Computer Support Forum

Re-installing win8 with bitlocker encryption enabled on old OS.

Question: Re-installing win8 with bitlocker encryption enabled on old OS.

New to this forum, and this is my first thread. Please provide me with some help if possible.

So my problem is the following: Kept getting BSODs from some driver inflicting with ntkernel according to whocrashed and bluescreenview. Anyways, disabled my network card as I thought that was faulty, updated all my drivers and checked my ram with memtest just to be sure. Was still getting the BSODs.

Decided to use driver verifier to see which driver that caused this. Bad idea. Turns out that one of the drivers indeed was faulty, but now I'm getting blue screen before I can even log in to windows. Tried to boot into safe mood a thousand times by repeatedly pressing F8 and shift+F8 to no avail. Thought that I then could turn of driver verifier from the command prompt, but No! (Since if I could turn this of the BSOD before system start would then stop since the purpose of windows driver verifier is to force the faulty drivers to create BSOD).

Then downloaded EaseUS Recovery Essentials to see if that could help. Turns out that my ENCRYPTED (bitlocker) which my operating system is on, can't be found because I'm assuming that the change in boot order previously when running memtest disabled it.

Now had to find my win8 installation CD to force it into safe mode alternatively to re-install it, but to no avail. It says that the hard-drive is still locked even though I've got the key in a USB stick attached to the computer and even though I manually put in the recovery key. Was now to give up on fixing this and tried to do a clean install on the SSD drive, but then it says that "Windows cannot be installed to this disk. The selected disk has an MBR partition table. ON EFI systems, Windows can only be installed to GPT disks." Assume this is because of the bitlocker encryption. So tried to format the drive but it won't let me since the format alternative is greyed out. The SSD with the operating system on is labeled as "Drive Partition 2" and there is another 350mb labeled "Drive = Partition 1:System Reserved" right above it that could be formated. Don't know if that would make a difference?

I'm out of ideas and don't know what to do anymore..

Relevance 100%
Preferred Solution: Re-installing win8 with bitlocker encryption enabled on old OS.

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

Answer: Re-installing win8 with bitlocker encryption enabled on old OS.

Just realized I posted in the win 7 forum instead of the win8 forum. My apologies.

1 more replies
Relevance 91.02%

I am trying to create a Windows 10 image for my organization, and cannot figure out one particular issue with Bitlocker. It seems that after I sysprep, and throw the image on a new computer, it then has BitLocker partially enabled. What I mean is that when going to the About page in System in the settings it shows in red "You need a Microsoft account to finish encrypting this device". The C: drive also shows an opened lock with a warning icon (exclamation point in a triangle).

When going to the Manage Bitlocker page is shows an option to turn on bitlocker. Searching various sites on google has led me to the idea of turning on bitlocker, then turning it off again before sysprep. This does in fact disable BitLocker, however it appears to turn on again after imaging on a new computer.

While it's not a huge pain to disable BitLocker afterwards it does take several minutes to decrypt and multiplied that by many computers does eat up a bit of time in the end. Is there something I'm missing here to make sure BitLocker remains disabled after imaging? These are generally on Microsoft Surface Pro 4 computers that this happens on, it did not do the same thing on an HP laptop I tested.

Answer:Bitlocker Device Encryption enabled after imaging

Bump

1 more replies
Relevance 89.79%

Getting h/w encryption on my laptop has been a bit of a nightmare, but I thought I had it working.... Here is what I did:

Installed M.2 Samsung 850 evo driveInstalled samsung magician, and set Encryption to Ready to Enable.Removed existing HDDRan samsung secure erase from DVD.Installed Win10Installed Samsung Magician (It said Encryption enabled, finally!)Turned on Bitlocker. It did not prompt me for how much of the drive to encrypt, which (I was told) means that it is using hardware encryption of the drive.Added the HDD back.Updated all my drivers to latest versions for my laptop (Asus GL552VW), including Intel RST drivers (14.x)

After doing all that I just noticed that BitLocker is turned off on my C: drive (the m.2 drive)! I looked in Magician and it still says Encryption is enabled. So I went into Bitlocker to turn it on again for the drive. But now it is prompting me to encrypt used space, or whole disk, which means it isn't using h/w encryption.

What am I doing wrong here? Do I need to enable Secure Boot in BIOS? I have read that the Intel RST drivers can cause problems, but I thought that was only with older versions? Is IRST still an problem?

Edit: When I look in the Disk Management took, I see the C: partition of Disk 1 says: NTFS(Bitlocker Encrypted)., But in Bitlocker Drive Encryption tool it says it is off. Manage-BDE -status c: says that there is no encryption. Really confused now.

Answer:Bitlocker turned itself off, Samsung Magician Says Encryption enabled

There are a list of requirements for hardware based encryption here - doesn't look like secure boot is required: How to Enable BitLocker Hardware Encryption with SSDs Helge Klein




For data drives:
The drive must be in an uninitialized state.
The drive must be in a security inactive state.

If the drive is used as a startup drive the following apply additionally:
The computer must always boot natively from UEFI.
The computer must have the Compatibility Support Module (CSM) disabled in UEFI.
The computer must be UEFI 2.3.1 based and have the EFI_STORAGE_SECURITY_COMMAND_PROTOCOL defined.



I only use bitlocker with software based encryption though so can't add to what they say I'm afraid but some of the comments look interesting.

5 more replies
Relevance 89.79%

Getting h/w encryption on my laptop has been a bit of a nightmare, but I thought I had it working.... Here is what I did:

Installed M.2 Samsung 850 evo driveInstalled samsung magician, and set Encryption to Ready to Enable.Removed existing HDDRan samsung secure erase from DVD.Installed Win10Installed Samsung Magician (It said Encryption enabled, finally!)Turned on Bitlocker. It did not prompt me for how much of the drive to encrypt, which (I was told) means that it is using hardware encryption of the drive.Added the HDD back.Updated all my drivers to latest versions for my laptop (Asus GL552VW), including Intel RST drivers (14.x)

After doing all that I just noticed that BitLocker is turned off on my C: drive (the m.2 drive)! I looked in Magician and it still says Encryption is enabled. So I went into Bitlocker to turn it on again for the drive. But now it is prompting me to encrypt used space, or whole disk, which means it isn't using h/w encryption.

What am I doing wrong here? Do I need to enable Secure Boot in BIOS? I have read that the Intel RST drivers can cause problems, but I thought that was only with older versions? Is IRST still an problem?

Edit: When I look in the Disk Management took, I see the C: partition of Disk 1 says: NTFS(Bitlocker Encrypted)., But in Bitlocker Drive Encryption tool it says it is off. Manage-BDE -status c: says that there is no encryption. Really confused now.

Answer:Bitlocker turned itself off, Samsung Magician Says Encryption enabled

There are a list of requirements for hardware based encryption here - doesn't look like secure boot is required: How to Enable BitLocker Hardware Encryption with SSDs Helge Klein




For data drives:
The drive must be in an uninitialized state.
The drive must be in a security inactive state.

If the drive is used as a startup drive the following apply additionally:
The computer must always boot natively from UEFI.
The computer must have the Compatibility Support Module (CSM) disabled in UEFI.
The computer must be UEFI 2.3.1 based and have the EFI_STORAGE_SECURITY_COMMAND_PROTOCOL defined.



I only use bitlocker with software based encryption though so can't add to what they say I'm afraid but some of the comments look interesting.

6 more replies
Relevance 72.16%

I have an older Laptop that operates on  Windows 7 Ultimate,I have the Bitlocker Drive Encryption on and encrypted for Drive C:   I now started the process of encrypting my external usb hdd Drive E: which has a long way to go for it's large
size. During the encryption I needed to disconnect it so I paused the encryption like it says to do before removing or changing any files on it. I then plugged my drive into a newer laptop I have that operates on Windows 10,. I was prompted for the Bitlocker
Drive Encryption Password screen like normal just like on my Windows 7 laptop so I enter the password and it was correct and it began the encryption process again. When I finished with what I needed to do on the Windows 10 laptop I paused the encryption again
and disconnected the drive. I am now back on my Windows 7 Ultimate OS and plugged the drive in, Bitlocker Encryption Password Screen comes up again and I entered my password but now for some reason it's saying the password is incorrect?  "But It's
not incorrect",is there a reason why this has happen and a way to fix it? My second issue is that I have the recovery key written down on paper but on the fifth line of the eight lines that makes the recovery key I left out a number,did not write it correctly,
there for I cannot just reset my password using the key and get back to normal again. Any way to find the lost number to the key? As I do have the rest of it written correctly please help tha... Read more

More replies
Relevance 72.16%

Installing MBAM with SCCM 2007. Normally works fine. On one workstation however...
On SCCM it fails. Without details.
When trying to run C:\Program Files\Microsoft\MDOP MBAM\MBAMClientUI.exe manually the error comes up. "BitLocker drive encryption has a problem and must close. BitLocker will close now. Contact the help desk of your company if you need additional help.
Details: Error fetching the encryption percentage complete."

Any ideas?

Answer:BitLocker drive encryption has a problem and must close. Details: Error fetching the encryption percentage complete.

ERROR: An error occurred (code 0x8004100e):
Invalid namespace

Figured it out...
http://support.microsoft.com/kb/2756402

4 more replies
Relevance 72.16%

Good morning/afternoon/evening gentleman, wherever you are around the globe.

Today, after startup, Windows suggested to me, that I should export my encryption case to some external storage, just in case some bad things happen.

I was surprised, as I haven't enabled any encryption on my laptop.
Or maybe I was wrong, thinking that encryption = BitLocker.

Quick search in Control Panel reveals there is also a setting in User Accounts section named "Manage file encryption certificates".

I haven't enabled encryption in any folder/file using it's Properties window.

So why this "export your keys" option? I don't remember that from Windows 7.

I would be great if someone explained that to me, as I've never used encryption before (since I don't need it).
Also, is cloud storage like SkyDrive/DropBox an appropriate place to store that files?

More replies
Relevance 72.16%

Hi
After rebooting one of our test machines, bitlocker wanted the recovery key.
There were no hardware modifications on that machine.
Error message in event log:
Bootmgr failed to obtain the bitlocker volume master key from the TPM because the PCRs did not match
Event id 24635, source bitlocker-driver
 Each time the machine starts, the recovery key is needed.
Any idea how to solve that issue and why it happens?
update:
Second partition was created manually on that machine. So that's clear that bitlocker reacts...
But now: how can I confirm those changes so that the recovery key is not needed each time we boot?

Answer:Bitlocker enabled drive, recovery key needed during boot, PCS did not match, event id 24635, source bitlocker-driver

Hi,
 
I would like to confirm if BitLocker accepts the recovery key?
 
Please update the BIOS to improve the stability for TPM first.
 
I also would like to suggest you disable and enable BitLocker again to reset the settings.
 
For more information, please refer to the following link:
 
http://technet.microsoft.com/en-us/library/dd835565(WS.10).aspx
 
Regards,
 
Arthur Li
TechNet Subscriber Support
in forum
If you have any feedback on our support, please contact
[email protected]
 Please remember to click ?Mark as Answer? on the post that helps you, and to click ?Unmark as Answer? if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

8 more replies
Relevance 68.06%

bit locker drive encryption failed to recover from an abruptly terminated conversion
i have 2tb segate hd i have stoped  encryption on 94% and shut-down pc now im getting this message 'bitlocker drive encryption failed to recover from an abruptly terminated conversion' while unlocking hd what to do? i will get my data?........please
help me

More replies
Relevance 67.65%

Initially I found that BitLocker on the Go supported removable media like flash drives and external drives. Why isn't a CD/DVD supported since it is considered removable media? Will this support be available in future releases?

Answer:Will BitLocker or BitLocker on the Go ever support CD/DVD encryption?

Hi,
 
Bitlocker to Go is not supported on CD/DVD. Your suggestion is valuable, I will forward this information to the appropriate department through our internal channel.
Both the Microsoft Product Team and Development Team will take into consideration all suggestions and feedback for future releases.
 
Currently, you may need third party software to encrypt CD/DVD.
 
Best Regards,
Niki
 
 Niki Han
TechNet Community Support

3 more replies
Relevance 67.24%

Hi Mr/Ms
I
flash
drive encrypted
with BitLocker 
I used
this
driver for three months my computer is broken I bought a new computer    when i was try my flash disk new computer its give me this  problem 
BitLocker Drive Encryption failed to recover from an abruptly terminated conversion. This could be due to either all conversion logs being corrupted or the media being write-protected
? know my passworrd but I do not know
the BitLocker
recovery key what can i do know pls some one help me 

More replies
Relevance 63.96%

 The windows 10 Pro computer has died, and I would like to put the in my new computer with windows 10 home.   I would like to remove the bit locker password,  so I can reinstall windows 10 pro while keeping my files and apps,  
I'm unable to do this while the drive is encrypted.  How do I remove drive encryption from the drive while I have the drive slaved to a windows 10 home computer? 

More replies
Relevance 62.73%

I am trying to enable BitLocker on a Windows 7 Ultimate x32 system with TPM. I follow the Wizard and when asked to encrypt the drive I select 'Run BitLocker system check' and 'Continue' (see attached sreenshot).
The USB is inserted and contains the recovery key (.txt and .tpm). During reboot I get:

Windows BitLocker Drive Encryption Information
The system boot information has changed since BitLocker was enabled.
You must supply a BitLocker recovery password to start this system.
Confirm that the boot changes to this system are authorized.
If the changes to the boot system are trusted, then disable and re-enable
BitLocker. This will reset BitLocker to use the new boot information.

Otherwise, restore the system boot information.

ENTER=Continue

Windows then continues to start normally. After login I get an error message: BitLocker could not be enabled (see attached screenshot).
When I check TMP it shows as active, initialized and owned.

I've started out from scratch several times - same results. I can't figure out what the problem is.
This is driving me nuts.

Any help appreciated

Thanks

Answer:Bitlocker: BitLocker could not be enabled

BIOS: A06
DELL: d420
Hard drive: System reserved 100MB NTFS, 27.84GB NTFS

TPM
Manufacturer name: BRCM
Manufacturer version: 2.10
Specification version: 1.2
Status: The TPM is on and ownership has been taken

I've since modified the group policy settings for Bitlocker to use a PIN.
I am still getting the same results.
I follow the wizard, select check the system, reboot, enter PIN, get the same "error" messages as shown in my previous post.

This makes no sense.

Any help?

6 more replies
Relevance 62.73%

Trying to start Bitlocker and to encrypt a partition, windows gives me the advices to restart an then comes up with the attached error. Who knows how to fix it?

Answer:Bitlocker could not be enabled

  
Quote: Originally Posted by Henning


Trying to start Bitlocker and to encrypt a partition, windows gives me the advices to restart an then comes up with the attached error. Who knows how to fix it?


Henning hi and welcome

It tells you in the error to use the Bitlocker recovery to verify the drive. Was the drive changed by you? di you have a AV current and running?

Ken

3 more replies
Relevance 62.73%

I am having trouble getting BitLocker enabled. 

The OS is Windows 7 Enterprise and the computer is a Lenovo L512 ThinkPad. I've updated the BIOS to the latest version.  TPM is on.  There are two partitions - System Reserved - 102 MB - NTFS and C - 232.78 GB that show up in Disk Management.
There are two files on the USB, a .tpm and a BitLocker Recovery Key.
When I click on Run BitLocker system check I'm told to insert the USB memory device containing the recovery key.  I do that and see the message that the computer must be restarted. 
After restarting I receive this message:
BitLocker could not be enabled.  The BitLocker startup key or recovery password cannot be found on the USB device.  Verify that you have the correct USB device, that the USB device is plugged into the computer on an active USB port, restart the
computer, and then try again.  If the problem persists, contact the computer manufacturer for BIOS upgrade instructions.  C: was not encrypted.
I've tried the USB drive in every port on the computer with no luck.
Perhaps there's something minor that I'm missing.  I'd appreciate any assistance.
Thanks!

Answer:BitLocker could not be enabled.

I figured out my mistake. 
I had set the BIOS boot order to only HD, as I usually do.  I did not realize that USB drive (now the second option in the boot order) needed to be enabled for the encryption process to continue. 
I've tried the encryption process on two computers, and it worked fine after this.
Thanks for the suggestions.

5 more replies
Relevance 62.73%

Hi there,



I'm evaluating the 90 day RTM of Windows 8 Enterprise and want to to enable full disk encryption (partitions are stock, c:\ only, didn't create any manually). Unfortunately, Windows won't let me. I own a Dell D630 with built-in v1.2 TPM chip. When starting
the system check (just before the start of the encrypting process) I get the following error message:

Bitlocker could not be enabled 

The Bitlocker encryption key cannot be obtained. Verify that the Trusted Platform Module (TPM) is enabled and ownership has been taken. If this computer does not have a TPM, verify that the USB drive is inserted and available.

C: was not encrypted.



I had a look in tpm.msc and the status displays "The TPM is ready for use". While looking for a solution in the web, I came across several screenshots of tpm.msc where the status was displaying "The TPM is ready
for use and ownership over TPM has been taken". Well this relates pretty well to the error message in the first place. 


Technet (technet.microsoft.com/en-us/library/cc754215.aspx) even has detailled instructions online on taking ownership of your TPM module. Apparently, I need to initialise TPM as per the instructions. The problem is, I don't even
have an initialise option available in the right-hand side action menu of tpm.msc.



Well - I thought - if TPM behaves badly then just disable it and follow these Technet instructions ... Read more

Answer:Bitlocker could not be enabled (with/without TPM)

Hi.
This didnt work either, unfortunately... 
However, after deactivating the TPM altogether in BIOS, so that tpm.msc is not even "aware" of an installed TPM chip, I was able to initiate the encrypting process.
Cheers

3 more replies
Relevance 62.73%

Hi 
I am trying to turn on the bitlocker using manage bde by command prompt but it is showing an error 0x80070057 so how can i proceed or fix this problem?

More replies
Relevance 62.73%

How do I encrypt my Extrenal HDD with BitLocker as I don't get any direct options for encrypting the drive?
Also, is there any option to encrypt the drive without formatting because I don't want to lose my data

More replies
Relevance 61.91%

Novice Question, folks...
 
If I have already encrypted my data with BitLocker or some other encryption software, will that render ransomware ineffective?  Or, does it mean my already-encrypted data just gets another layer of encryption (i.e., double-encrypted)?  

Answer:Ransomware vs BitLocker (or any other encryption s/w)

Hi there,If your data is already encrypted then a crypto ransomware would just add its own encryption over the data, making it double encrypted as you said.

6 more replies
Relevance 61.91%

Hey there. I'm having trouble unlocking my external flash drive which was encrypted by me a few months back. It was encrypted using my desktop PC which is not working anymore. I'm trying to unlock it using my laptop.
The problem is, I am entering the correct password but it's marking it as incorrect. I am sure about the password because I had stored it in my phone.

I have a .pfx certificate as well but I really don't know how will it be helpful in unlocking the device. I had saved this .pfx file because while the process of encryption, windows had advised me to save it. Any help will be appreciated. I really need to unlock
this device as the data it contains is irreplaceable.

Regards,
Hannan.

More replies
Relevance 61.91%

I have Windows 7 installed and i use a 4GB memory card for private files. The problem is i used Bitlocker encryption, which was working fine until i installed windows updates. Now this mrning i cannot access the memory card at all. It just says drive not accessible although it does recognise that the drive is there. I have tried system restore which also at the moment will not restore to any point. Can anyone help me with this problem please.

Answer:Bitlocker encryption problem

cant think of anything off hand to help with your immediate problem but for future have you tried the yo-safe feature in win locker in win 7 it gives u drive you can hide so no one even knows its there and even someone who knows abt yo-safe cant get into it as when you open the yo-safe it asks for your password you can make your password the same as your master password when windows starts or you can give it a different password.

1 more replies
Relevance 61.91%

Hi, I have a problem on my laptop. My office laptop is encrypted using Bitlocker as part of our firm's security over our machines and data stored therein. 
One Saturday, I opened my laptop when it got hibernated last friday night after work. At startup, it ask for my password, I entered it but it showed: "Too many PIN attempts". 
I dont know why and how it happened as I did not change my laptops for the last 3 months since it was issued to me. Since its a weekend, I asked some of our IT personnel having their rest days on how to resolve this, they taught to search for the recovery key
in their database using the identifier provided by bitlocker. I found the files recovery keys but no one matched the identifier showed on my laptop's screen (that cant be accessed).
My question is, what if the recovery keys of my laptop cannot be located anymore, are there ways possible where I can still log-in again losing my files? thanks.

More replies
Relevance 61.91%

BitLocker Drive Encryption
i have it in my Control Panel..
is it an unwanted program or something?
thnks in advance~~

Answer:BitLocker Drive Encryption

Bit Locker is a built-in feature of Windows 7 and is completely safe. It's Microsoft's full-disk-encryption implementation. Read more here.

3 more replies
Relevance 61.91%

I am having a hard time trying to figure out what encryption method and cypher strength is used on my Bitlocker to go encrypted portable hard drive.

I understand the settings for Bitlocker are configured in the Group Policy Editor but besides that is there any way to see what level of encryption your portable drive has.

When I encrypted this drive, I left the Group Policy settings default when encrpyting the drive which means the drive was supposedly encrypted using 128-bit with diffuser.

This would come in handy when trying to prove to someone that the device is infact encrypted with either 128-bit or 256-bit.

Answer:Bitlocker To Go Encryption Level

Hello Doc, and welcome to Seven Forums.

If the computer does not have Group Policy included to look at, then you can edit (right click on REG file and click on Edit) the REG file downloads in OPTION TWO of the tutorial below, then check the registry and compare it to the REG file downloads to see how it set. By default, it is set to 128-bit with diffuser in Windows 7.

BitLocker Drive Encryption - Change Encryption Method and Cipher Strength

Hope this helps,
Shawn

5 more replies
Relevance 61.91%

hi hw r u i want to know abt the drive encryption option in windw 7 i used Bitlocker drive encryption to lock or save my drive data(confidential data) frm others. ques is that this encryptn method is right i mean it will damage my hard disk or not . kindly tell me and if u tell me more methods for protection i really appreciate u.thanks

Answer:Bitlocker drive encryption

It will not damage the HDD just make sure you save the "Key" in a save place not on the computer (A hard copy on paper and a digital copy on a thumb drive two backups of the key is best) also the Windows OS partition or HDD can not be encrypted using Bitlocker.

Set up your hard disk for BitLocker Drive Encryption - Microsoft Windows Help

2 more replies
Relevance 61.91%

Hello,
Can someone advise the steps to get Bitlocker installed and working on a windows 7 pro laptop. I just got off the phone with a microsoft support agent who said it is possible with computers on a domain. She
couldn't give me any more info and directed me to technet.
Please share any info you may have 
thanks

More replies
Relevance 61.91%

Hello

Thought I'd ask before I do something stupid
I'd like to encrypt my fileservers with Bitlocker but I wonder how fast it is these days? The servers run Windows 8.1 and when trying on another system I get about 100MB reads and writes during encryption - is this somewhere in the ballpark for performance? Oh and the cpu supports hardware encryption as well

Thanks in advance
Edit:

Just finished encrypting a Raid6 array with 8x2TB drives. Time approximately 24 hours and an average speed of about 125-130MB/sec. Cpu is an AMD A4 5300 dual core cpu. Not so bad imho.
 

More replies
Relevance 61.91%

i use encryption.

what's the diff between Bitlocker and the encryption in windows XP?

xp encryption seems to work fine for me.

Answer:what's the diff between Bitlocker and the encryption

Win7 has disk imaging software and file backup software in most of the versions, both able to be scheduled. Additionally, there is also an included utility to create a restore CD.

Yes, yes, all of these can be had by excellent third party apps but it is enlightening to see MS finally come around and include more required OS-type utilities with the OS itself.

edit: Woah, my response here was to a completely different post, one questioning the need to upgrade from XP to Win7. Either the mods or the OP significantly changed the original post. Normally I am not that obtuse when replying.

7 more replies
Relevance 61.91%

Hi,

I have been having some issues when trying to turn Bitlocker on in C:

I have followed the instructions as per this forum to enable a Startup key in gpedit.msc as I dont have TPM which worked.

After following the instructions, Windows Bitlocker asked me to insert a USB to save the startup key to. This appeared to save and then moved onto the next step where I took down the recovery key etc... and finally restarted to make sure my system was compatible before encryption started.

Upon restart, Windows said that it couldnt find a key on the USB drive. After further investigation I found that windows did not save the key to the USB after all even checked as a hidden file. It will save the text file (recovery key) to usb but not the bek file for the startup key.

I have tried this several times but each time it wont save although the system dosent say there has been a problem and moves on to the next stage.

The USB is a 2gb cruzer with the smart drive software removed and re-formatted to NTFS. I have also tried this on other USB drives with no luck and the USB drives work as Iam able to write other things to it?

Any help would be greatly appriciated as I have searched this forum and MS forums with no luck.

Thanks
Marc

Answer:Bitlocker Drive Encryption using USB

Same problem here. Different USB drives or different usb ports didn't change anything.

Any ideas?

9 more replies
Relevance 61.91%

While using BitLocker Drive Encryption feature, i selected the settings for using the USB to store the security key. But, once I restarted my PC, BitLocker didn't recognized the USB and went into recovery mode.

Can anyone suggest as to why the USB key was not taken into consideration?

Answer:BitLocker Drive Encryption

Windows Vista didn't provided any means by which a user working on Windows XP could access a shared folder of an BitLocker encrypted drive. But, this feature was provided in Win 7 in the form of BitLocker To Go feature.

So, my question is, isn't it hampers the main motive that was behind BitLocker Drive Encryption feature?

4 more replies
Relevance 61.91%

Hi all

bare with me on this, it may sound stupid and have a very simple answer.

I've got a laptop which I currently have Symantec Desktop Encryption installed with C:/ encrypted.
Personally not quite sure if the files it self on C:/ are encrypted or not (I'm able to access my laptop which has the drive encrypted, over the network from my desktop without any issues/error messages to say its encrypted etc)

This is where the possible stupidity comes in. Symantec current has the drive encrypted (Enter password before booting to Windows), but I was wondering if the data it self is encrypted and if not, would it be possible to do this within Symantec (Cant seem to find a way) if not, would Bitlocker be a solution to encrypting the data or will this cause confliction?

On the side as well, I know that Windows has an option to show folders/directories in a different color if they are encrypted, this option is enabled, but none of the directories are coloured, any idea how to get this to work?
Thanks in advance
Josh

Answer:Using Bitlocker and Symantec Encryption

If it said encrypted, it really is. For example, someone detached the hard drive from your system and then inserted that to another computer to read the contents. Symantec will notify a password entry and if there's no recovery key, you won't be able to access it. It works like BitLocker To Go. BitLocker Drive Encryption doesn't need a password prompt if the drive is connected to the original motherboard and there's no changes to BIOS settings or updates AFAIK.

3 more replies
Relevance 61.91%

I m having problems with bitlocker .... my hard drives are not showing in control panel-->system&security-->Bitlocker Encryption drive .... any help related to this please ?????????????????????????????????????????????????????????

Answer:Bitlocker Encryption drives

Make sure you have ALL of the requirements
Hardware requirements for BitLocker Drive Encryption

7 more replies
Relevance 61.91%

can somebody help i use the bitlocker drive encryption and i freeze it in 80% encryption and now i can't access my USB flash drive i try to format it and it's always say "windows was unable to complete the format" my USB flash drive is protect by bitlocker drive encryption when i unlock my USB flash drive in bitlocker drive encryption it's always say "the device is not ready" Please Help ! i want to format my usb flash drive can someone help me??

Answer:Help me !! bitlocker drive encryption

Hello James,

Please perform the following:

1. Download and Save to desktop from this link:
http://go.microsoft.com/fwlink/?linkid=52012

2. Once saved, run the tool. Click on the Continue button, which will produce the report.

3. Click on the Copy button in the tool (ignore any error messages), and then paste into your next reply.

Regards,

2 more replies
Relevance 61.91%

I've got the exact same problem.

I set up the Belkin and Comcast as an unsecured network and everything works. When I try and secure the network and reset everything, the modem won't connect.

It sounds weird but it's correct. The wireless works and the computer connects to it. But the Belkin router will not connect to the internet through the modem, even though none of those settings have been changed.

The "internet" light will show a little activity when I first reset the modem, but after about 60 seconds it goes off and stays off.

I'm going to upgrade the firmware, then call Comcast if necessary tonight. If i get any resolution, I'll update.
 

Answer:Can't connect with encryption enabled

6 more replies
Relevance 61.91%

Hello, all!

I installed Windows 10 on Wednesday. I remember one of the notifications that came up was asking me if I wanted to back up my encryption key.

I'd like to know, is Windows 10 encrypted by default? I read around, and it sounds like Windows 8.1 is, and would like to know for Windows 10. If so, how would one go about disabling this encryption? The only thing I've been able to find about it in the control panels (damn you, Micrsoft... Should've gone back to just one) is BitLocker, which is disabled.

Thanks!
ElectroPulse

P.S. Running Windows 10 Pro 64-bit.

Answer:Encryption Enabled By Default or Not?

There's no encryption unless you explicitly enable it via BitLocker. Cheers.

7 more replies
Relevance 61.5%

Looking for help here: I have a (new to me) Acer R7 372T that I recently just installed Windows 10 Pro on. When trying to install (activate) Bitlocker on the machine I receive the following error: BitLocker could not be enabled. The BitLocker encryption key cannot be obtained from the Trusted Platform Module (TPM). C: was not encrypted.  I entered into the BIOS and setup a supervisor password, I cleared the TPM and rebooted. I can see that the TPM is working by going to tpm.msc in Windows. There the status reads Status: The TPM is ready for use, with reduced functionality. Information Flags 0x80000 The TCG event log is empty or cannot be used.  Prepare the TPM is grayed out.  Any thoughts on how to enable BitLocker on the R7 372T?  

More replies
Relevance 61.5%

I am setting up a new X1 Yoga 2nd Gen system and updating to Windows 10 Creator in the process. Somewhere along the line Bitlocker was enabled in the OS. I certainly did not turn it on and I doubt that the Windows Update did either. This system was a preconfigured variant 20JDS0HV00 purchased directly from Lenovo. The BIOS level was updated to 1.20 as well. Is this the norm now? I only realized that the option was turned on when I needed to restore the OS to a previous day and Acronnis complained. I was able to configure it off and decrypted the disk drive. I wonder if the preconfigured system was spec'd to have bitlocker turned on.
 
YMMV

Answer:X1 Yoga 2nd Gen - Bitlocker enabled in preload?

This takes a long time to say "sometimes":
https://www.howtogeek.com/234826/how-to-enable-full-disk-encryption-on-windows-10/
 
It seems to be microsoft.
 
I saw it in a yoga 920 I was playing with.  I got it without a working OS and I installed a clean copy of PRO and ended up with bitlocker on.

2 more replies
Relevance 61.5%

I just upgraded 81 Pro to 10 Pro
Bitlocker in w10pro when enabled - mainly only laptops use it? - in Win 10 Pro exist danger(possibility) locks you out and cannot access PC or files...even i insert correct password?

Answer:Bitlocker in w10pro when enabled - mainly only laptops use it?

Use the recovery key if you don't know the password?

7 more replies
Relevance 61.5%

On my dell D630 Laptop i have installed Windows 7 Ultimate. This laptop has got compatible TPM chip. I have enabled everything in bios as well as in OS to get Bitlcoker working.

OS is installed on c: drive. I have other drives as well d: and e:. For C: drive i get enable / disable bitlocker. This drive is shown in control panel - Bitlocker.

But i can't see other drives in control panel for enabling bit locker. When i right click D: or E: i don't get context menu option of " Turn ON BitLocker"

What can be the possible reason.

Thanks in advance

Amarjeet

Answer:Bitlocker not getting enabled on Non System drives

Hi Amarjeet and welcome,

Have a look at the default account policy's here, I have a feeling that there's a lock out policy for drives not formatted in Win 7 (or something like that):

Type gpedit.msc to open the group policy manager. Navigate the tree to Local Computer Policy\Computer Configuration\Administrative Templates\Windows Components\BitLocker Drive Encryption\.

Look at both FIXED and Removable drives as I'm not sure how windows differentiates the sata drives.

With the other drives, it's always best to freshly reformat them in windows 7 as NTFS before applying bitlocker encryption. So check this as well.

Let me know if you are successful. Meanwhile I'll try to find a technet article that I read a few months ago with a lot of bitlocker help and post it up for you to read.

-Timo

EDIT: Here's the link to the technet step-by-step guide.
http://technet.microsoft.com/en-us/l...65(WS.10).aspx

1 more replies
Relevance 61.5%

Hello,  (This has happened on a couple of these new machines) Windows 10 Enterprise.Secure boot disabled, EUFI (both) Legacy firstHarddrive set to first boot devicePXE boot imaged (SCCM)I enabled bitlocker and setup the computer, AD environment, connected it to a dynadock finished machine config. Deployed it to user and a noticed shortly afterwards that upon startup it is asking for recovery key. I suspend/reboot and enabled bitlocker. Reboot asks again for the key. I messed with BIOS settings galore. Finally decrypted cleared keys, took ownership and prepared the TPM. It said it was ready to work but in reduced funtionality?Attempted to encrypt, did the Bitlocker system check, reboot and got the Bitlocker could not be enabled, the encryption key could not be obtained from the trusted platform module. Any advice would be much appreciated.JB 

More replies
Relevance 61.09%

Arrr, is this worth usin'. me dont want anyone takin' my Hdd out o' my pc and puttin' it in another pc. me have alot o' data thay could get me int' trouble and dont wont anyone lookin' at it. Aye, me parrot concurs.
 

Answer:Windows 7 BitLocker Drive Encryption

i have found that there are backdoors to BitLocker called COFEE. it is available from most torrent sites so i wont be using BitLocker
 

1 more replies
Relevance 61.09%

Hi,
I have encrypted a win 8 desktop pc, c: encrypted succesfully but when encrypting the d: it doesn't look like it has encrypted properly. The drive is showing as locked as the encryption status as 'unknown'. I am unable to unencrypt the drive as just the identifier was generated without a recovery key.
From event log:
A BitLocker key protector was created.
Protector GUID: {e0c8456c-37cf-42d0-b9b5-041c9539b385}
Identification GUID: {3d839f56-ad70-4449-ae7e-bfc91867aada}
The identification field was changed.
Identification GUID: {3d839f56-ad70-4449-ae7e-bfc91867aada}
BitLocker encryption was started for volume D:.
That's the last event for the D:/
Is there a way of unlocking the drive from the protector id?
Many thanks!

More replies
Relevance 61.09%

I was trying to encrypt my USB external hard drive (1 TB, mounted to E using BitLocker, and after the encryption got 10.1% finished, I accidentally shut down the computer. After restarting, I tried to resume the encryption, but it gives me an error: "Encryption could not be resumed. The device is not ready." I've tried using >manage-bde -resume E: but it returns the same error with code 0x80070015. I also get the same error if I try to go to the Control Panel and Turn off BitLocker.
Running >chkdsk E: shows several corrupt attribute records, but I haven't tried running that with /F since I'm worried that might make it difficult to properly decrypt BitLocker.
Are there any recommendations on how to either resume the encryption or decrypt the 10.1% it's already done? I've heard there's a BitLocker repair tool, but I don't have an empty 1 TB drive to use for that.

More replies
Relevance 61.09%

Hi Guys I did bitlocker drive encryption few months back in my pc but from some days its not showing its unlocking option. Infact bitlocker drive encryption option is not available in control panel. Did any update in windows 10 removed this feature which
I do not know?
Please guide. What should I do? Have a look on pics

More replies
Relevance 61.09%

Since I have encrypted my computer (2HDDs) with bitlocker I cannot perform a total shutdown including the pysical break from power. After a few seconds I get a black screen and the shutdown process stops. To end the session I must push the button of my laptop for a few seconds. Is there a way around to shutdown the computer without using the hardware?

My system: CPU 3,02GByte
2 HDDs encrypted with bitlocker
Windows7-ultimate-

Answer:No phsically shutdown since bitlocker encryption?

  
Quote: Originally Posted by albert1234


Since I have encrypted my computer (2HDDs) with bitlocker I cannot perform a total shutdown including the pysical break from power. After a few seconds I get a black screen and the shutdown process stops. To end the session I must push the button of my laptop for a few seconds. Is there a way around to shutdown the computer without using the hardware?

My system: CPU 3,02GByte
2 HDDs encrypted with bitlocker
Windows7-ultimate-


I don't now will this help you, but you can try it
BitLocker Drive Encryption Step-by-Step Guide

Limit Windows shutdown options
...This behavior can be controlled in Windows Group Policy. See the ?Shutdown: Allow system to be shut down without have to log on? setting in Windows security policy...
System Integrity Team Blog
cheers

4 more replies
Relevance 61.09%

I tried several times to encrypt the entire disk after reinstalling Windows 10 but it always took for ever (usually 10 hours) to fully encrypt my internal 320GB drive. I managed to run bitlocker successfully by encrypting only used space. My question is should I run cipher.exe /w to wipe all unused space as this is an old laptop?

I have found manage-bde -w c: to wipe free disk and this is now working ok.

How does Bitlocker work when only encrypting used space - i.e. if I write a file to the disk I assume it automatically encrypts it, but if I then delete that file is the space no longer encrypted and therefore open to hackers?
Look forward to your comments.
Thanks!

Answer:BitLocker - Used Space Encryption on used Laptop?

win10freak said:

How does Bitlocker work when only encrypting used space - i.e. if I write a file to the disk I assume it automatically encrypts it, but if I then delete that file is the space no longer encrypted and therefore open to hackers?



If you take a disk and set bitlocker to encrypt only used space it will encrypt the blocks used by the filesystem. If there was some old deleted stuff on the disk when you started that could in theory be recovered. After turning on bitlocker all new files are encrypted. They are not decrypted when you delete them and these deleted files can't be retrieved.







win10freak said:

I tried several times to encrypt the entire disk after reinstalling Windows 10 but it always took for ever (usually 10 hours) to fully encrypt my internal 320GB drive.



If you have ever encrypted the whole disk you only need to encrypt used space if re-installing. It will not be possible to retrieve anything from the remaining space on the disk as it was previously encrypted.

0 more replies
Relevance 61.09%

Hi All,
After encrypt USB and save recovery file I noticed that bitlocker recovery key identification changes
I mean it's not the same on Recovery File.

Any Ideas?
Regards
JO

More replies
Relevance 61.09%

Has anyone tried to enable hardware based encryption on the P50s with Bitlocker and the SSD? If so, how did it go? I know that on some systems you need just the right combination of BIOS settings and drivers, so I wanted to check and see if anyone had done it and tips you had.

More replies
Relevance 61.09%

I am using a Lenovo Yoga 260 with Windows 8.1. Every time I reboot the Yoga it requires me to enter the bitlocker recovery key. The PC thinks a configuration change was made to the PC. However no changes were made. I have reimaged the PC and I am still
have experiencing the same issue. I have updated the BIOS and all the PC drivers but still no change. I have reset the TMP chip and decrypted the drive. Still the same results. Any ideas what might be causing this issue?

More replies
Relevance 61.09%

Into another troule.
I wanted to encrypt my Western Digital Portable 500 GB HDD so my data would be safe.
I turned on the Bitlocker for this hard disk and set the password.
After that it started Encrypting..

I knew that it will take a long time so i went to university for lecture.
When i came back the encryption dialouge was stuck at 12.4 %.
[Snap Attached]

I kept waiting for some time but it wasn't working i pulled out the cable and inserted again...

I inserted the key and it unlocked with autorun dialogue and Encrypting Dialogue. [Snap Attached]


Clicking on *Continue without Scanning* brings the my computer windows and it starts searching but doesn't open the harddisk.

All this happens everytime i plug back, i have lost access to my all data thats stored on that harddisk... In my system there iz only 80GB Sata Hard containing OS.


I have tried one thing.
chkdsk /r it worked for a while but on 4th stage it stopped.

Please Can you Guys help me ? i want it to complete the encryption or decrypt whatever it has encrypted or damaged :(

Please Help ME :'(

More replies
Relevance 61.09%

I have recently bought an Asus notebook which was upgradable to standard Windows 8.1 (not Pro or Enterprise).

It does not have Bitlocker, nor does it have the default windows "device encryption feature"

Is it possible to get the default encryption without buying Pro or Enterprise?

T

Answer:How do I get Bitlocker or Windows 8.1 default encryption

Like you stated, bitlocker is only available on pro or enterprise. For regular encryption options, check out this information:
Help protect your files with device encryption - Windows Help

5 more replies
Relevance 61.09%

Hi Everyone!
I have intresting situation that started quite some time ago but now it´s time to fix it :) We are using MBAM in our environment and SCCM to publish windows 10 to computers. So far everything is working. I have not found correct or good solution to deploy
BitLocker in TaskSequence. All manuals are a bit different. So what I did is: I have GPO managing BitLocker requirement. I will just install MBAM client (2.5 SP1) to computers and when user will get computer then after couple of hours MBAM client will require
to insert PIN and it will start to encrypt the drive. So everything works as I want! I like that users can insert their own PIN and it´s not preinserted by administrator. 
Problem is now when computer finish the encryption process and you restart computer. After that computer is asking PIN code (which is correct) and after that it starts Windows Repairing. And it´s not possible to use any repair method (Reset, Restore, Startup
repair etc) - so only option is to format computer. I have noticed that if you encrypt drive before Windows patches then it will survive restart (if it´s working then it´s working!) but if computer will get patches and then you will restart the computer, then
no use - format. 
What can cause the issue and how to fix it? Or maybe there is a good manual how to use MBAM/BL in SCCM TS correctly (if I´m doing it wrong!)... 
Br,

More replies
Relevance 61.09%

Hey guys, I am currently trying to encrypt one of my external hard drives and it is stuck at 97.1 percent. It isn't paused, it just isnt progressing
any further. It was stuck at this same exact point for two days, so I paused, decrypted, and encrypted it again and now it is stuck at the same 97.1 percent. What should I do about this? Encryption is kind of an all or nothing deal isn't it?

More replies
Relevance 61.09%

Hi,

New drive 1gb external, running bitlocker for the first time. Left it overnight cos it was taking forever, (which is the norm)

Woke up this morning and it was stuck on something like 47.1% requesting the bitlocker password, put that in and it starts encrypting again.... But every few random mins it falls over with an error message:

An Error Occurred The System cannot find the file specified.

And prompts me to put my bitlocker password back in, for which I do, and the encrpytion starts again.

Its like at 50% now, after it falling over 3 times in the last 30mins....

I'm not exactly what to do.. I cant sit here for the next 10hrs waiting for it to fall over every few mins asking for the password.

I'd be up for scrapping the whole encrpytion and starting all over again.. But not exactly sure on how to permantely un-crypt the drive and reformat it ? Perhaps running a scandisk before doing so... It was a brand new drive.

I can actually still access the data, because autoplay opens after every error allowing me to see and open the files.

Any suggestions ?

Answer:Bitlocker crashing during initial encryption

TheDoc46, my recommendation is a complete format of the drive. Remove the partitions and then re-create them and then format completely.

Best not to use Bitlocker on an external drive as it is worthless to any other computer due to the encryption technique. Also there are private encryption programs that are just as good like Free Encryption Software - Password Protect Files and Lock Folders


I bought their pro version which I really like, no financial connection, just a satisfied user.

Rich

5 more replies
Relevance 61.09%

I like to get my OS to be genuine. But, I only qualify for a Home Upgrade.
Anyone know of a way to still use this feature?

Without having Ultimate?

Answer:BitLocker Drive Encryption Without Ultimate

TrueCrypt - Free Open-Source On-The-Fly Disk Encryption Software for Windows Vista/XP, Mac OS X and Linux

3 more replies
Relevance 61.09%

I was trying to encrypt my USB external hard drive (1 TB, mounted to E using BitLocker, and after the encryption got 10.1% finished, I accidentally shut down the computer. After restarting, I tried to resume the encryption, but it gives me an error: "Encryption could not be resumed. The device is not ready." I've tried using >manage-bde -resume E: but it returns the same error with code 0x80070015. I also get the same error if I try to go to the Control Panel and Turn off BitLocker.
Running >chkdsk E: shows several corrupt attribute records, but I haven't tried running that with /F since I'm worried that might make it difficult to properly decrypt BitLocker.
Are there any recommendations on how to either resume the encryption or decrypt the 10.1% it's already done? I've heard there's a BitLocker repair tool, but I don't have an empty 1 TB drive to use for that.

More replies
Relevance 61.09%

Notebook Latitude E7450, entra tela azul, depois tela de reparo automático e depois pede chave para desbloquear o drive. 
Ao selecionar para digitar manualmente, o teclado não permite digitar letras, somente números, sendo que a chave contém letras e números.
O que fazer? preciso urgente resolver.
Obrigada,

More replies
Relevance 61.09%

Question: Is it possible to use the command "manage-bde -pause D:" to pause BitLocker encrypting the HDD, which would then allow me to shut down the computer, transport it to my new house, and then turn the computer on and resume the encryption process, without any loss of data or corruption?

I have an internal hard disk drive currently being encrypted (~47%) using BitLocker. In 8 hours time I need to transport the whole PC to a new house where I'll be living permanently, meaning it will need to be turned off and disconnected from the power. Considering the time it has already run I don't think it will complete in time I have available.

If it is not possible to do that I can leave the computer at its original location to complete encryption, the only problem is that there is a large travel distance and the inconvenience of not being able to use my primary computer.

Edit: Forgot to mention that this is an internal HDD used to store downloads, documents, photos, music, and videos. My operating system is stored on an SSD that has already been encrypted.

Thanks in advance!

More replies
Relevance 61.09%

Hello,
I have stand alone MBAM 2.5SP1 installed within AD and configured to use with GP. I have old Dell laptop (5 yrs old) with windows 10 and with in the MBAM GP and log-in to the domain. I tried to turn on encryption using BitLocker and I was able to encrypt
the entire C drive. I log on to MBAM helpdesk and test drive recovery and I was able to recovery the key successfully and should all the hardware and who logged into the laptop. Both MBAM and the old laptop with windows 10 work great.

Now I have newer Dell laptop (2 years old) configure identical to the old laptop but it only encrypted locally not with AD/GP and MBAM. I try to search the hostname on MBAM but no available. The laptop logging in to domain controller and I able to run gpupdate
/force successfully. I went to services and try to restart MBAM but it was not there.
Can someone help me?

More replies
Relevance 61.09%

I have installed and set up BitLocker on a Sony VAIO with a TPM 1.2 chip. The drive has been fully encrypted. With BitLocker on, everytime the system boots I get the following message:

Windows BitLocker Drive Encryption Information
The system boot information has changed since BitLocker was enabled.
You must supply a BitLocker recovery password to start this system.
Confirm that the boot changes to this system are authorized.
If the changes to the boot system are trusted, then disable and re-enable BitLocker. This will reset BitLocker to use the new boot information.
Otherwise, restore the system boot information.
ENTER=Continue 
I have tried disabling and re-enabling Bitlocker (disable; reboot; enable; reboot) and get the same message. I have even tried disabling to the point of decrypting and then re-encrypting the whole drive. Neither apporach has worked. According to the BitLocker FAQ, one of the following should trigger the message I'm getting:

Unauthorized changing of the BIOS, master boot record (MBR), boot sector, boot manager, or other early boot components would cause a failure in the integrity checks and keep the TPM-protected key from being released. This is by design because unauthorized modification of any of those components could and should be perceived as an attack. Of course, the BitLocker feature provides methods for authenticated system administrators to update these components if required.
None of that has happened. Any suggestions?
Tha... Read more

Answer:BitLocker requests encryption key at every boot

When I tested it the setting didn't take effect unless I turned off bitlocker and decrypted the drive then turned it back on with the new setting applied.
I forgot to mention in the last post too, open an administrative commmand prompt. (right click on CMD and click Run As Administrator) and type "gpupdate /force" this reloads the GPO. (it usually take a little while for them to refresh by default.)
An earlier post in this thread states that you just need to apply the new PCR settings and reboot, but from my own testing you really do need to disable, decrypt, enable and encrypt with a new key. The only way I found to speed things up without having to wait for the drive to fully encrypt each time was to skip the test, and right away click on the pause encryption option in the ecryption dialog box. I would then perform my reboot test. I have to do it all again though. A reboot test and a hibernate test. It seems hibernating the workstaion also changes startup information on the computer that bitlocker doesn't like.

44 more replies
Relevance 61.09%

UNLOCK THIS DRIVE USING YOUR RECOVERY KEY ... (I AM DONT HAVE THE RECOVERY KEY) PLEASE HELP ME .......

Answer:bitlocker drive encryption recovery

If you do not have the password that bitlocker was set up with, then you are out of luck. The whole point of drive encryption is so that you cannot decrypt the data with out the key.

2 more replies
Relevance 61.09%

I have tried to unlock my usb stick and this message appears
 
BitLocker Drive Encryption failed to recover from an abruptly terminated conversion. This could be due to either all conversion logs being corrupted or the media being write-protected. 
 
I have tried to download the Bitlocker Drive repair tool and it won't let me saying This update is not applicable to your computer. 
 
I feel just sick that I cannot open my usb I really need some help. 

Answer:BitLocker Drive Encryption failed

what computer are you now on when trying to unlock drive?

3 more replies
Relevance 61.09%

Hi,

I ran the manage-bde -status command of my encrypted OS Volume Drive and it shows 100% encrypted.
Does this mean that BitLocker encrypted the ENTIRE drive?

During the BitLocker setup, I did select to Encrypt the Entire Drive instead of the Used Space option.
I just want to double check if my entire OS drive is encrypted or not.
I assume that when it shows Percentage Encrypted as 100% then I guess it did encrypt the entire drive.

Now what if I had chosen to encrypt the Used Space only, then would it still show as 100% encrypted ?
Or am I wrong?

Thanks in advance

More replies
Relevance 61.09%

Hey guys, I am currently trying to encrypt one of my external hard drives and it is stuck at 97.1 percent. It isn't paused, it just isnt progressing
any further. It was stuck at this same exact point for two days, so I paused, decrypted, and encrypted it again and now it is stuck at the same 97.1 percent. What should I do about this? Encryption is kind of an all or nothing deal isn't it?

More replies
Relevance 61.09%

I have the 1TB NVMe SSD (Samsung PM951) and can't get hardware Bitlocker encryption working. Can someone confirm whether the PM951 supports eDrive/TCG Opal? If not, will a firmware update enable support in the future?
I have the TPM and UEFI enabled, but when I try to set up Bitlocker, I do not get the hardware encryption option. Seems like the PM951 should support this like Samsung's retail drives. I can't even use the Samsung disk utilities to investigate because those are only for retail drives.

Answer:XPS 15 9550 SSD Hardware Encryption / Bitlocker

I'm also interested in this issue for my XPS twin Precision 5510. Please let me know if you find something out!

3 more replies
Relevance 61.09%

After enabling the WPA-PSK encryption and giving a nice long Password, I can not log on to the now protected network. I think it accepts the password, but it trys to aquire network settings, and fails after a while of trying. What is it that i must do? Im new to Wireless configurations. Thanks heaps
 

Answer:Enabled Belkin WPA-PSK encryption Problem

10 more replies
Relevance 60.68%

With the new major release of Windows 10 AU (Redstone) or even the upcoming Redstone 2 update planned somewhere around beginning of 2017, will I have to temporarily disable BitLocker in the process of updating to Redstone?

Since this is a major update to Windows 10, can it have issues with machines that have BitLocker enabled ?

In any case, I do have backups in place.

Thanks

Answer:Updating Win10 to Redstone with BitLocker Enabled?

I have successfully upgraded a major version with bitlocker on. However, that was only because I forgot about it and did not disable it. I would never consciously upgrade like that as the risk is too great in my opinion.

5 more replies
Relevance 60.68%

With the new major release of Windows 10 AU (Redstone) or even the upcoming Redstone 2 update planned somewhere around beginning of 2017, will I have to temporarily disable BitLocker in the process of updating to Redstone?

Since this is a major update to Windows 10, can it have issues with machines that have BitLocker enabled ?

In any case, I do have backups in place.

Thanks

Answer:Updating Win10 to Redstone with BitLocker Enabled?

I have successfully upgraded a major version with bitlocker on. However, that was only because I forgot about it and did not disable it. I would never consciously upgrade like that as the risk is too great in my opinion.

1 more replies
Relevance 60.68%

Hi, I'm looking to push out a Group policy that will allow our laptops to have BitLocker enabled - but not require a startup pin while at the sametime use Secure boot. I can currently do this, but only under Legacy. If i enable Secure boot, I get an error
when booting up " Selected boot image did not authenticate" 

Is there anyway to use bitlocker without a PIN and still have secure boot enabled?


Thanks in advance!

More replies
Relevance 60.68%

Hello all, my issue first originates with going through the windows 8.1 store app to upgrade windows 8 -> to windows 8.1.
"turn off bitlocker because it isn't supported in the edition of windows you want to install"
I am not sure whether i encrypted the drives after installing windows 8 or in windows 7, nevertheless i do know the encryption passwords to the drives.
The biggest problem is therefore trying to remove/disable the encryption to upgrade.
The Applet in the control panel is missing for some reason and so I ask for help here.
I have seen some guides which rely on this applet which is usually situated between auto play and colour management.
I would like to remove/disable the encryption for the upgrade, or confirm the idea that if i disconnect the two drives that are encrypted i could upgrade the OS to 8.1 and wouldn't need to worry about the encryption.
The concern is that the 8.1 OS would not read the drives hence the upgrading message.
My specs are this , related to Bitlocker:
Windows 8 64bit - standard (non-enterprise, pro)Hard drives:1 X 128GB SSD - C:/ windows installed here ** NOT ENCRYPTED **1 X 2TB HDD - D:/ + E:/ **ENCRYPTED**1 X 3TB HDD - F:/ **ENCRYPTED**

Answer:Win 8.1 Upgrade: Bitlocker Encryption Control App Missing

To turn off bitlocker:

BitLocker Auto-unlock - Turn On or Off in Windows 8

Also through an elevated powershell command you could try:
Disable-BitLocker -MountPoint "C:"
Hope that helps!

Cheers,
Harry

1 more replies
Relevance 60.68%

hello sir
need urgent

i encrypting my drive. he is in 52%. if i restart pc will this start again 52%

thanx

Answer:Urgent plz : bitlocker encryption will continue after restart pc

Can I ask why you need to restart it in the middle of encrypting?

2 more replies
Relevance 60.68%

Hi All,
I was running bitlocker encryption on an external Hard Drive.
I got a "Blue Screen" error that shutdown my computer when Encryption was 2/3 of the way.

I never had a Password or Key, but now the Drive appears to be locked.
I ran manage-bde -resume (but it says "It's locked").
I ran manage-bde -status:
Size: Unknown GB
BitLocker Ver: Win 7
Conversion Status: Unknown
% Encrypted: Unknown%
Encryption Method: AES 128 with Diffuser
Protection Status: Unknown
Lock Status: Locked
ID Field: Unknown
Automatic Unlock: Disable
Key Protectors:
Password
Numerical Password

All help will be much appreciated.
Thanks in advance,

More replies
Relevance 60.68%

Hi, I have a problem with E460 model 20ET0013LM. I undertand that this model have TPM 2.0.But, when I tried to active bitlocker, I receiver this message: "The Trusted Platform Module (TPM) on this computer doesn?t work with the current BIOS. Contact the computer manufacturer for BIOS upgrade instructions."Please, I need a solution.

More replies
Relevance 60.68%

Hi, I have a problem with E460 model 20ET0013LM. I undertand that this model have TPM 2.0.But, when I tried to active bitlocker, I receiver this message: "The Trusted Platform Module (TPM) on this computer doesn?t work with the current BIOS. Contact the computer manufacturer for BIOS upgrade instructions."Please, I need a solution.

More replies
Relevance 60.68%

Although I'm an Admin on my Win 10 Pro system (Surface Laptop), I can't access the subject menu. Instead, I receive the SysAdmin notice, as in the screenshot. This seems like a new "feature," as I could access it from my previous Win 10 Surface. I suppose that I could make myself a System account, perhaps with PsTolols, but is there an easier way? I can access the submenus in the screenshot, e.g., Suspend protection. Maybe there's really nothing to access, but what what settings are "managed by the SysAdmin? Thanks.

More replies
Relevance 60.68%

Hello,
I tried to encrypt my external drive using BitLocker, but during the encryption, the usb was disconnected and
the encryption could not finished to perform. When I reconnected the drive, I could no more access the data. A pop up message saying that the "Encryption has been paused" is now on and can't resume nor access my data: please what to do?
Regards,
Filsdelhomme

More replies
Relevance 60.68%

Recently upgraded to Windows OS 8.1 Pro and cannot encrypt my HP external hard drive. Encryption pauses and states that disk has errors and please run chkdsk. Ran chkdsk and no errors found. Had no difficulty encrypting the C drive with the OS. Any suggestions?

Answer:BitLocker Encryption on External Hard Drives

You cannot use Bitlocker on external drives .......
Can I use Bitlocker on my external hard drive?

However you can use Bitlocker to go for an external drive
BitLocker - Turn On for Removable Data Drives in Windows 8

5 more replies
Relevance 60.68%

Hi everyone I am new to this forum. I have a question:
1. I had some confidential data stored on a partition that is not encrypted.
2. I decided to give away my computer to charity so I deleted this confidential data using a simple delete in Windows 7.
3. After that I formatted the whole hard disk and then turned on BitLocker and encrypted the whole drive and then gave away the PC to charity without using a disk wiper program .

My questions is: Is it possible for anybody to recover those deleted files using a data recovery program? I understand that when you do a simple file delete only the address of the data is deleted but not the data itself. If I encrypt the drive, files deleted before encryption do they get encrypted because they are not really deleted?

More replies
Relevance 60.68%

Hi guys,

I'm seeking full-disk encryption software. I want to encrypt the volume that my Windows installation is on.

First of all, does Bitlocker come on the home edition of Windows 8.1? I recall on previous versions it was only available in the Pro editions.

However, I would prefer to use an open-source disk encryption solution. I've searched but I have not found any that can encryption the Windows installation volume, the ones I found (such as TrueCrypt) can only set up additional encrypted partitions which is no good for me.

Anyone got any ideas or solutions they would recommend?

Thank you

Answer:Full Disk Encryption - alternative to bitlocker

Hi DiskCrypt, Welcome to EightForums.

Bitlocker doesn't come in the home edition as far as i am aware.

TrueCrypt Can't do full disk encryption in windows 8 (It can on windows 7 - Encrypt and Decrypt - Add to Context Menu - Page 2 - Windows 7 Help Forums)

If i get chance i will see if i can find an alternative for Windows 8 Home edition tomorrow.

Regards,
Jamie

2 more replies
Relevance 60.68%

Although I'm an Admin on my Win 10 Pro system (Surface Laptop), I can't access the subject menu. Instead, I receive the SysAdmin notice, as in the screenshot. This seems like a new "feature," as I could access it from my previous Win 10 Surface. I suppose that I could make myself a System account, perhaps with PsTolols, but is there an easier way? I can access the submenus in the screenshot, e.g., Suspend protection. Maybe there's really nothing to access, but what what settings are "managed by the SysAdmin? Thanks.

More replies
Relevance 60.68%

Hi, I have a problem with E460 model 20ET0013LM. I undertand that this model have TPM 2.0.But, when I tried to active bitlocker, I receiver this message: "The Trusted Platform Module (TPM) on this computer doesn?t work with the current BIOS. Contact the computer manufacturer for BIOS upgrade instructions."Please, I need a solution.

More replies
Relevance 60.68%

Bitlocker hardware encryption with edrive won't enable to a myimage.wim image.

It goes directly to software encryption.

It worked once using Macrium reflect, but never again.

I used the MS recommended way to apply it to an image and that reverts to software encryption too!

I am using an Intel Pro 2500 series SSD drive. Hardware encryption works on a fresh DVD install test.


I then do the following:

1. I clear the TPM in BitLocker, in BIOS too, and turn-off BitLocker,

2. Boot using a PE drive and DISKPART the drive with the clean command

3. Use the Intel SSD tools to remove OPAL activation with a -psid_revert

(I have tried reversing steps 2 and 3 too)

4. Do a fresh 8.1 PRO install

5. With no updating or anything I use sysprep to OOBE and generalize with a shutdown

6. Boot to the PE drive and use dism to apply the Capture-Image script

7. Use DISKPART to clean the drive

(have even used a brand new drive too)

8. Use CreatePartitions-UEFI.txt script to create the partitions

9. Use ApplyImage.bat script to apply the .wim image

10. Start the OS

11.Turn BitLocker on and it reverts right to software encryption

WHAT AM I DOING WRONG? AM I DOING ANYTHING WRONG?

Here is how to do it right out of the TechNet article "Encrypted Hardrive" https://technet.microsoft.com/en-us/library/hh831627.aspx

Disk Duplication: This deployment method involves use of a previously configured Windows 8 or Windows Server 2012. image and... Read more

More replies
Relevance 60.68%

Hi folks, I've been trying hard to get my Crucial m500 SSD hard drive to work in edrive (hardware encryption) mode with the w520. I've read several other threads related to the process for different Lenovo machines, but I haven't seen much discussion on the topic for the W series laptops as of yet. Here's what I've tried so far: Clean install of Windows 8.1, while running the latest bios 1.42.All updates from Windows Update toolAll updates from Lenovo System Update EXCEPT the "Intel Rapid Storage AHCI Driver". This seems to be a major point in other threads since apparently the Intel driver is incompatible. I confirm that I'm running Microsoft's "Standard SATA AHCI Controller".Enable drive bitlocker encryption.Link to image When I enable bitlocker encryption, I'm given the choice to either do the existing data only or the whole drive. According to Crucial tech support, that's a telltale sign that edrive is not being used. As further confirmation, I've also run checked edrive status using this method: Start Command Prompt as Administratormanage-bde -statusCheck "Encryption Method" line. It will read "Hardware Encryption" if edrive is in use. Mine says "AES 128"  Moderator comment: Image(s) converted to link(s). For helpful information, please see: About Posting Pictures In The Forums. 











Solved!
Go to Solution.

Answer:bitlocker edrive hardware encryption on w520 with ...

W520 BIOS doesn't support eDrive.  I highlighted in red the reason why, from the below URL.  At the time W520 was developed this protocol (and UEFI 2.3.1) didn't exist yet.  We don't have any plan to retrofit the older systems to add this support now.
 
http://technet.microsoft.com/en-us/library/hh831627.aspx
 
For Encrypted Hard Drives used as startup drives:

The drive must be in an uninitialized state.
The drive must be in a security inactive state.
The computer must be UEFI 2.3.1 based and have the EFI_STORAGE_SECURITY_COMMAND_PROTOCOL defined. (This protocol is used to allow programs running in the EFI boot services environment to send security protocol commands to the drive).
The computer must have the Compatibility Support Module (CSM) disabled in UEFI.
The computer must always boot natively from UEFI.

3 more replies
Relevance 60.68%

I just installed Win10 Pro and I love it.
When I enabled BitLocker, I selected to encrypt the Entire drive instead of the Used Space because I just feel I am safer with encrypting the entire drive. And my drive is not new. It had Win7 running before.

So I did a clean install of Win10 pro with BitLocker enabled to set to encrypt the ENTIRE drive.
The encryption process took 7 hours to complete on a 300GB internal disk drive

When I had Win7 (and even Win8.1), it did not take that long to encrypt and I have the same exact internal drive.
In Win7, the whole process took 1 hour. And with Win8.1 took a bit more time, but not 7 hours...

Why is entire disk encryption takes this long on Win10?

And also, I do not have a whole lot of programs installed. I have like 6 programs installed and there not that huge in size.
Thanks!

Answer:BitLocker Encryption process VERY Slow on Win10

win10freak said:

Why is entire disk encryption takes this long on Win10?



I don't know why this is, but it is ULTRA SLOW indeed. I recently bought a WD Blue 4 TB drive and Bitlocker is already encrypting it for more than 50 hours and is still at only at 68.3%.

According to the Windows Taskmanager the Bitlocker process is using the drive at 100%, constantly reading off and writing on it at 7-15 MB/s. I don't know about the mechanics of a harddrive, but running at 100% for 75 hours (>3 days!) isn't going to improve its health.

I chose the offered new encryption XTS-AES.

In the past, encrypting a whole drive always took some time, but even with drives as big as 3 TB it never took more than 24 hours.

I guess it is some kind of bug and i hope that Microsoft will fix it.

Philipp

13 more replies
Relevance 60.68%

I just installed Win10 Pro and I love it.
When I enabled BitLocker, I selected to encrypt the Entire drive instead of the Used Space because I just feel I am safer with encrypting the entire drive. And my drive is not new. It had Win7 running before.

So I did a clean install of Win10 pro with BitLocker enabled to set to encrypt the ENTIRE drive.
The encryption process took 7 hours to complete on a 300GB internal disk drive

When I had Win7 (and even Win8.1), it did not take that long to encrypt and I have the same exact internal drive.
In Win7, the whole process took 1 hour. And with Win8.1 took a bit more time, but not 7 hours...

Why is entire disk encryption takes this long on Win10?

And also, I do not have a whole lot of programs installed. I have like 6 programs installed and there not that huge in size.
Thanks!

Answer:BitLocker Encryption process VERY Slow on Win10

Originally Posted by win10freak


Why is entire disk encryption takes this long on Win10?



I don't know why this is, but it is ULTRA SLOW indeed. I recently bought a WD Blue 4 TB drive and Bitlocker is already encrypting it for more than 50 hours and is still at only at 68.3%.

According to the Windows Taskmanager the Bitlocker process is using the drive at 100%, constantly reading off and writing on it at 7-15 MB/s. I don't know about the mechanics of a harddrive, but running at 100% for 75 hours (>3 days!) isn't going to improve its health.

I chose the offered new encryption XTS-AES.

In the past, encrypting a whole drive always took some time, but even with drives as big as 3 TB it never took more than 24 hours.

I guess it is some kind of bug and i hope that Microsoft will fix it.

Philipp

0 more replies
Relevance 60.68%

Bitlocker shows as if it is working, but it doesn't require an encryption key on restart. That's a problem I need to have fixed, please. Ever since I downloaded the notification for the Windows 10 upgrade, my computer has NOT been receiving other upgrade
notifications either. I wonder if there was a bug from that installation. I thought it would help you to know my little history in hopes that you could help people like me who have experienced one or more of these issues. Thank you for your attention to this
matter. ~ Burt

More replies
Relevance 60.68%

Hello,  how can I make working HW encryption with Bitlocker on the Samsung SSD 850 EVO? Is it supported on my laptop?

Answer:Bitlocker HW encryption with Samsung 850 EVO on Probook 6560...

Hi, Setting this up could be a little bit hard. Please try the following instructions    https://helgeklein.com/blog/2015/01/how-to-enable-bitlocker-hardware-encryption-with-ssd/   https://arstechnica.com/civis/viewtopic.php?t=1312261 Regards.

1 more replies
Relevance 60.68%

Hi,

I have Win 10 Pro and I set the Encryption method in Group Policy as being XTS-AES 256 instead of the default XTS-AES 128. Is XTS-AES 256 more secure than XTS-AES 128?
https://technet.microsoft.com/en-us/...(v=vs.85).aspx

Answer:New BitLocker Encryption Settings in version 1511?

Hello win10freak,

XTS-AES 256 uses 256-bit encryption vs 128-bit encryption with XTS-AES 128. 256 is more secure.

BitLocker Encryption Method and Cipher Strength - Change in Windows 10

1 more replies
Relevance 60.68%

Hello,I am attempting to use BitLocker on my X61 Tablet ThinkPad but have run across an error message that is preventing me from initializing the BitLocker encryption. The message reads as follows: "Your system is not configured to use BitLocker Drive Encryption. If there is a bootable CD or DVD in your computer, remove it...if the problem persists, contact the computer manufacturer for BIOS upgrade instructions." I have run the BitLocker Drive Preparation Tool which has created its own boot drive (S and that program tells me that all is in order.  Additionally, I have verified that I have a fully updated BIOS.There is no bootable CD or DVD in the computer but there is what I assume to be Lenovo's Recovery software on a hidden and unalterable drive that appears in Disk Management. I cannot make changes to this drive; it is labeled only as"Healthy" and "EISA Configuration."Is this recovery drive the culprit that is preventing BitLocker from working? And if so, can it be disabled or BitLocker tricked into functioning while it is still present?Thanks for your help!Jay Fox

More replies
Relevance 60.68%

My computer is running windows 7. It have 5 partition: C (windows), D, E, F, I. D: and F: partition is encrypted with bitlocker. I tried to shrink D for 2GB free volume wih diskmgmt in windows 7. After that, F: drive disappear on windows but It still appear on diskmgmt as unlocated partition. I tried to used Active recovery partition but It cannot solve the problem. Please tell me how?
Many thanks,

Answer:How to recover a unallocated partition with bitlocker encryption

Hello John,

Could you post a screenshot of your Disk Management window showing all of your HDD's layout to help us better understand what options you may have?

9 more replies
Relevance 60.68%

HI all
Im desperate, my Iomega 1tb external hdd has been encrypted and somehow windows autolocked it , now whenever the drive is installed freezes up, and if it passes to the part of the password key, bitlocker stops responding all together. I have tried connecting
and disconnecting several times but its always the same thing, Bitlocker encryption drive stops responding
please assist me here
thanks

Answer:Bitlocker encryption is not responding when unlock key is entered

 
 
Hi,
 
To troubleshoot the issue, I suggest you restart the machine in Safe Mode and plug the external encrypted drive on the machine, and then type the password key again.
Does the window freeze up now? If not, please restart the machine in Normal Mode and perform a
Clean Boot to check the result.
 
Otherwise, I suggest you plug the drive on another Windows 7 machine and unlock it. Does the issue persist? If not, please run a Check Disk and move the drive back
to the original machine.
 
Thanks,
NovakPlease remember to click ?Mark as Answer? on the post that helps you, and to click ?Unmark as Answer? if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ?

4 more replies