivers without success. Can anyone suggest where a suitable driver might be sourced? I've tried click here

Answer:USB to RS232 Serial cable

Possible source:click here(Drivers link, hopefully may work!)

2 more replies
Relevance 66.01%

I can't get my usb to rs232 cable to install and vista keeps indexing the com port as it trys the next install. I have downloaded the driver, updated the driver, deleted the driver and reloaded the driver to no avail. Now it shows 26 com ports in use and tells me the device I am trying to install is trying to use a display name that is already in use. How do I clear this up so I can install this device?

More replies
Relevance 66.01%

What is the maximum length that you can run a serial cable before having communication problems?
 

Answer:RS232/serial cable length

11 more replies
Relevance 66.01%

Hello All,

As a surveyor, I'm trying to slowly solve all the glitches on my new Windows 8.1 laptop.

1. Mouse

I often visit this NSW government site SIX Maps

When navigating the map, you use the mouse scroll wheel to zoom in or out and hold down the left mouse button to pan.

In my new windows 8.1 laptop, the scroll and pan functions won't work.

Iv'e tried 4 different mice and none of them work but they all work on my old XP laptop.

I've also tried 2 browsers (Chrome and IE)

I have also been in touch with the NSW goverment support team to no avail.

Looking in control panel, I couldn't recognise anything that would help.

Does anyone have any ideas?
2. USB to RS232 serial port cable replicator

This cable is used to download/upload information to the survey instrument. It worked fine on Windows XP, but will not work on Windows 8.1. It may be something to do with the port configuration.

Please note that the software is very old and I had to create a virtual XP machine using VMWARE to run it. (As well as some other obsolete software such as XTGOLD and Q.EXE! Any one remember these? I've yet to come across any file editing program to equal Q.EXE)

Hopefully someone will have some ideas otherwise I'll have to go back to the manufacturer and they'll charge more than I paid for the computer!!!

Thanks in advance for your help,

Michael

Answer:Problem with mouse and USB to RS232 cable

Well, I tried the link you provided and I was able to scroll using IE, Logitech Mouse, and Windows 8.1 Pro (64 bit). However, when I first accessed the site, it said that their site would work better with FireFox or Chrome. I have Chrome installed but did not try it.

USB to RS232, which end connects where? Does the USB end connect to the computer or the survey equipment? When running your XP, does it provide an error when you try to connect upload/download data? I would think that your VMWARE and XP will be able to handle everything, but you will need to play with port settings to have everything configured the way it was before. For example, my wife's computer is Windows 8.1 Pro, and I have her run VMWARE and Windows XP so she can use the embroidery module for her sewing machine. The one thing you have to do is to make sure that when you start the VM machine, you must tell the VM machine to use anything plugged into the USB ports to be used in the XP and not the Host machine.

Anyway, don't give up yet and keep poking around you'll find a solution.

5 more replies
Relevance 65.19%

Hi - here's an idiot question for you. I need to know whether or not my laptop (Dell Inspiron 2200) has something called an RS232 serial port. I think it probably doesn't, as I couldn't find it mentioned in System Information. But I'd like to know for sure before I fork out 30 for a USB adapter, which is what I'm told I'll need if there is no RS232 port. It's needed for a programme called DesignaKnit 7 - details of which can be found at http://www.softbyte.co.uk/dk7.htm, if anyone is interested. So, can anyone tell me how to find out for certain whether or not I have this port? Thanks v much, Helen
 

Answer:Do I have an RS232 serial port for cable link?

You do not have an RS-232 port on that laptop. Note that the site in question has specific recommendations for the RS-232 <-> USB link device, and I'd pick one of their recommendations: http://www.softbyte.co.uk/usb_conv.htm
 

3 more replies
Relevance 65.19%

Anyone know why my dell p1110 monitor turns off when I connect a RS232 <> TTL cable to the four pin header... I'm trying to use windas to fix the oh-so common brightness issue these monitors have and can't get very far without being able to connect the cable and view the screen at the same time. It doesn't fully turn off, but goes blank and the green light turns amber. Any suggestions are greatly appriciated!

More replies
Relevance 64.37%

I have Dell&#153; PowerConnect&#153; 3024 managed switch. I don't have the IP of the switch and I don't have RS232 cable. There is no reset button.

I don't know the IP so I can login from the web browser using Ethernet
 

Answer:Dell PowerConnect 3024 lost IP and RS232 cable

8 more replies
Relevance 64.37%

I b ought one of these adapters off eBay so I could connect my GPS to my computer via USB, my old cable was the serial port. Anyhow, the seller told me it would work with Vista but she did not tell me it wouldn't work with Vista Premium. When I connect the device it tries to find the drivers but is unable to do so...does anyone know where I can get the right driver? The CD that came with the cable is worthless. Thanks
 

Answer:USB to RS232 Serial 9Pin DB9 Cable Adapter Driver

6 more replies
Relevance 56.58%

XPS M1730 internittant problem - machine crashes and will not reboot. Diagnostic error code 2000-0411.
After a couple ot tries it restarts.
Keyboard backlight has not worked for a long time - Fn rt arrow does nothing.
Any ideas? Could be a cable is not seated properly but I'm not anxious to pull the machine appart.
Thanks

Answer:Error code 2000-0411 Keyboard backlight cable not detected

MS72
Sorry to hear about the troubles.  The following link gives details on the basic diagnostics.
The code 2000-0411 means a possible failed hard drive.
http://support.dell.com/support/topics/global.aspx/support/kcs/document?&docid=DSN_300428&isLegacy=true#HDD
I suggest reseating the hard drive.  Disconnecting the drive and reconnecting it. Here is a link from the service manual on removing hard drives.
<ADMIN NOTE: Broken link has been removed from this post by Dell>
Once reseated and try diagnostics again.  If it gives the same error you will need to replace the drive.
 
TB

9 more replies
Relevance 56.17%

ok so ive got this gateway solo 1450 laptop and i got this error. PXE-E61 Media Test Failure, Check Cable" Error Message. i went into the bios and got nothing out of changing the boot order or resetign to system defaults. there was a few times where i was able to get past that error and it went into the screen where it asks how you want to boot up. last known good config, start windows normally. safe mode, safe mode w/ command prompt, Etc. i really need to get this working any help is appreciated. thank you.

i am also running windows XP home... i think.
 

Answer:Solved: PXE-E61 Media Test Failure, Check Cable" Error code

You're trying to do a PXE boot (which is boot from a network server) and you don't have your network cable connected.

Are you trying to PXE boot? If not, you usually can completely disable PXE in your BIOS. If you don't need it, disable it. If you do, make sure that you are plugged in to your network before turning your computer on.
 

1 more replies
Relevance 55.35%

I'm running a Dell XPS 8700 with Win 7.
It's been having problems waking up from SLEEP mode.
The last few days it refused to boot up after sleep mode.
I ran diagnostics and got this error:
Error code 0600:5127 CABLE - bios Diag interface function was not detected
What is this error and how can I fix it?
THanks,
bob

Answer:Error code 0600:5127 CABLE - bios Diag interface function was not detected

Error Code 0600-5127
CABLE - RTC battery was not detected
Time for new DL2032 battery.

1 more replies
Relevance 50.02%

Hello all,

I have a problem with Windows Update agent on Windows 7 SP1 enterprise.
We are using Configuration Manager 1606 and Windows 7 SP1 and about 140 computers works without any problem.
On the other 10 computers I got the following error message in the windowsupdate.log:
WARNING: SyncUpdates failure, error = 0x8024400D, soap client error = 7, soap error code = 300, HTTP status code = 200
WARNING: SOAP Fault: 0x00012c
WARNING:     faultstring:Fault occurred
WARNING:     ErrorCode:InvalidParameters(7)

I've tried several actions although none does any help. Here is the list of actions:
- upgrade windows update agent to the latest version
- windows update agent reset by this instructions https://support.microsoft.com/en-us/help/971058/how-do-i-reset-windows-update-components
- empty Temporary Internet files
- check the rules and blocked traffic on windows firewall and physical firewall between server and workstation vlan
- sfc /scannow

It looks like significant Windows 7 error, although reinstalling is not my option.

Thanks for any help!
GregaR

More replies
Relevance 49.2%

Ok - I'm trying to fix my friends' computer - Toshiba Satellite L455-S5975 running Windows 7 32-bit

Windows firewall is off and I need to "Update Firewall Settings". When I click use recommended settings, I get a message that says it "can't change some of your settings. Error code 0x80070424" I get the same thing when I click on "Turn Windows Firewall on or off" and "Restore Defaults"

When I click on "Advanced Settings" I get "There was an error opening the Windows Firewall with Advanced Security snap-in" followed by it "failed to load. Restart the Windows Firewall service on the computer you are managing. Error code 0x6D9."

I scanned the computer using both Avast and Microsoft Safety Scanner (full scan and took over 2 hours) - no infections or issues found

I installed all Microsoft updates and followed suggested restarts.

I ran Microsoft Fix It and I get a message that the firewall isn't running or stopped and it can't be fixed.

I have gone into services as an administrator to try and start Windows Firewall...it isn't there - not in the list of services (local)

I also used SlimDrivers to update all the drivers on the computer.

What I am not seeing is how to uninstall and reinstall Windows Firewall...any other program or hardware issue, that would seem to be the easiest solution - but I have yet to see how to do that with Windows Firewall.

I even started the computer in safe mode... Read more

Answer:Win7 Firewall won't turn on error code 0x6D9 and error code 0x80070424

What other Anti-virus was on the computer before Avast?

3 more replies
Relevance 49.2%

I have a new Toshiba L550 1C8 computer with Windows 7 64-bit.

The problem is, that I can?t burn my files on my preinstalled PIONEER DVD-RW DVRTD09A DVD-drive !

If I right-click the file and choose ?Send to E:DVD-drive? I got the error code 0X8007045D.

If I use the preinstalled Toshiba Disc Creator I got the error code 380136-24-00000000.

What?s wrong.


Ole.

Answer:Satellite L550-1C8: error code 0X8007045D and error code 380136-24-00000000

Hi,

Try removing the upper and lower filters to restore functionality.

Instructions: http://support.microsoft.com/kb/982116

2 more replies
Relevance 48.38%

Computer model: Panasonic Toughbook CF-31
OS: Windows 7 SP1
Processor: Intel Core i5-2540M CPU @ 2.60GHz 2.60GHz
RAM: 4 GB (3.89 GB usable)
System type: 64-bit

CBS Log
CBS.zip - Google Drive

I ran the SURT tool Windows6.1-KB947821-v34-x64.msu.
Ran fine, no problem.

Ran sfc /scannow
"Verification 100%"
"Windows Resource Protection could not perform the requested operation."

Also ran
Malwarebytes
JRT.exe
Adwcleaner
Hitmanpro_x64

I still get the "Windows Update Error, Error Code 80070643, Code 9C57"

Answer:Windows Update Error, Error Code 80070643, Code 9C57

Hi Qpuser,
lookin at your logs
couple of questions
Are you dual booting or have the OS on your D drive/partition.
can you also run, in following order

http://www.sysnative.com/niemiro/apps/SFCFix.exe
http://go.microsoft.com/fwlink/?LinkID=52012
and sfc /scannow

copy/paste the results please.

Roy

1 more replies
Relevance 47.15%

This is a desktop PC with Windows 7 Ultimate 64 bit installed. I'm trying to repair with the disk it was installed with originally. The reason for attempting the repair is that the System File Checker says there are files that it could not repair when I ran it. I ran it originally because I couldn't install or uninstall anything. I would get an error: This application was unable to start correctly. With error message (0xC0000006)

Now trying to repair Windows 7 with the upgrade option I get:
Windows was unable to create a required installation folder. Please reconfigure your boot.wim to use the flag 9 settings for the first image and restart your installation. Error Code: 0x803002f

Any help greatly appreciated....

Answer:Started with error code 0xC0000006 and now I have Error Code: 0x803002

You may need to attempt SFC up to 3 times to repair damaged System Files. But first disinfect per Troubleshooting Steps for Windows 7. If there is any problem go with the bootable scans in Troubleshooting Windows 7 Failure to Start as the OS may be in the death grip of infection.

Then SFC may run better from the Win7 installation media or System Repair Disk Command Line: SFC /SCANNOW Run in Command Prompt at Boot.

If these fail then you can try the Repair Install after establishing a Clean Boot per Troubleshooting Steps for Windows 7.

But you may be better off copying out your files to quarantine to follow these same steps for a perfect Clean Reinstall - Factory OEM Windows 7 which compiles everything that works best in tens of thousands of installs we've helped with here.

1 more replies
Relevance 47.15%

Boot configuration data file is missing some required informationFile   BCDError Code oxc000000d Any fixes for this? Computer wont start up. Worked fine this morning. Got this message this afternoon.













Solved!

Go to Solution.

Answer:Error code oxc000000d acer aspire R14 error code o...

First of all try to check if ALT+F10 at boot take you to windows recovery and you can reach command prompt from there:troubleshoot-advanced options- command prompt (if this works, go to point 4, if not point 1)1. create a vanilla Windows 8.1 installation media from this link:http://windows.microsoft.com/en-us/windows-8/create-reset-refresh-media2. Once you boot using the Windows installation disc, on the Windows 8.x installation window, click on Repair your computer.3. Click on Troubleshoot and in the Advanced options. First thing you may try is the Automatic Repair.4. If that does not help, then select Command Prompt. Enter the following four commands into the prompt.bootrec /fixmbrbootrec /fixbootbootrec /scanosbootrec /rebuildbcdOnce the command completes, restart the computer.

3 more replies
Relevance 47.15%

Hi All,
I'm new here and I think I messed up the post that I made. I had meant to say that all of a sudden I can't use windows installer service I get error code 8007641 or error code 641. I'm unsure why I'm not able to use windows installer anymore and I'm not able to get valuable updates from windows without it. Has anyone else ever had this problem and if so, were they able to come up with a solution? Thank you. This is my first day on the site and unsure how to get around on it, but it seems like it's an exciting site and I'm looking forward to using it.
Thanks,
Miket797

Answer:Windows Installer, Error Code 8007641 or error code 641

DownloadmsiserverLaunch it,click YESRestart the PC and try to updateIf you still have issuesDownloadmini toolboxCheckmark following boxes: List last 10 Event Viewer log List Installed ProgramsClick Go and post the result.

2 more replies
Relevance 47.15%

Boot configuration data file is missing some required informationFile   BCDError Code oxc000000d Any fixes for this? Computer wont start up. Worked fine this morning. Got this message this afternoon.










Solved!
Go to Solution.

Answer:Error code oxc000000d acer aspire R14 error code o...

First of all try to check if ALT+F10 at boot take you to windows recovery and you can reach command prompt from there:troubleshoot-advanced options- command prompt (if this works, go to point 4, if not point 1)1. create a vanilla Windows 8.1 installation media from this link:http://windows.microsoft.com/en-us/windows-8/create-reset-refresh-media2. Once you boot using the Windows installation disc, on the Windows 8.x installation window, click on Repair your computer.3. Click on Troubleshoot and in the Advanced options. First thing you may try is the Automatic Repair.4. If that does not help, then select Command Prompt. Enter the following four commands into the prompt.bootrec /fixmbrbootrec /fixbootbootrec /scanosbootrec /rebuildbcdOnce the command completes, restart the computer.

3 more replies
Relevance 47.15%

No-one replied to this post and so the problem was never fixed.
(The updates continued to fail downloading or installing)
I upgraded to Windows 10 Home and thankfully didn't need to have the updates installed to upgrade.

Back in April this year I downloaded two important updates:

1) Security Update for Microsoft .NET Framework 4.5.1 and 4.5.2 on Windows 8.1 and Windows Server 2012 R2 x64-based Systems (KB3023222)

2) Security Update for Microsoft .NET Framework 4.5.1 and 4.5.2 on Windows 8.1 and Windows Server 2012 R2 x64-based Systems (KB3032663)

However during the installation I encountered Error Code: 80073712
I tryed the installation again without anything else open and still the same result
I tryed the installation again having restarted and still the same result
I tryed the installation again after running the DISM Tool and still the same result

Yesterday (17/7/15) I tryed to download another important update:

1) Security Update for Windows 8.1 for x64-based Systems (KB3004365)

However during the download I encountered Error Code: 800F081F
I tryed everything that I tryed previously and still the same result

I searched around and both of these error codes apparently mean that a file needed by Windows Update is either damaged or missing

I thought I might as-well start a thread about it on these forums as not being able to download/install security updates isn't a good thing

Please Reply!

More replies
Relevance 46.74%

Hello,

I have problem with (wired) ethernet interface in my Satellite Pro U300. I have to use it in many places (office, home, clients) and when I restore from standby or hibernation the ethernet interface shows that the *cable is disconnected*, despite cable connection *is* connected and works perfectly with all other devices, laptops and PCs.

The switch also shows that the there's no link signal. But to re-activate malfunctioning ethernet port it's enough to turn off the ethernet interface and then after 5s (1s is too short!) turn it on.

Then a baloon window in traybar shows that there's 10 Mbps link, but in fact, link works at 100 Mbps (I can see it in connection status window and on ethernet switch LEDs). It's the only laptop that has such problems.

I have latest ethernet driver 5.664.205.2007 installed on Win XP SP2.

Is there any chance that I'll get rid of turning off and on ethernet interface few times a day (apart from changing laptop)?

Answer:Satellite Pro U300: Error message: cable is disconnected but Lan cable is connected

Hi

I don?t have a real solution but I?ve got some solution proposals?

First of all you should check in the device manager if the LAN card was recognized correctly. The Ethernet card should be listed under Network adapters without any yellow exclamation marks.

If the LAN card was recognized correctly then the next step should be the checking of the Local Area Connection properties.
There you should check the TCP/IP protocol properties.
The settings like ?Obtain IP address automatically? & ?Obtain DNS server address automatically? should be marked.

Greetings

4 more replies
Relevance 46.33%

Hello,

Since last night, my LAN connection has been giving me the error "Network cable unplugged." I have tried swapping the cable with another, swapping the ports on the router, restarting the router, power cycling the router, turning off the router and my computer and then turning them back on, and nothing has worked.

My computer has two network connections: Realtek PCIe GBE Family Controller and a Hamachi network, which the computer is using (but not getting Internet on, of course) - I assume because it isn't giving a network cable unplugged error. This is the network controller that comes on my Gigabyte MA790X-UD4P motherboard, and it has the latest driver from the manufacturer's site (7.6.820.2009). In the device manager, it says that the device is working properly. There is a green light under the ethernet cable on the router, but not where it attaches to the motherboard (I can't remember if there was one before or not, though).

The Realtek Diagnostics Tool says the following:
IP Address 0.0.0.0
Connection NAme: Local Area Network
Link Status: Disconnected

It has a tab for Cable diagnostics, which says the following (Pair/Length/Status):

1-2 0 Normal
3-6 115 Normal
4-5 0 Normal
7-8 191 Short

When I run diagnostics, Register, Mac Loopback, PHY Loopback, IRQ, and FIFO all pass.

Here is what ipconfig/all says:

Primary Dns Suffix . . . . :
Node type . . . . .: Broadcast
IP Routing Enabled . . . . : No
WINS Proxy Enabled . . . . . : No

Ethernet adapter Lo... Read more

Answer:Network Cable Unplugged error: cable is plugged in

  
Quote: Originally Posted by sodivided


It has a tab for Cable diagnostics, which says the following (Pair/Length/Status):

1-2 0 Normal
3-6 115 Normal
4-5 0 Normal
7-8 191 Short



Have you tried a different network cable? Your diags here say you have a short on 7-8.

3 more replies
Relevance 45.51%

I'm having a tough time diagnosing an issue a colleague of mine is having. Basically the problem is that whenever this user plugs in a LAN cable his computer would blue screen with the error 0x40000080. After analyzing the crash dump all signs pointed to "e1e5132.sys" driver for Intel® PRO/1000 Adapter NDIS 5.1 deserialized driver. A quick google search revealed a lot of other systems experiencing the same problems so we decided to install the latest drivers from both Lenovo and Intel as the system was previously using Factory Image software. The updates had no bearing on the blue screens as it continued to occur so we tried to re-install the operating system "Windows XP Pro" and saw the same problem creep up. This machine is a Lenovo T-61 so we contacted Lenovo and they replaced the system board citing bad hardware. The next day the same thing happened, in fact it happened to 3 machines within the same department who were all purchased in the same bulk to the best of my knowledge. This user was so frustrated that we switched him out with a brand spanking new Lenovo T-61 right out of the box. The only remains from his old systems were Documents copied over and E-mail .pst files. About a day later "Boom" blue screen again, same culprit according to the Minidump. I want to think there is some files on the system that possibly got copied over that were corrupt but frankly I'm running out of options on this one.I would appreciated some assistance... Read more

Answer:Stop Code Upon Plugging In Lan Cable

Read This...and specifically, make certain to follow These Requirements.Post back and let us know if you are now able to connect to the LAN without the bsod. Thanks!

2 more replies
Relevance 45.1%

 Product Name: HP ENVY 15-j059nr Quad Edition Notebook PCOperating System: Microsoft Windows 10 (64-bit)Excused me!I have forgotten my ENVY 15's BIOS administrator password.This is the code it shows after 3 times of typing the wrong password:18874377 Could you give me the reset code for this, please?Thanks in advanced.

More replies
Relevance 45.1%

Hello and good morning, I having problems with bsod mostly while playing league of legends but can occur randomly at other times. I have done memtest86, scanned the hard drive, and even took it to pcdirect where there installed a new motherboard but the problem has persisted. Thank you very much for your time.

Just an update a new bsod happened while running the repair option on league of legends.

Answer:BSOD PLaying League of Legends error code 0x0000001e a common code

Hi,

Your Nividia drivers and Nforce networking drivers are causing issues, also some USB issues.


Code:

*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
Use !analyze -v to get detailed debugging information.
BugCheck 1E, {ffffffffc0000005, fffff80002e80b05, 0, ffffffffffffffff}
Probably caused by : ntkrnlmp.exe ( nt!ExpInterlockedPopEntrySListFault16+0 )
Followup: MachineOwner
---------
2: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
KMODE_EXCEPTION_NOT_HANDLED (1e)
Driver Issues:


Code:

Driver: nvlddmkm.sys
Dated: Fri Jun 21 10:06:16 2013
Refers to: Nvidia video drivers.
As you have the latest driver installed, I would suggest Rolling back to the previous version.
If that does not fix the issue, then you may try this newer BETA version


C... Read more

9 more replies
Relevance 45.1%

After poking around on other threads, there's a chance this is related to the hardware drivers. However, I wasn't able to find a thread with this exact error code, so any help on what this means and how to correct it would be appreciated thanks! This is generating on a LENOVO ideapad Y700 series laptop (15 inch).













Solved!

Go to Solution.

Answer:ERROR CODE AFTER A HARDWARE SCAN, RESULT CODE: WVC007002-UM7YSI

Update your Intel Video driver and the false error from LSC should disappear.WVC007002-UM7YSIw=windowsvc=video cardtest 007result code 002um7ysi is a hash code of the serial number of your machine and useless info<unless you chose to send feeback info to Lenovo

1 more replies
Relevance 45.1%

Hi guys, first time posting so apologies in advance if I do something illegal. As far as I can gather, I should be posting in the right forum. I've been having system stability problems for the last week or so. I think it might be because of a mass driver update across my system since nothing else seems to be the cause.

Basically, I updated some drivers bout a week ago and now the PC either hangs or auto-restart when I'm playing games. At first I thought it might be due to OC instability, so I reset my bios to default settings. Didn't quite work out completely as the system still exhibits the "sudden death" during gaming.

Have tried the steps in the sticky above on refreshing the page file. defragging etc. Problem still hasn't gone away. All rams have cleared 7 cycles of memtest at 2.65 volts and 2.6 volts without problems, though everything has been reset to stock already.

My system specs are as follows :
AMD 64X2 4200+
MSI K8N Neo 4 Platinum
2 x 512mb Kingston CH5 PC3200 DDR
2 x 512mb Mushkin Black Line BH5 DDR
Inno 6600GT 128mb
Creative Audugy ZS Platinum
BenQ 1640
Gigabyte CD-RW
Hitachi/IBM 80GB SATA II
Western Digital 240GB SATA HD
Verudium Vortex 430W

Am fairly sure its not a power issue and the core temp never exceeds 49 degrees even at full load. Its about 44/45 idle. Am guessing it might be the soundcard though... Anyone able to help?

Would be most grateful for any assistance and thanks in advance.
... Read more

Answer:system error code Error code 100000d1

Looks like NV4mini.sys is the Nvidia faulting driver... Your Inno 6800GT drivers are at fault
 

4 more replies
Relevance 45.1%

Greetings, I need help solving the error codes below. Thank you

Product: Windows Defender -- Error 1923. Service 'Windows Defender' (WinDefend) could not be installed. Verify that you have sufficient privileges to install system services.

Product: Microsoft Office Enterprise 2007 - Update 'Security Update for Microsoft Office Word 2007 (KB2251419)' could not be installed. Error code 1603. Additional information is available in the log file C:\DOCUME~1\user\LOCALS~1\Temp\MSIfb8e4.LOG.

I hope I have provide useful information to get your help.

Sincerely

Answer:Error code 1923 and Error code 1603

hi, got a questions for ya. have you uninstalled any virus protection software lately? the reason i ask it might of left remnants behind if you did not use the removal tool.

1 more replies
Relevance 45.1%

Hi,can you please help me solve this problem? I've been having problems with my internet connection (works fine on other devices). It takes a lot of time to get started with the connection - it's very slow in the beginning... Thank you!! 

Answer:Lenovo B50-70 hardware scan shows this error code - Result code: WWF00F008-HK0X2L

Hi MacKapu ,
 
Welcome to Lenovo Community.
 
The error code does match possible issue with the Wifi  based on code Windows: Wifi:00F(test)008(result) 
 
Such code thou would be best interpreted by Lenovo tech support team using their tool and your Serial number.
 
It would be best to give them a call for the code 008 (WWF00F008-HK0X2L) result and likewise would be able to advise how to proceed just in case that the WLAN card itself have hardware issue based on the test. 
 
Especially if you have already tried uninstalling and reinstaling drivers for the WLAN card , maximize performance by turning off power management WLAN property and setting to highest on roaming tendency  or even doing complete factory reset aka OKR (everything wiped out but restored to out of the box setting )  . 
 
Note:  
highlights to link  available for further reference
 
Please get back to us on how things would go . 
 
Regards ,

1 more replies
Relevance 45.1%

Attachment 290231
i having problem with this windows update

here is zip for CBSAttachment 290230


thanks!!!

Answer:windows update error (code 9c48 and code 9c57)

You haven't run the CheckSUR tool.

Pleasefollow the WindowsUpdate Posting Instructions and post the requested data

6 more replies
Relevance 45.1%

I am completely stumped by this problem. I will do my best to explain it and see what you fine folks can do.

I had an older bluetooth dongle, off-brand model, 2010-2011 year, that I installed on my new desktop computer. It worked, but sound quality on my Sony Dr-BT101 headset wasn't great. It worked well with my bluetooth-enabled phones and tablets, so I suspected the dongle. I bought a CSR8510 dongle, which came with a CSR Cambridge Radio Harmony software stack. I installed the software, and turned on the headset, paired it, but no sound came out of the headset. I went to Sound, saw no entries. Went to device managers and saw the parts in yellow. I tried to update the driver but all I got was Code 18 error and this weird message in the picture. I clicked on properties and saw this message.





Quote:
The drivers for this device are not installed. (Code 28)

There is no driver selected for the device information set or element.




I am stumped. I've tried uninstalling, re-installing, installing other Bluetooth drivers, waving a magic wand, none of it has worked. I'm thinking it's a problem with the Registry, but I am not sure how to proceed.

Any ideas?

Answer:Bizarre Bluetooth driver problem (Code 18 and Code 28 error)

Give this a try. It's free.
https://www.slimwareutilities.com/slimdrivers.php
You do need to resolve those Other devices category issues.

1 more replies
Relevance 45.1%

I am having the typical black screen. I just want to see if anyone has a resolution to the problem before I have to spend money for a new one. I checked everywhere before I posted for help.

Thanks in advanced. Joe D.

More replies
Relevance 45.1%

I have a HP 522c AMD Athlon 2000+, running windows xp. There is an integrated video card that went bad. So in installed an AGP video card it is a 3D Prophet 4000XT 32 MB. Now that the card is installed when I have it activated there is a code 12 on one of the pci to pci bridges so that my network card in the other pci slots will not work. I have tried the network card on other computers and it works fine, i have also tried the video card and it works fine. I also tried other items in the pci slots while the agp card is in(modem, sound card) and i still recieve the same error. The card works when a pci bridge is enabled but only with the VGAsave driver and with very low quality. When i check the device manager while both pci to pci bridges are enabled, when i can only run the VGAsave driver, it says the there is a conflict under the I/O range with the VGAsave and an Pci to Pci bridge. Any windows updates just delets the pci to pci bridge listed in the device manager. And i have tried all the drivers i could from AMD, HP, Hercules. Any help would be welcomed on how to fix this.
 

Answer:Code 12 in xp on a Pci to Pci bridge, Recieve a code 12 error with video card

your hp box is not only engineered by hp (who tend to focus on low assembly costs) but is an oem build, thus severely limiting your options. a suggested next step would be to attempt to poke around in the bios setup utility and/or to try out a wider variety of cards/slot configurations. good luck.
 

9 more replies
Relevance 45.1%

i keep getting these two error codes every time i try to update these programs through windows update: Update for Windows 7 (KB974332) Update for Windows 7 (KB974431) Update for Windows 7 (KB976098) Ive tried to download these updates from the download centre with out any success. please help me to fix this problem im using is windows 7 ultimate 32 bit

Answer:error Code 800F081F and Code 8024200D with window 7 update

Hello,Some third party programs can affect the Windows Update service. If you are running any third party applications such as Spyblocker, Internet or web accelerators (programs designed to boost the speed of the Internet connection), security or anti-virus programs (Norton, McAfee, etc.), I recommend you temporarily disable or uninstall them and then try accessing Windows Update later. If the problem still happens, try the following steps:Rename the Windows Update Softwaredistribution folder================================================1. Close all the open windows. 2. Click "Start", click "All programs", and click "Accessories". 3. Right-click "Command Prompt", and click "Run as administrator".4. In the "Administrator: Command Prompt" window, type in "net stop WuAuServ" (without the quotes) and press Enter.
Note: Please look at the cmd window and make sure it says that it was successfully stopped before we try to rename the folder. However, if it fails, please let me know before performing any further steps and include any error messages you may have received when it failed.
5. Click "Start", in the "Start Search" box, type in "%windir%" (without the quotes) and press Enter.6. In the opened folder, look for the folder named "SoftwareDistribution".7. Right-click on the folder, select "Rename" and type "SDold" (without the quotes) to rename this ... Read more

2 more replies
Relevance 45.1%

Hi,

Could anyone tell me if there is an updated driver for the TSSTcorp CDDVDW TS-L632H ATA Device? The device is not available as a selectable drive and in device manager it reports the following error:

Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)

I have removed the device and the driver, however on scanning for hardware; vista re-installs the default driver and the same error returns.

Because of this error, I am unable to update the firmware for the drive and the firmware update is unable to see the drive.

Any ideas??

Thanks in advance.

Answer:CD/DVD drive issue on Satellite L notebook - error code Code 39

Hi buddy

What to say?this issue is known and caused by wrong Windows registry entries.
Microsoft has released and published some knowledge articles.

Check this:
http://support.microsoft.com/kb/270008/en-us

First of all I recommend removing the CD/DVD drive from the device list in device manager. Then remove the Upperfilters and Lowerfilters values completely from the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}

Finally reboot the notebook.

That?s all.

PS: you would find this solution also without my help?. You should use the forum search function! It?s helpful!

5 more replies
Relevance 44.69%

Hello all,
I started up my laptop this evening to be welcomed by an unfamiliar message. It continually flashes on a black screen stating:

For Realtek RTL8139(X)/8130/810X PCI Fast Ethernet Controller v2.13 (020326)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM.

I did a little bit of checking into the error through the forums and noticed that there has been a couple posts discussing the possibility of a Hard Drive Failure. However, when I noticed that it mentioned the Ethernet Controller, I was hoping something else would be more appropriate to my current situation.

I would appreciate any feedback on this as i'm unable to get past the message screen. I was able to get into the setup screen and reset the BIOS to it's original setting but this didn't get me any further than before.

Thank you to all for any comments.
 

Answer:PXE-E61 Code: Media Test Failure, check cable

6 more replies
Relevance 44.28%

Just got this result. What does this mean??Thanks!

More replies
Relevance 44.28%

Hi, Trying to install updates to my pc, running win 7 64bit.
Everytime it fails and I get the error codes as above.I've searched the web but cant find a fix to install the 32 updates.

Answer:error code 8000ffff and code 9C57 problem

Have you run the Microsoft Fixit Tool it seems to have worked for some people.

8 more replies
Relevance 44.28%

I can't update at all for the past 2 weeks, I have tried the little cmd tricks, nothing works.

Please help me!

Answer:Windows Update error code # Code 80070424

Same thing happened to me last week. I ended up backing up my important files and doing a fresh install of Windows. It was quicker and easier than all the work I put into trying to repair it.

3 more replies
Relevance 43.87%

Hi there.
Let me start off by saying that my problem is specific to only windows 8.1 64x and deals with usb devices. 
My specs:

Crucial MX100 ssdWin 8.1 Pro 64xMSI Gtx 970MSI Gaming 5 z97i7-4790k
I'm trying to connect my Rocksmith Realtone cable (usb audio) to a usb port on my pc and whenI right click the "Usb audio device) in device manager, this pops up under properties. There is also a yellow exclamation mark on the device.
"
This device cannot start. (Code 10)

The I/O request was canceled."
Now, like I said, this is only on win 8.1 64x. I installed win 7 64x on an older hdd and put it in my pc and the cable was recognized right away and was usable. I have tried:

Manually uninstalling the device, and reinstallingManually installing the device driverFormatted ssd and did a fresh install of win 8.1Tried it on win 7 with same pc and it worked fineUpdated realtek driversUpdated Nvidia driversDisabled xHCI in biosDisabled legacy usb support in diosDisabled eHCI in biosEnabled usb powered hubs in biosDisabled selected powering in power options + made a new high performance profile
Here are photos of the problem
http://puu.sh/gPfLJ/73044b5afe.png
http://puu.sh/gPfNm/9e63769f7d.png

Every other usb device I have/try works. I tested all my usb 2.0 and usb 3.0 ports and they all work with my mouse, keyboard, and flash drive.
I'm not really sure where to go from here. I contacted Ubisoft (maker of the game Rocksmith) and they said it was a... Read more

Answer:This device cannot start (Code 10) with Rocksmith Realtone Cable (USB Audio)

Well I formatted my ssd and installed Win 7 64x Pro on it. Firs thing I did after updating GPU drivers was plug the cable in, and lo and behold, it worked instantly. 
I think it has to do with the fact that Microsoft made the drivers for USB ports for win 8.1, as opposed to how Intel made them for win 7. But, this is just a speculation

17 more replies
Relevance 43.87%
Question: Rs232

I am planning on building a small form factor PC but it will need RS232. I don't know for sure if there will be room for an add on card for the RS232. Is there a usb to RS232? If so, will it work as good as an add on card?
 

Answer:Rs232

Usb to RS232 adapters/cables are common (on Ebay) and I assume they work well but I have never used one myself.
 

3 more replies
Relevance 43.87%
Question: RS232 on TV

RS232 on TV and Freeview Sat box. What is this serial port for?

Answer:RS232 on TV

Dunno about the TV. But my Humax Freeview STB has serial connection which can be used for uploading firmware upgrades from PC (after first downloading from Internet). Although the upgrades are available over the air, they are available sooner off the Internet.For this to work, one requires (for my box) what is known as a Null Modem Cable (and, of course, a serial connection on your PC). Cables avaialble on ebay, maplin etc.If you haven't got a serial connection on your PC, you can get a USB to serial adapter.It should all be described in your manual.Maybe the TV can take firmware upgrades in a similar way.

2 more replies
Relevance 43.87%
Question: USB - RS232

On my old pc i used a belkin ups with their bulldog software. The ups connected to the pc via a serial cable and all worked very well.So I buys a new pc and realise that it doesn't have a serial port. So I get a USB- RS232 cable (serial connector one end to connect to the ups and a USB conector the other end).I installed the drivers from the disk that came wit the usb/serail cable but the ups is not detected. Interestingly if I go into device manager, after installing the driver, and expand the tree so that i can see the driver one minute its there the next the device manager tree closes then opens and the driver disappears then it re-appears!My operating system is win xp home sp2.

Answer:USB - RS232

TomGI've used usb-serial converters, not all with the same degree of success. In most cases however, a reboot seemed to cure most ails, and sometimes only with the usb converter connected before boot up. Not a lot offer, but might be worth a try if you haven't already...

10 more replies
Relevance 43.46%

Admin password or power on password1st is how do I disable it all together?2nd thing I need system disable code # 54575104

Answer:System disable code error code

@Shuwat66? Please enter            41453120 Regards.

2 more replies
Relevance 43.46%

I am unable to install Windows updates as I get an error " Code 64C : windows update encountered an unknown error..
Same with Code 66A
Please help.
I am unable to also install Windows Live essentials
I am using Windows 7
Greg

More replies
Relevance 43.46%

Error Code C00D1199 (aka: code 80040265) is an error message that can be displayed in several different ways and can be worded different as well, but it all refers to this error message originally posted as message 80040265.

There were a few posts on here about them, but many of the threads seemed to be closed. I just noticed that I have gone through all of the motions and really tried, but no pickle here....well, there might be a pickle, but it is the kind of pickle you get stuck in and is not cool whatsoever.

Here is what I have done:

1. Made sure that the format was supported with windows media player. It was, as it is an .avi, so no problems there.

Here are the types that are compatible:
.au and .snd
.aif, .aifc, and .aiff
.cda
.vob
.jpg
.swf
.dvr-ms
.mp3 and .m3u
.mpeg, .mpg, .m1v, .mp2, .mpa, .mpe, .mp2v, and .mpv2
.mid, .midi, and .rmi
.avi and .wav
.asf, .asx, .wax, .wm, .wma, .wmd, .wmp, .wmv, .wmx, .wpl, and .wvx
.wmz
2. I made sure that other .avi's I have in my collection were working properly with the WMP (Windows Media Player). They were, just not the ones I was trying to fix, of course..

3. I made a sandwich and drank some Yoohoo.

4. Installed a sturdy set of codecs with DivX to ensure that that was not it. I know I had to do it before, but I recently cleaned and started my PC from scratch again, so the previous codecs were not there.

5.Made sure all of my audio devices and drivers were updated and installed properly-for the most part-which I ... Read more

Answer:Error Code C00D1199 (aka: code 80040265)

Welcome Miss Haley, have you read through some of the suggestions here? They seem to have some detailed info on the error code C00D1199 (aka: code 80040265)
http://www.updatexp.com/c00d1199.html

I use the free "Jet Player" and love it - whether it's movies or music - there's not much it won't play or burn, (runs circles around WMP)
http://www.jetaudio.com/download/
Hope this helps
 

1 more replies
Relevance 43.46%
Question: wireless rs232

HelloDoes anyone know if it is possible to transfer data wirelessly via a rs232 connector on a Win95 laptop to another Pc with either Win95 through to Xp?Thank You!

Answer:wireless rs232

click here

4 more replies
Relevance 43.46%
Question: RS232 problem

This is for the really old hands...

Got this Seiko labelprinter on Com4 (hispeed pci serial card).
My mobo is Asus P5Q3 wifi-ap deluxe.
I am always on a hell of a ride before I get this to work, these are the options shown in device mgr.:
bps 9600...115200 (several tried)
databits 8
parity none
stop bits 1
flow control none/hardware/xon-xoff (think hardware was the control of choice when it at at last worked for prior W7 installs: Beta, RC, W7)
Com 4

Msg "printer communication error".
Only possible setting on the printer is the com port.

Now I can try for days changing this and that and maybe as before it starts to work "just like that", but it is annoying: I had a crash and reinstalled W7 Ultimate.

W7 gives me a choice of two universal drivers, V8 and V10, tried to change to V8 but that doesn't change anything.

Anyone?

Answer:RS232 problem

Normally you don't need to change settings on the port itself. I would look towards a driver issue here (check for drivers for the printer itself that are comparable with W7)

4 more replies
Relevance 43.46%
Question: RS232 vs. Parallel

While working on a larger problem I found I was not quite sure of the port and cableling names. Is DB-25 RS232 the same as a Parallel port? Also, What is RS422 and RS485.

I know that DB-9 is RS232 and a serial port, so I assume that DB-25 RS232 is simiar to a serial port but I think I may be getting it mixed up with a standard Parallel port as well.

I had found one site but it was too technical for what I need to know. I just want to know an example of it's purpose and what type of connecter they use.

If someone could straighten me out on all this it would help me a lot.

[in case your wondering about the larger problem...it involves Punch Press machines, controls, and a BTR board. It seems most BTR's use a serial (DB9 RS232 connection) but ours uses what I am calling the parallel port]
 

Answer:RS232 vs. Parallel

6 more replies
Relevance 43.46%

Hello,I've got a plotter (well, it's a vinyl cutter), which is serial and according to the manual the pin-outs are as follow.It looks to be as if they put '1' for RTS when really they meant '7'. However, that aside, is this a standard straight through cable because TX/RX are not crossed but I thought if it were straight through then 4/6 and 7/8 wouldn't be linked?I'd rather just buy a cable, but this layout is confusing me Thanks for any help in letting me know about this layout.

Answer:Help with 9 pin RS232 pins.

Early serial connector layouts  were defined by the computer maker.  If that was they way they did it, that was the way it worked. Standard layouts became standard later.The layout you show in the picture is not exceptional at all.Here is another almost the same.http://www.diyha.co.uk/electronics/comm1.htmlAnd with photoshttp://www.google.com/search?q=9+pin+serial&hl=en&client=firefox-a&hs=yHq&rls=org.mozilla:en-US:official&prmd=ivns&tbm=isch&tbo=u&source=univ&sa=X&ei=Sc7LTbDjKZO4sAObjqToBg&ved=0CDIQsAQ&biw=853&bih=372I like this one:

3 more replies
Relevance 43.46%

How do I determine if the USB port is actually getting data to/from the system's COM port?

Some info:
- I have Vista Home Premium
- I purchased a Generic USB to RS232 adapter (from China) based on a PL2303 chip.
- The driver that came with the adapter seems to have installed properly.
- I have RealTerm installed.
- I jumpered Tx to Rx plus other pins on the male DB9 connector.
- I sought help from Prolific (re PL2303), but found nothing helpful.

But I don't know how to look for data passing through the adapter. What I type on the keyboard does not show up on the RealTerm screen.
I've worked with RS232 for years, and know about the signal-type on the USB port.
But now I am stumped, and about to cut the vinyl covers of the adapter.

More replies
Relevance 43.46%
Question: RS232 connection

Not strictly a computing query but I just got a new LCD TV and it has an RS232 connection and so does my sky box. Can anyone tell me anything about it.

Answer:RS232 connection

It's generally used by factories and engineers for setting and controlling the user interface modules (menus) you see and use on the tv.

3 more replies
Relevance 43.46%

Hi
i bought a cheap usb to rs232 cable of ebay for 2 with a driver disc.

When i connect usb to port the wizard takes over and asks to install disc but then it will not install .
Have downloaded different drivers but it still wont work,drivers are on desktop i think
thought cable was not working so ordered another but same problem.
Am i doing something wrong?
 

Answer:usb to rs232 problem?

Some manufacturers of converters like this require you to install the driver software before connecting the converter to the computer. I would suggest going into device manager and uninstalling the converter, restart the computer. Hopefully on the driver disk there is a "setup" or "install" utility that can be executed, run this install and after it is done connect the converter to the USB port on the computer and let the New Hardware Wizard do its thing. If this doesn't fix the problem try a different vendors converter.
 

1 more replies
Relevance 43.46%
Question: RS232 Question

I am planning on building a small form factor PC but it will need RS232. I don't know for sure if there will be room for an add on card for the RS232. Is there a usb to RS232? If so, will it work as good as an add on card?
 

Answer:RS232 Question

Check out this link: TRENDnet USB to RS-232 . I do not personally own one, but I have used them at my job and they seem to work pretty well. You may have a driver issue, depending on the OS you will be using, but for the most part it works.
 

5 more replies
Relevance 43.46%
Question: Wireless RS232

I need to extend a fiber optic connection one-half mile LOS. The fiber carries RS-232 data. Can anyone recommend a hardware solution?
 

Answer:Wireless RS232

While I haven't used them myself, this might help:
http://www.bb-elec.com/product.asp?sku=9PFLST&dept_id=101
 

1 more replies
Relevance 43.46%
Question: rs232 transmission

I am trying to connect windows xp com 1 to a wire edm machine rs232 port
machine receives in msdos. tried using hyper terminal. Program shows it sends but it is not received by the wire machine.
 

More replies
Relevance 43.46%
Question: RS232 data

Anyone know what software is best to use to enable me to view the data coming into my RS232 port from external scientific equipment?...ie an anemometer!....I need to view the raw data to check why I do not get the correct readings from the equipment and been told I should do a port scan...bit too techy for me!
 

Answer:RS232 data

9 more replies
Relevance 43.46%
Question: Pavilion 550 RS232

Hi, I would like to buy a HP Pavilion 550-209nl Desktop, but I have a couple of issues:Is it possible to add a RS232 connection on it? I need it to connect some instruments at work.Is it possible to use with two screens? Cheers Ale

More replies
Relevance 43.46%

Hi allI am thinking of buying a new lap-top (nothing fancy) but I note that none seem to have an RS232 port any more.I MUST have RS232 because one use of the laptop would be in communicating with all sorts of strange devices that use RS232 (using all sorts of software).I know that USB to RS232 converters exist BUT now to the question:One piece of software I use is Hyperterminal and it "looks" for ports (eg RS232), but as far as I can tell, doesn't see USB (my son's laptop only has USB, and Hyperterminal only comes up with TCP, modem and COM4 (IIRC) which is the infra-red port). And all the other software (i.e. other than Hyperterminal) just seems to find COM1 and then works.Thus, does anyone know how all these RS232 bits of software could find the "port" via USB? Would the USB to RS232 converter cable have software that turns USB into COM1?Has anyone used stuff like Hyperterminal via USB?Thanks for any help.Skeletal

Answer:RS232 on new laptops

Is it a Basic Com port

10 more replies
Relevance 43.46%

Hi guys

I purchased a HL USB RS232 (serial to USB adapter) and the drivers that came with it are not being detected by windows 7. Would anyone happen to have a link where i could find a working driver for Windows 7.

Thanks

Answer:HL USB RS232 driver

have you tried loading the drivers in compat mode ? Compatibility Mode

9 more replies
Relevance 43.46%
Question: rs232 transmission

I am trying to connect windows xp com 1 to a wire edm machine rs232 port
machine receives in msdos. tried using hyper terminal. Program shows it sends but it is not received by the wire machine.
 

Answer:rs232 transmission

Hi, You might want to check and see if the machine receiving the data and the computer is set the same. (Data Bits,Parity, Protocol, Speed, Stop Bits, and Handshaking) They have to match on both or it will not work.
What DNC software are you using and what control is on the machine?
I might be able to help you better if I know that.
 

3 more replies
Relevance 43.46%
Question: RS232 port

I have just bought new software for my laptop, it's for diagnostics on cars. The software has been configured to use a rs232 (db9) socket on the laptop to conect to the OBD2 on the car, the only thing i have on my laptop is USB's and the 25pin printer port. Is there a way around this?many thanks.

Answer:RS232 port

USB to Serial Port connector?

9 more replies
Relevance 43.46%
Question: No RS232 support

First, I appologize for this being so long-----I have a laptop I was given to use at work that is dual booted into Windows 98 and XP Professional. The Windows 98 is being used for the DOS architecture only. It is not a full operating system setup. I use this DOS for operating a data acquisition machine. However, this new laptop does not have an RS232 port for the DB9 adapter cable that is on the data machine. What I am trying to do is to use a USB conversion cable as this laptop has many USB ports. I know I need a USB driver for this to work. I went to the adapter's webpage and downloaded the driver for Win98 (as there is no driver support for DOS). Here is my dilemna: being that Win98 is not a full operating system, the driver will not load. Is there some way I can manually place the driver in config.sys and autoexec.bat in the DOS architecture. I have tried many configurations that did not work. Unfortunately this data system has to run in DOS only.

Answer:No RS232 support

No.It would have to be a driver written specifically for DOS to work properly.

8 more replies
Relevance 43.46%

I am trying to make an application with C++Builder which communicates with a PIC16F877A which has a RS232 interface. Unfortunately my computer only has USB ports so I have bought a USB to RS232 converter cable.
Well I am a complete beginner to C++ Builder so really at this point I don't even know it will be possible to do this... Any help and advice would be really appreciated. ies
 

More replies
Relevance 43.05%

Symptom:
The URL of a shared folder on the LAN,  copied into Windows Explorer address bar produces the Network Error in the above title.
Network Error: WIndows cannot access
\\server.LAN.com\MySharedFolder   Error Code: 0x8004005 - Unspecified error.
But from a Dos terminal, Windows Explorer can open the same location just fine.  From DOS terminal:
start

More replies
Relevance 43.05%

Hello

I need your help to find an USB adapter to connect to and Old Laptop that only have RS232 port.

I want to connect USB divices to the RS232 based Laptop

Thanks for your Help

Humberto Medina

Answer:Old Laptop with RS232 needs USB ports

pcmcia card to usb is ok

1 more replies
Relevance 43.05%

I have an old trusty 2000VA UPS that has an RS232 communications port and I wonder if there's some way I can get Windows 7 64-bit to see the UPS via a USB converter cable. This UPS does not come with any Windows 7 driver or management software, Is buying a new UPS the only way forward if i want to protect my ASUS Republic of Gamers Core i7-3770K @ 4.6GHz machine?
 

Answer:UPS USB-to-RS232 Converter and Windows 7

The UPS doesn't have to be connected to the PC via USB or serial to protect it so you can use it as is.

Buy it will likely work for management with a USB to Serial adapter, Windows 7 has built in support for many APC UPS's out of the box. You may also find newer APC software for your model on the APX website.
 

3 more replies
Relevance 43.05%

Is there anyway to control Media Center via RS232?

Thanks

More replies
Relevance 43.05%

Hi, Ive purchased a USB To Rs232 cable to run on my laptop running Vista Premium 32 bit, but for some reason I cant find the correct drivers for it,the ones ive found are only for XP thats if there is one? if anybody has done this could you please let me know how it's done. Thanks

Answer:USB TO RS232 vista drivers

Make, model of lapy and the cable?

7 more replies
Relevance 43.05%

I would like to reprogram a EEPROM, however it seems that my Serial Port does not provide power when I enter Windows XP. Under Linux, the JDM PIC programmer's LED lights up, however I need to use Ponyprog in Windows. I see there is power to the programmer just until I enter Windows. Any ideas? Thanks





T61p T7500, Quadro FX 570M, 4GB, 60GB Patriot Pyro, XP ProX61t Tablet, L7300 Centrino vPro, Windows 7 Home 64-bittpfancontrol installed on all systems

Answer:RS232 in Windows XP with PIC programmer

Hello mate, Try to see in the device manager if windows does not turn off the port to save energy.It's the only option I see for the moment. I try to look further if it's not the problem.





__________________________________________________________________________________Knowledge is of two kinds. We know a subject ourselves, or we know where we can find information on it.ThinkPad T510 4313-CTO Windows 8 x64 - Intel Core i7-620M - NVIDIA NVS 3100M - 8GB RAM - 240GB SSD- Intel Centrino Ultimate-N 6300 - Gobi 2000.ThinkPad Helix 3697-CTO Windows 8.1 x64 - Intel Core i7-3667U - Intel HD Graphics 4000 - 8GB RAM- 256GB SSD - Intel Centrino Advanced-N 6205 - Ericsson C5621gw

5 more replies
Relevance 43.05%
Question: RS232 on M72e Tiny

Hello to All, On specifications M72e Tiny (MT - M 3267 - 5B1) it is said that on the motherboard there is a COM (RS232) port.If this is just how to activate and what is the connection of the latter? Thank you in advance for your answers.Cordially.

Answer:RS232 on M72e Tiny

Hello,Person for an answer?This becomes very urgent for our production.Thank you in advance.Cordially.

6 more replies
Relevance 43.05%

I have the problem that my RS232 work not 100%under MS/DOS. In Windows XP the RS232 works fine.What can i do ?

[email protected]

Answer:Tecra Series S2 and RS232 under MS/DOS

Hi,

I think you need an adequate DOS driver for the RS232 port!

At http://newsletter.toshiba-tro.de/main/index.html you can ceck which hardware your Tecra S2 have an search a driver for it at the web!


TOK

1 more replies
Relevance 43.05%
Question: RS232 line drivers

Anyone had any experiance with these?I want to send (only) from a PC to some machines about 50 yards away. I need to do it using only one line driver at the PC. I have looked at the Patton website (model 1000) but it is not clear if I can use just one, for sending only, or MUST these things work only as pairs?

Answer:RS232 line drivers

click here for detailed information on the RS232.

2 more replies
Relevance 43.05%

Does anybody know if a RS232 port is the same as a serial port?
 

Answer:RS232 the same as serial port?

Well, I think so. Just do some google image search on "Serial port" and see if that's you mean.
 

5 more replies
Relevance 43.05%

Hi, I need RS232 pinout of HP RP2 Retail System  2030 . How can i found it ? { RJ-50 Serial Ports (Power Configurable 5V/12V) } Could you please help me ? Best Regards, N A

More replies
Relevance 43.05%
Question: RS232 serial port

Does the HP Probook 650 G1 Notebook PC come with a built in RS232 serial port. If not is it an option. If it is not avaiable is there a model with the RS232 port built in or available with an option.

More replies
Relevance 42.64%

i have not been able to solve this one for a particular user.

skydrive pro stopped syncing. it produces the error in the title. i did some googling and followed a few fixes with no luck. due to some other office issues, i wiped his machine and reinstalled windows. with a fresh install of windows and office 365 he is still getting the error when syncing skydrive.

does anyone have any idea how to fix this?
 

Answer:Error code=0x80004005; Error source=Groove __ Microsoft SkyDrive Pro Error

1. Clear all browsing history on IE
2. Stop syncing all Skydrive Pro folders (have the remaining folders moved away from the original location to avoid duplicate renamed folders)
3. Run IE as administrator and resync the libraries normally

Those are the only instructions I found that made sense.
 

3 more replies
Relevance 42.64%

I have a need for an RS232 port probably PCI, but I see such a wide diversity of prices. Which should I choose? Some have a UART and some do not. Do I need a UART? Thanks, Jim

P.S. I'll be using it with ham radio software called Ham Radio Deluxe (HRD) and a ham radio transceiver Yaesu FT-950

Answer:Adding an RS232 PCI port to my desktop

Check to see if you have a PCI slot. Some newer PC's only have PCIe slots and if they have a PCI slot it is a "bridged" slot to the PCIe bus and many PCI devices will not work or work properly on a bridged PCI slot.

I would check and see what others with that software are using.

(ex W5DVO/ZD8JES).

9 more replies
Relevance 42.64%

I have a set of scales that outputs data on rs232. I need to read the data (weight in grams)multiply by a price per gram and output to a rs232 LCD display.Is there an easy way to do this. the scales constantly output and the price per gram has to be adjustable

Answer:RS232 data converter and output

Easy is a relative term.Most scales like that are used in some company or way that demands some software in order to be sold. Look at the makers web site for how they expect you to use the product. We still have many running a DOS app.1/3 of highway deaths are caused by drunks. The rest are by people who can't drive any better than a drunk.

2 more replies
Relevance 42.64%

wont print on rs232

Answer:tm-t88iii rs232 wont print

http://www.pos-printer.com/epson_tm...does it have Windows 7 drivers ?? I was under the impression Epson stopped support at XP ?

2 more replies
Relevance 42.64%

Hello, so I bought cheap usb to rs232 cable off ebay and been trying to get it working. I tried installing many different drivers from internet and still windows is not recognizing my cable. I tried to copy drive file to system32\drivers, no luck.

Has anyone else had similar problem? Do I need to buy prober cable with driver cd included?

Thank you

Answer:Usb to serial rs232 no working drivers

You need a Prolific PL2303. Its the ONLY one I've found that will work with my wife's Singer Embroidery machine. It works on both Win 7 and Win 8.

Amazon.com: Plugable USB to RS-232 DB9 Serial Adapter (Prolific PL2303HX Rev D Chipset): Computers & Accessories

1 more replies
Relevance 42.64%

Hello Techguy
I have a USB to RS232 converter which came with a driver disk. I can load the driver in and everything seems to load OK. However, when I then plug in the converter, it can not find the driver.

What it seems to be looking for is a driver called "USB2.0-SER!". However, the device seems to be a Prolific chip device and I would have expected to see it looking for something like "PL2303" or similar. I searched the computer for a driver with this name but no luck.

I went to the Prolific website and downloaded their driver but that didn't work any better.

I know these devices work as I have seen them working on other computers. How do I get it going?
 

Answer:Solved: Driver problem for USB/RS232

6 more replies
Relevance 42.64%

I have purchased a usb to serial adapter but the drivers are not functional.

Every time I plug the cable inside my computer i get a USB device not recognized message. Under device management > Universal Serial Bus controllers > Unknown Device.

The drivers that i have is called "PL-2303 Driver Installer". Even after installing this driver, I still have no luck. I know it is possible to update the driver but the driver format would have to be in a .INF file. In this case the driver is a .exe file so i have no idea what to do.

Any help would be really greatly appreciated also the drivers are available @ http://www.prolific.com.tw/eng/downloads.asp?ID=31

If the device is functional and installed, it should be under the COM ports in device manager but like i said before it is not and is listed as "Unknown Device".
 

More replies
Relevance 42.64%

Dear Friends;
We have many software installed in Laptop having WXP for trouble shooting purpose at machines. Communication of many devices is done through RS232. Some time it happen that a we fail to communicate with a device while everything is ok because some other software has already captured RS232 port of Laptop and it is hard for me to find out which software has done that.
Yesterday, after making communication with a PC via two soft wares, I tried to hibernate the PC but it failed to Hibernate as Com port was busy/captured while all the programs were closed. Is there any way to know which program has captured the Com port?
 

Answer:How do we know which program captured RS232 port??

I have used Portmon with XP 32 bit: http://technet.microsoft.com/en-us/sysinternals/bb896644.aspx
I am not aware of an equivalent utility though for 64 bit XP.
 

2 more replies
Relevance 42.64%

Here is the deal. Where I work we have a ticketmaster application that uses a seperate RS232 network. This means special lines that run to a special little ticketmaster box in my switch room. Needless to say it is a royal PITA when we have to move these computers connected to this special network.

So to fix this I was hoping there were some kind of RS232 to ether net adapters out there. I know they exist, but I think the solution I need is special. i need an Adapter on the PC side that talks to an adapter on the switch side. So basically the flow would go like this:


COM Port --> Convertor Box --> Ethernet --> Converter Box --> Com Port on Special Box

Anyone have any suggestions?
 

Answer:Piggy Back RS232 Over Ethernet

Is it realy Ethernet or justr cat5. (meaning is there going to be a ethernet switch in between?)
 

6 more replies
Relevance 42.64%

Since installing SP3 to my Windows XP Pro system my RS232 serial port no longer works. I have a Hyperpen tablet that has an RS232 connection so it no longer functions. Is there a converter that I can attach to the male RS232 so I can connect via a USB port? I have seen a USB 2.0 to RSB (male) serial adapter dongle but that is of no use. I'd appreciate any suggestions towards resolving this.

Answer:RS232 serial port not working

Have you checked in Device Manager to see if it is working there , or if there any conflicts . It won't have just broken , it must be a software problem as it occurred as you loaded SP3 , it might just need reconfiguring , what does the tablet need in terms of port speed etc. , data bits , flow control etc. ? Ashley

7 more replies
Relevance 42.64%

is a RS232 port the same as my 9 pin com port?if I wanted to make software ROMs for my 8-bit bbc micro, what would kind of eprom programmer would I use?I'm a complete n00b in this field.

Answer:RS232 port & eprom Programmer

try an emulator to save the grief......Link:>http://www.emulator-zone.com/

2 more replies