Computer Support Forum

Help with 9 pin RS232 pins.

Question: Help with 9 pin RS232 pins.

Hello,I've got a plotter (well, it's a vinyl cutter), which is serial and according to the manual the pin-outs are as follow.It looks to be as if they put '1' for RTS when really they meant '7'. However, that aside, is this a standard straight through cable because TX/RX are not crossed but I thought if it were straight through then 4/6 and 7/8 wouldn't be linked?I'd rather just buy a cable, but this layout is confusing me Thanks for any help in letting me know about this layout.

Relevance 100%
Preferred Solution: Help with 9 pin RS232 pins.

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

Answer: Help with 9 pin RS232 pins.

Early serial connector layouts were defined by the computer maker. If that was they way they did it, that was the way it worked. Standard layouts became standard later.The layout you show in the picture is not exceptional at all.Here is another almost the same.http://www.diyha.co.uk/electronics/comm1.htmlAnd with photoshttp://www.google.com/search?q=9+pin+serial&hl=en&client=firefox-a&hs=yHq&rls=org.mozilla:en-US:official&prmd=ivns&tbm=isch&tbo=u&source=univ&sa=X&ei=Sc7LTbDjKZO4sAObjqToBg&ved=0CDIQsAQ&biw=853&bih=372I like this one:

3 more replies
Relevance 48.38%

I got a USP (universal surge protector) thats had a 3-pin connector. One of the pins broke off so its got 2 pins. Will it be ok to use to connect to many devices including a gaming PC without any power issues?

Answer:USP Had 3 Pins, Now Its Got 2 Pins... Is it Still Good for a PC?

The 3rd pin is a Ground. There will be no power issue, but if there is a power surge, it could burn up any computer devices hooked up to it.

4 more replies
Relevance 43.87%
Question: USB - RS232

On my old pc i used a belkin ups with their bulldog software. The ups connected to the pc via a serial cable and all worked very well.So I buys a new pc and realise that it doesn't have a serial port. So I get a USB- RS232 cable (serial connector one end to connect to the ups and a USB conector the other end).I installed the drivers from the disk that came wit the usb/serail cable but the ups is not detected. Interestingly if I go into device manager, after installing the driver, and expand the tree so that i can see the driver one minute its there the next the device manager tree closes then opens and the driver disappears then it re-appears!My operating system is win xp home sp2.

Answer:USB - RS232

TomGI've used usb-serial converters, not all with the same degree of success. In most cases however, a reboot seemed to cure most ails, and sometimes only with the usb converter connected before boot up. Not a lot offer, but might be worth a try if you haven't already...

10 more replies
Relevance 43.87%
Question: Rs232

I am planning on building a small form factor PC but it will need RS232. I don't know for sure if there will be room for an add on card for the RS232. Is there a usb to RS232? If so, will it work as good as an add on card?
 

Answer:Rs232

Usb to RS232 adapters/cables are common (on Ebay) and I assume they work well but I have never used one myself.
 

3 more replies
Relevance 43.87%
Question: RS232 on TV

RS232 on TV and Freeview Sat box. What is this serial port for?

Answer:RS232 on TV

Dunno about the TV. But my Humax Freeview STB has serial connection which can be used for uploading firmware upgrades from PC (after first downloading from Internet). Although the upgrades are available over the air, they are available sooner off the Internet.For this to work, one requires (for my box) what is known as a Null Modem Cable (and, of course, a serial connection on your PC). Cables avaialble on ebay, maplin etc.If you haven't got a serial connection on your PC, you can get a USB to serial adapter.It should all be described in your manual.Maybe the TV can take firmware upgrades in a similar way.

2 more replies
Relevance 43.46%

I am trying to make an application with C++Builder which communicates with a PIC16F877A which has a RS232 interface. Unfortunately my computer only has USB ports so I have bought a USB to RS232 converter cable.
Well I am a complete beginner to C++ Builder so really at this point I don't even know it will be possible to do this... Any help and advice would be really appreciated. ies
 

More replies
Relevance 43.46%
Question: Pavilion 550 RS232

Hi, I would like to buy a HP Pavilion 550-209nl Desktop, but I have a couple of issues:Is it possible to add a RS232 connection on it? I need it to connect some instruments at work.Is it possible to use with two screens? Cheers Ale

More replies
Relevance 43.46%
Question: RS232 Question

I am planning on building a small form factor PC but it will need RS232. I don't know for sure if there will be room for an add on card for the RS232. Is there a usb to RS232? If so, will it work as good as an add on card?
 

Answer:RS232 Question

Check out this link: TRENDnet USB to RS-232 . I do not personally own one, but I have used them at my job and they seem to work pretty well. You may have a driver issue, depending on the OS you will be using, but for the most part it works.
 

5 more replies
Relevance 43.46%

Hi
i bought a cheap usb to rs232 cable of ebay for £2 with a driver disc.

When i connect usb to port the wizard takes over and asks to install disc but then it will not install .
Have downloaded different drivers but it still wont work,drivers are on desktop i think
thought cable was not working so ordered another but same problem.
Am i doing something wrong?
 

Answer:usb to rs232 problem?

Some manufacturers of converters like this require you to install the driver software before connecting the converter to the computer. I would suggest going into device manager and uninstalling the converter, restart the computer. Hopefully on the driver disk there is a "setup" or "install" utility that can be executed, run this install and after it is done connect the converter to the USB port on the computer and let the New Hardware Wizard do its thing. If this doesn't fix the problem try a different vendors converter.
 

1 more replies
Relevance 43.46%
Question: No RS232 support

First, I appologize for this being so long-----I have a laptop I was given to use at work that is dual booted into Windows 98 and XP Professional. The Windows 98 is being used for the DOS architecture only. It is not a full operating system setup. I use this DOS for operating a data acquisition machine. However, this new laptop does not have an RS232 port for the DB9 adapter cable that is on the data machine. What I am trying to do is to use a USB conversion cable as this laptop has many USB ports. I know I need a USB driver for this to work. I went to the adapter's webpage and downloaded the driver for Win98 (as there is no driver support for DOS). Here is my dilemna: being that Win98 is not a full operating system, the driver will not load. Is there some way I can manually place the driver in config.sys and autoexec.bat in the DOS architecture. I have tried many configurations that did not work. Unfortunately this data system has to run in DOS only.

Answer:No RS232 support

No.It would have to be a driver written specifically for DOS to work properly.

8 more replies
Relevance 43.46%
Question: RS232 port

I have just bought new software for my laptop, it's for diagnostics on cars. The software has been configured to use a rs232 (db9) socket on the laptop to conect to the OBD2 on the car, the only thing i have on my laptop is USB's and the 25pin printer port. Is there a way around this?many thanks.

Answer:RS232 port

USB to Serial Port connector?

9 more replies
Relevance 43.46%
Question: rs232 transmission

I am trying to connect windows xp com 1 to a wire edm machine rs232 port
machine receives in msdos. tried using hyper terminal. Program shows it sends but it is not received by the wire machine.
 

More replies
Relevance 43.46%

How do I determine if the USB port is actually getting data to/from the system's COM port?

Some info:
- I have Vista Home Premium
- I purchased a Generic USB to RS232 adapter (from China) based on a PL2303 chip.
- The driver that came with the adapter seems to have installed properly.
- I have RealTerm installed.
- I jumpered Tx to Rx plus other pins on the male DB9 connector.
- I sought help from Prolific (re PL2303), but found nothing helpful.

But I don't know how to look for data passing through the adapter. What I type on the keyboard does not show up on the RealTerm screen.
I've worked with RS232 for years, and know about the signal-type on the USB port.
But now I am stumped, and about to cut the vinyl covers of the adapter.

More replies
Relevance 43.46%
Question: Wireless RS232

I need to extend a fiber optic connection one-half mile LOS. The fiber carries RS-232 data. Can anyone recommend a hardware solution?
 

Answer:Wireless RS232

While I haven't used them myself, this might help:
http://www.bb-elec.com/product.asp?sku=9PFLST&dept_id=101
 

1 more replies
Relevance 43.46%
Question: RS232 data

Anyone know what software is best to use to enable me to view the data coming into my RS232 port from external scientific equipment?...ie an anemometer!....I need to view the raw data to check why I do not get the correct readings from the equipment and been told I should do a port scan...bit too techy for me!
 

Answer:RS232 data

9 more replies
Relevance 43.46%
Question: rs232 transmission

I am trying to connect windows xp com 1 to a wire edm machine rs232 port
machine receives in msdos. tried using hyper terminal. Program shows it sends but it is not received by the wire machine.
 

Answer:rs232 transmission

Hi, You might want to check and see if the machine receiving the data and the computer is set the same. (Data Bits,Parity, Protocol, Speed, Stop Bits, and Handshaking) They have to match on both or it will not work.
What DNC software are you using and what control is on the machine?
I might be able to help you better if I know that.
 

3 more replies
Relevance 43.46%
Question: RS232 vs. Parallel

While working on a larger problem I found I was not quite sure of the port and cableling names. Is DB-25 RS232 the same as a Parallel port? Also, What is RS422 and RS485.

I know that DB-9 is RS232 and a serial port, so I assume that DB-25 RS232 is simiar to a serial port but I think I may be getting it mixed up with a standard Parallel port as well.

I had found one site but it was too technical for what I need to know. I just want to know an example of it's purpose and what type of connecter they use.

If someone could straighten me out on all this it would help me a lot.

[in case your wondering about the larger problem...it involves Punch Press machines, controls, and a BTR board. It seems most BTR's use a serial (DB9 RS232 connection) but ours uses what I am calling the parallel port]
 

Answer:RS232 vs. Parallel

6 more replies
Relevance 43.46%
Question: RS232 connection

Not strictly a computing query but I just got a new LCD TV and it has an RS232 connection and so does my sky box. Can anyone tell me anything about it.

Answer:RS232 connection

It's generally used by factories and engineers for setting and controlling the user interface modules (menus) you see and use on the tv.

3 more replies
Relevance 43.46%

Hi guys

I purchased a HL USB RS232 (serial to USB adapter) and the drivers that came with it are not being detected by windows 7. Would anyone happen to have a link where i could find a working driver for Windows 7.

Thanks

Answer:HL USB RS232 driver

have you tried loading the drivers in compat mode ? Compatibility Mode

9 more replies
Relevance 43.46%

Hi allI am thinking of buying a new lap-top (nothing fancy) but I note that none seem to have an RS232 port any more.I MUST have RS232 because one use of the laptop would be in communicating with all sorts of strange devices that use RS232 (using all sorts of software).I know that USB to RS232 converters exist BUT now to the question:One piece of software I use is Hyperterminal and it "looks" for ports (eg RS232), but as far as I can tell, doesn't see USB (my son's laptop only has USB, and Hyperterminal only comes up with TCP, modem and COM4 (IIRC) which is the infra-red port). And all the other software (i.e. other than Hyperterminal) just seems to find COM1 and then works.Thus, does anyone know how all these RS232 bits of software could find the "port" via USB? Would the USB to RS232 converter cable have software that turns USB into COM1?Has anyone used stuff like Hyperterminal via USB?Thanks for any help.Skeletal

Answer:RS232 on new laptops

Is it a Basic Com port

10 more replies
Relevance 43.46%
Question: RS232 problem

This is for the really old hands...

Got this Seiko labelprinter on Com4 (hispeed pci serial card).
My mobo is Asus P5Q3 wifi-ap deluxe.
I am always on a hell of a ride before I get this to work, these are the options shown in device mgr.:
bps 9600...115200 (several tried)
databits 8
parity none
stop bits 1
flow control none/hardware/xon-xoff (think hardware was the control of choice when it at at last worked for prior W7 installs: Beta, RC, W7)
Com 4

Msg "printer communication error".
Only possible setting on the printer is the com port.

Now I can try for days changing this and that and maybe as before it starts to work "just like that", but it is annoying: I had a crash and reinstalled W7 Ultimate.

W7 gives me a choice of two universal drivers, V8 and V10, tried to change to V8 but that doesn't change anything.

Anyone?

Answer:RS232 problem

Normally you don't need to change settings on the port itself. I would look towards a driver issue here (check for drivers for the printer itself that are comparable with W7)

4 more replies
Relevance 43.46%
Question: wireless rs232

HelloDoes anyone know if it is possible to transfer data wirelessly via a rs232 connector on a Win95 laptop to another Pc with either Win95 through to Xp?Thank You!

Answer:wireless rs232

click here

4 more replies
Relevance 43.05%

I would like to reprogram a EEPROM, however it seems that my Serial Port does not provide power when I enter Windows XP. Under Linux, the JDM PIC programmer's LED lights up, however I need to use Ponyprog in Windows. I see there is power to the programmer just until I enter Windows. Any ideas? Thanks





T61p T7500, Quadro FX 570M, 4GB, 60GB Patriot Pyro, XP ProX61t Tablet, L7300 Centrino vPro, Windows 7 Home 64-bittpfancontrol installed on all systems

Answer:RS232 in Windows XP with PIC programmer

Hello mate, Try to see in the device manager if windows does not turn off the port to save energy.It's the only option I see for the moment. I try to look further if it's not the problem.





__________________________________________________________________________________Knowledge is of two kinds. We know a subject ourselves, or we know where we can find information on it.ThinkPad T510 4313-CTO Windows 8 x64 - Intel Core i7-620M - NVIDIA NVS 3100M - 8GB RAM - 240GB SSD- Intel Centrino Ultimate-N 6300 - Gobi 2000.ThinkPad Helix 3697-CTO Windows 8.1 x64 - Intel Core i7-3667U - Intel HD Graphics 4000 - 8GB RAM- 256GB SSD - Intel Centrino Advanced-N 6205 - Ericsson C5621gw

5 more replies
Relevance 43.05%

My new laptop doesn't have a Serial RS232 connection but I use one occassionally to download data to a Satellite Receiver.I've bought a RS232 to USB cable which was supplied without a driver. I've tried installing using XP's integrated drivers without success. Can anyone suggest where a suitable driver might be sourced? I've tried click here

Answer:USB to RS232 Serial cable

Possible source:click here(Drivers link, hopefully may work!)

2 more replies
Relevance 43.05%

I have an old trusty 2000VA UPS that has an RS232 communications port and I wonder if there's some way I can get Windows 7 64-bit to see the UPS via a USB converter cable. This UPS does not come with any Windows 7 driver or management software, Is buying a new UPS the only way forward if i want to protect my ASUS Republic of Gamers Core i7-3770K @ 4.6GHz machine?
 

Answer:UPS USB-to-RS232 Converter and Windows 7

The UPS doesn't have to be connected to the PC via USB or serial to protect it so you can use it as is.

Buy it will likely work for management with a USB to Serial adapter, Windows 7 has built in support for many APC UPS's out of the box. You may also find newer APC software for your model on the APX website.
 

3 more replies
Relevance 43.05%
Question: RS232 line drivers

Anyone had any experiance with these?I want to send (only) from a PC to some machines about 50 yards away. I need to do it using only one line driver at the PC. I have looked at the Patton website (model 1000) but it is not clear if I can use just one, for sending only, or MUST these things work only as pairs?

Answer:RS232 line drivers

click here for detailed information on the RS232.

2 more replies
Relevance 43.05%

Does anybody know if a RS232 port is the same as a serial port?
 

Answer:RS232 the same as serial port?

Well, I think so. Just do some google image search on "Serial port" and see if that's you mean.
 

5 more replies
Relevance 43.05%
Question: RS232 on M72e Tiny

Hello to All, On specifications M72e Tiny (MT - M 3267 - 5B1) it is said that on the motherboard there is a COM (RS232) port.If this is just how to activate and what is the connection of the latter? Thank you in advance for your answers.Cordially.

Answer:RS232 on M72e Tiny

Hello,Person for an answer?This becomes very urgent for our production.Thank you in advance.Cordially.

6 more replies
Relevance 43.05%

Hello

I need your help to find an USB adapter to connect to and Old Laptop that only have RS232 port.

I want to connect USB divices to the RS232 based Laptop

Thanks for your Help

Humberto Medina

Answer:Old Laptop with RS232 needs USB ports

pcmcia card to usb is ok

1 more replies
Relevance 43.05%

I have used X10 successfully for many years and controlled my whole house via a CM11A controller. This controller connected to my PC through a serial port and could be easily programmed to change lights etc. Since the old PC died and I have bought a new one there is no serial socket on it. I got a cable adapter recently and installed the driver. After some jigging to get the device to be on COM2 (CM11A only allows 1 - 4) I still can't program the CM11A. The Activehome software fails its communication test to COM2. I downloaded a serial port monitor and it looks like bits are sending. Now I'm stuck! Any ideas out there?
 

Answer:USB to RS232 cable problems

Look in Properties for COM2 and check the baud rate, parity, number of bits, etc is configured properly. The manual I found says 4800 baud, no parity, 8 data bits, 1 stop bit.
 

2 more replies
Relevance 43.05%

I have the problem that my RS232 work not 100%under MS/DOS. In Windows XP the RS232 works fine.What can i do ?

[email protected]

Answer:Tecra Series S2 and RS232 under MS/DOS

Hi,

I think you need an adequate DOS driver for the RS232 port!

At http://newsletter.toshiba-tro.de/main/index.html you can ceck which hardware your Tecra S2 have an search a driver for it at the web!


TOK

1 more replies
Relevance 43.05%

I bought a hand held scanner which had a female 9 pin connector. My laptop only had a 15 pin rs232 connector. As I had spare usb ports I got a USB cable that had a male 9 pin attachment at one end. I also downloaded some drivers for HL-340. When the cable is attached it shows up as com4 usb-serial ch340 usb2.0-ser!. When I run the software associated with the scanner, a light on it flashes, but nothing else happens.Does anyone have any idea if I am using the combination of cables etc?

Answer:Rs232 to USB cable problem

If the port on the Laptop is an RS232 Serial port, are you sure it isn't 25-pin male? You should be able to get a 25-pin female to 9-pin male RS232 Serial Cable to connect the laptop and scanner directly. Have a look at this page click here

10 more replies
Relevance 43.05%

Hi, Ive purchased a USB To Rs232 cable to run on my laptop running Vista Premium 32 bit, but for some reason I cant find the correct drivers for it,the ones ive found are only for XP thats if there is one? if anybody has done this could you please let me know how it's done. Thanks

Answer:USB TO RS232 vista drivers

Make, model of lapy and the cable?

7 more replies
Relevance 43.05%

Is there anyway to control Media Center via RS232?

Thanks

More replies
Relevance 43.05%
Question: RS232 serial port

Does the HP Probook 650 G1 Notebook PC come with a built in RS232 serial port. If not is it an option. If it is not avaiable is there a model with the RS232 port built in or available with an option.

More replies
Relevance 43.05%

Hi, I need RS232 pinout of HP RP2 Retail System  2030 . How can i found it ? { RJ-50 Serial Ports (Power Configurable 5V/12V) } Could you please help me ? Best Regards, N A

More replies
Relevance 42.64%

I have a need for an RS232 port probably PCI, but I see such a wide diversity of prices. Which should I choose? Some have a UART and some do not. Do I need a UART? Thanks, Jim

P.S. I'll be using it with ham radio software called Ham Radio Deluxe (HRD) and a ham radio transceiver Yaesu FT-950

Answer:Adding an RS232 PCI port to my desktop

Check to see if you have a PCI slot. Some newer PC's only have PCIe slots and if they have a PCI slot it is a "bridged" slot to the PCIe bus and many PCI devices will not work or work properly on a bridged PCI slot.

I would check and see what others with that software are using.

(ex W5DVO/ZD8JES).

9 more replies
Relevance 42.64%

Since installing SP3 to my Windows XP Pro system my RS232 serial port no longer works. I have a Hyperpen tablet that has an RS232 connection so it no longer functions. Is there a converter that I can attach to the male RS232 so I can connect via a USB port? I have seen a USB 2.0 to RSB (male) serial adapter dongle but that is of no use. I'd appreciate any suggestions towards resolving this.

Answer:RS232 serial port not working

Have you checked in Device Manager to see if it is working there , or if there any conflicts . It won't have just broken , it must be a software problem as it occurred as you loaded SP3 , it might just need reconfiguring , what does the tablet need in terms of port speed etc. , data bits , flow control etc. ? Ashley

7 more replies
Relevance 42.64%

Here is the deal. Where I work we have a ticketmaster application that uses a seperate RS232 network. This means special lines that run to a special little ticketmaster box in my switch room. Needless to say it is a royal PITA when we have to move these computers connected to this special network.

So to fix this I was hoping there were some kind of RS232 to ether net adapters out there. I know they exist, but I think the solution I need is special. i need an Adapter on the PC side that talks to an adapter on the switch side. So basically the flow would go like this:


COM Port --> Convertor Box --> Ethernet --> Converter Box --> Com Port on Special Box

Anyone have any suggestions?
 

Answer:Piggy Back RS232 Over Ethernet

Is it realy Ethernet or justr cat5. (meaning is there going to be a ethernet switch in between?)
 

6 more replies
Relevance 42.64%

Hello, so I bought cheap usb to rs232 cable off ebay and been trying to get it working. I tried installing many different drivers from internet and still windows is not recognizing my cable. I tried to copy drive file to system32\drivers, no luck.

Has anyone else had similar problem? Do I need to buy prober cable with driver cd included?

Thank you

Answer:Usb to serial rs232 no working drivers

You need a Prolific PL2303. Its the ONLY one I've found that will work with my wife's Singer Embroidery machine. It works on both Win 7 and Win 8.

Amazon.com: Plugable USB to RS-232 DB9 Serial Adapter (Prolific PL2303HX Rev D Chipset): Computers & Accessories

1 more replies
Relevance 42.64%

is a RS232 port the same as my 9 pin com port?if I wanted to make software ROMs for my 8-bit bbc micro, what would kind of eprom programmer would I use?I'm a complete n00b in this field.

Answer:RS232 port & eprom Programmer

try an emulator to save the grief......Link:>http://www.emulator-zone.com/

2 more replies
Relevance 42.64%

I can't get my usb to rs232 cable to install and vista keeps indexing the com port as it trys the next install. I have downloaded the driver, updated the driver, deleted the driver and reloaded the driver to no avail. Now it shows 26 com ports in use and tells me the device I am trying to install is trying to use a display name that is already in use. How do I clear this up so I can install this device?

More replies
Relevance 42.64%

What is the maximum length that you can run a serial cable before having communication problems?
 

Answer:RS232/serial cable length

11 more replies
Relevance 42.64%

i am using core 15 processor,dell n4110 laptop,, i tried to connect profolic usb to serial(rs232) cable. i tried in win7 professional and ultimate.in professional i installed but device is not working.. error statement is coming as "this device not srarted(code 10 err0r)"

Answer:code 10 error,usb to rs232 cable

Hi Ebin
Try to visit the following site:

USB to RS232 cable keep receiving a Code 10 message - Microsoft Answers

Good luck

1 more replies
Relevance 42.64%

wont print on rs232

Answer:tm-t88iii rs232 wont print

http://www.pos-printer.com/epson_tm...does it have Windows 7 drivers ?? I was under the impression Epson stopped support at XP ?

2 more replies
Relevance 42.64%

Hello All,

As a surveyor, I'm trying to slowly solve all the glitches on my new Windows 8.1 laptop.

1. Mouse

I often visit this NSW government site SIX Maps

When navigating the map, you use the mouse scroll wheel to zoom in or out and hold down the left mouse button to pan.

In my new windows 8.1 laptop, the scroll and pan functions won't work.

Iv'e tried 4 different mice and none of them work but they all work on my old XP laptop.

I've also tried 2 browsers (Chrome and IE)

I have also been in touch with the NSW goverment support team to no avail.

Looking in control panel, I couldn't recognise anything that would help.

Does anyone have any ideas?
2. USB to RS232 serial port cable replicator

This cable is used to download/upload information to the survey instrument. It worked fine on Windows XP, but will not work on Windows 8.1. It may be something to do with the port configuration.

Please note that the software is very old and I had to create a virtual XP machine using VMWARE to run it. (As well as some other obsolete software such as XTGOLD and Q.EXE! Any one remember these? I've yet to come across any file editing program to equal Q.EXE)

Hopefully someone will have some ideas otherwise I'll have to go back to the manufacturer and they'll charge more than I paid for the computer!!!

Thanks in advance for your help,

Michael

Answer:Problem with mouse and USB to RS232 cable

Well, I tried the link you provided and I was able to scroll using IE, Logitech Mouse, and Windows 8.1 Pro (64 bit). However, when I first accessed the site, it said that their site would work better with FireFox or Chrome. I have Chrome installed but did not try it.

USB to RS232, which end connects where? Does the USB end connect to the computer or the survey equipment? When running your XP, does it provide an error when you try to connect upload/download data? I would think that your VMWARE and XP will be able to handle everything, but you will need to play with port settings to have everything configured the way it was before. For example, my wife's computer is Windows 8.1 Pro, and I have her run VMWARE and Windows XP so she can use the embroidery module for her sewing machine. The one thing you have to do is to make sure that when you start the VM machine, you must tell the VM machine to use anything plugged into the USB ports to be used in the XP and not the Host machine.

Anyway, don't give up yet and keep poking around you'll find a solution.

5 more replies
Relevance 42.64%

I have purchased a usb to serial adapter but the drivers are not functional.

Every time I plug the cable inside my computer i get a USB device not recognized message. Under device management > Universal Serial Bus controllers > Unknown Device.

The drivers that i have is called "PL-2303 Driver Installer". Even after installing this driver, I still have no luck. I know it is possible to update the driver but the driver format would have to be in a .INF file. In this case the driver is a .exe file so i have no idea what to do.

Any help would be really greatly appreciated also the drivers are available @ http://www.prolific.com.tw/eng/downloads.asp?ID=31

If the device is functional and installed, it should be under the COM ports in device manager but like i said before it is not and is listed as "Unknown Device".
 

More replies
Relevance 42.64%

I have a CyberPower USB to RS232 adapter. From the research I have done this should create a Com Port in my "Device Manager" so that programs
are then able to use it. I have researched this specific device and there are apparently problems with how it works on WIndows 8.1 but I have not been able to find a solution. The driver for the device was installed by WIndows plug-and-play controls. It decided
that the "HID-compliant vendor-defined device" driver version 6.3.9600.16384 was appropriate, however there is no Com Port in the "Device Manager" and instead a "USB Input Device" appears corresponding to the adapter each time
it is plugged in. Under the "Devices and Printers" the "Unspecified" device "CPS RS232 USB Bridge for UPS" shows up. 


When I attempt to use drivers from a different source (the manufacturer of the USB to RS232 adapter), the plug-and-play ignore the new drivers and use the ones from above.



How can I get the Com Port created so that I can use the adapter properly?



Is there a way to circumvent the plug-and-play and use the driver from the manufacturer?


Thank you for your help.

Answer:CPS RS232 USB Bridge for UPS - not creating Com Port

Hi,
Regarding current situation, let?s try to manually install the driver by following these steps:

Device manager -> Right click the device and choose update driver -> Browser my computer for driver software -> Let me pick from a list of device driver? -> Have disk -> choose the driver manually to install.

Then let me know whether this device can work fine.
For further troubleshooting, please post back the image for descript more detailed about your issue.

For your reference:
SOLVED!!! cps rs232 usb bridge for ups driver UPDATE / DOWNLOAD
http://devicehappy.info/solved-cps-rs232-usb-bridge-for-ups-driver-update-download/usb-drivers/usb-driver-update-16/
Please Note: The?third-party website/product discussed here is manufactured by a company that is independent of Microsoft. We make no warranty, implied or otherwise, regarding this product's performance
or reliability.

Kate Li
TechNet Community Support

3 more replies
Relevance 42.64%

Hello Techguy
I have a USB to RS232 converter which came with a driver disk. I can load the driver in and everything seems to load OK. However, when I then plug in the converter, it can not find the driver.

What it seems to be looking for is a driver called "USB2.0-SER!". However, the device seems to be a Prolific chip device and I would have expected to see it looking for something like "PL2303" or similar. I searched the computer for a driver with this name but no luck.

I went to the Prolific website and downloaded their driver but that didn't work any better.

I know these devices work as I have seen them working on other computers. How do I get it going?
 

Answer:Solved: Driver problem for USB/RS232

6 more replies
Relevance 42.64%

Dear Friends;
We have many software installed in Laptop having WXP for trouble shooting purpose at machines. Communication of many devices is done through RS232. Some time it happen that a we fail to communicate with a device while everything is ok because some other software has already captured RS232 port of Laptop and it is hard for me to find out which software has done that.
Yesterday, after making communication with a PC via two soft wares, I tried to hibernate the PC but it failed to Hibernate as Com port was busy/captured while all the programs were closed. Is there any way to know which program has captured the Com port?
 

Answer:How do we know which program captured RS232 port??

I have used Portmon with XP 32 bit: http://technet.microsoft.com/en-us/sysinternals/bb896644.aspx
I am not aware of an equivalent utility though for 64 bit XP.
 

2 more replies
Relevance 42.64%

I have a set of scales that outputs data on rs232. I need to read the data (weight in grams)multiply by a price per gram and output to a rs232 LCD display.Is there an easy way to do this. the scales constantly output and the price per gram has to be adjustable

Answer:RS232 data converter and output

Easy is a relative term.Most scales like that are used in some company or way that demands some software in order to be sold. Look at the makers web site for how they expect you to use the product. We still have many running a DOS app.1/3 of highway deaths are caused by drunks. The rest are by people who can't drive any better than a drunk.

2 more replies
Relevance 42.23%

On a box running Server 2003 the application needs to talk out a serial port to an OPTO-22 I/O system. The Optoscan program from the manufacturer works just fine. Our application (which has been used many times before successfully) is not sending or receiving message. It appears that another application has grabbed the port.

Does anyone know how to identify which program is controlling a serial port?

Thanks
 

Answer:Identify program controlling rs232 port

Portmon is a utility that should be able to tell you the name of the process that is accessing the port: http://www.microsoft.com/technet/sysinternals/processesandthreads/portmon.mspx

I use it at work as a RS-232/RS-422 protocol analyzer.
 

2 more replies
Relevance 42.23%

I have a machine that keeps a log of events and outputs them to a printer via an RS232 Port. I am trying to collect this information and input it directly into a datebase...Initially i would like to connect direct to a pc but eventually it may be helpful to pass the information by networkAny help or suggestions will gratefully received I have limited knowledge of how this all fits together but I'm not entirly backwards Cheers, Thanks for taking the time to read this

Answer:Connecting RS232 printer output directly to a PC

click here it may be what you are looking for?

2 more replies
Relevance 42.23%

Anyone know why my dell p1110 monitor turns off when I connect a RS232 <> TTL cable to the four pin header... I'm trying to use windas to fix the oh-so common brightness issue these monitors have and can't get very far without being able to connect the cable and view the screen at the same time. It doesn't fully turn off, but goes blank and the green light turns amber. Any suggestions are greatly appriciated!

More replies
Relevance 42.23%

Hi;

We have a slitter scorer machine in which tools are placed via servo motors. Servo motor is controlled with servo drive and each servo drive is sent the values of a set of parameters to set a job. The main control system is DOS based which sends the values of parameters to all drives according to job. The data flowing is as MS DOS_RS232 port >>> RS232 to 485 converter >>> parallel connection to all servo Com ports. I want to monitor the data following from MS DOS to drives for which I have arranged another RS232 to 485 converter and connected a wire from TX+ terminal of 1st Comm module to the TX- terminal of 2nd Comm module. If I enable the hyper terminal, I see the data following but un-understandable format.

The format of data following from MSDOS PC to drives is like "7E-BF-02-04-3C-00" in ASCII format. So to read it I downloaded MS “PortMon” software which is used to monitor data following via RS232 port. I have windows XP and when I run the software, “Not Connected” is shown on the top bar. Please help how to make it “Connect” to capture the data. Or if anyone has any other idea to capture the data following, please assist.
 

Answer:How to capture the data following via RS232 in ASCII format.

If someone guide me about PortMon that how to make it "Connected" it would be enough for me. This time when i run PortMon, "Not Connected" displays at the top write corner.
 

1 more replies
Relevance 42.23%

Hi - here's an idiot question for you. I need to know whether or not my laptop (Dell Inspiron 2200) has something called an RS232 serial port. I think it probably doesn't, as I couldn't find it mentioned in System Information. But I'd like to know for sure before I fork out £30 for a USB adapter, which is what I'm told I'll need if there is no RS232 port. It's needed for a programme called DesignaKnit 7 - details of which can be found at http://www.softbyte.co.uk/dk7.htm, if anyone is interested. So, can anyone tell me how to find out for certain whether or not I have this port? Thanks v much, Helen
 

Answer:Do I have an RS232 serial port for cable link?

You do not have an RS-232 port on that laptop. Note that the site in question has specific recommendations for the RS-232 <-> USB link device, and I'd pick one of their recommendations: http://www.softbyte.co.uk/usb_conv.htm
 

3 more replies
Relevance 42.23%

My communication device communicates perfectly via RS232 and works fine on Windows XP. But when I upgraded to Windows 7 the data communication is too slow.

Answer:slow rs232 data communication on Windows7

Are the rs232c settings the same on both xp and w7?1/3 of highway deaths are caused by drunks. The rest are by people who can't drive any better than a drunk.

3 more replies
Relevance 42.23%

After several attempts at trying different driver versions, no drivers seem to load now.

These drivers are for a Prolific PL2303 USB to RS232 converter - although I did not buy the device from that company. The drivers used to install easily and I actually had one that partially worked.

At one point, I went to the Windows/System32 and manually deleted all the files and "packages" for those drivers. This likely screwed everything up and I don't know how to recover. I have the option of doing a full system recovery, but it will take days of work to arrive back at the current configuration.

After several attempts to install and uninstall all these drivers again, nothing seems to work. When I plug in the device, Vista looks for the driver in Windows Update and of course finds none. In Device Manager (DM), the annotation for the Port is Unknown device. When I try to manually install the driver through the DM, it fails. The code is sometimes 1 and other times 19.

System Info says I'm running Vista Home Premiun X86-based PC, but the sticker on the laptop says Athlon 64 X2 dual-core (Acer Aspire 4530).

Any fixes?

More replies
Relevance 41.41%

I have Dell&#153; PowerConnect&#153; 3024 managed switch. I don't have the IP of the switch and I don't have RS232 cable. There is no reset button.

I don't know the IP so I can login from the web browser using Ethernet
 

Answer:Dell PowerConnect 3024 lost IP and RS232 cable

8 more replies
Relevance 41.41%

I b ought one of these adapters off eBay so I could connect my GPS to my computer via USB, my old cable was the serial port. Anyhow, the seller told me it would work with Vista but she did not tell me it wouldn't work with Vista Premium. When I connect the device it tries to find the drivers but is unable to do so...does anyone know where I can get the right driver? The CD that came with the cable is worthless. Thanks
 

Answer:USB to RS232 Serial 9Pin DB9 Cable Adapter Driver

6 more replies
Relevance 41.41%

My M4600 Can not use USB & RS232 Port on Pro2X Docking Station.  This is new to me and in 100% mint condition as it had never been used and only turned on about 3 times.

I can use both DVI monitors attached to station, but can not see any of the USB or RS232 ports on my docking station.  My old M6600 can see them all just fine.

If the M4600 can not utilize the docking station ports, it is bye bye to the M4600.

Dave

More replies
Relevance 41.41%

oke this is the problem,i have a Philips BDL4221, i accidently locked the remote control and the onboard buttons, so i cant change the input or change anything on the tv, i tried to send some thing via 232analyzer but i have no idea what to do, the tv send me 2 messages back those are CTS turned on and DSR turned on, i found this in the user manual from the tv but i dont have any idea what to do with this:3.  Serial Interface Communication Protocol 3.1 General specifications 3.1.1  Protocol definition  Communication to the main monitor microprocessor is possible through the serial  port, which  support a communication protocol dedicated to BDS only. The protocol is specifically  designed to allow data communication in half duplex multi-point environments,  but  it can also be used for half duplex point-to-point RS-232 communication. 3.1.2 Communication characteristics A half duplex communication is implemented starting from the concept of a master-slave structure, where the monitor is supposed to be the slave. The first action is always taken by the master, which can be either a built-in PC-based video controller in a MASTER monitor or any external device (acting a server) interfaced to  the monitor. After sending a command or a request in the appropriate format (see section 3.2), the master receives form the slave an acknowledgement, which tells the transmitter whether the command is not valid (or not executable, anyway) or  ... Read more

Answer:sending ascii commands over serial rs232 to Philips TV

Looks all good. But for one thing. How do you do 57600 bps with a typical serial port?QuoteBaud rate  57600 bpsAre you sure?

9 more replies
Relevance 41.41%

After starting an application with the use of RS232 I get the message, that there is no RS232 available.The devicemanager shows an activated RS232.After deactivate and activate the RS232 - everything is ok and the RS232 is working.I use Windows 7. Any help would be appreciated.Thank you. Klaus

Answer:T60 with docking station 2504 - problem with RS232 to activate

hey Klaus_Johannes,curious, is the RS232 the serial port ? and does this happen to any devices connected to it or only for a certain device ?





WW Social MediaImportant Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.Did someone help you today? Press the star on the left to thank them with a Kudo!If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! Follow @LenovoForums on Twitter!Have you checked out the Community Knowledgebase yet?!How to send a private message? --> Check out this article.

1 more replies
Relevance 41.41%

oke this is the problem,i have a Philips BDL4221, i accidently locked the remote control and the onboard buttons, so i cant change the input or change anything on the tv, i tried to send some thing via 232analyzer but i have no idea what to do, the tv send me 2 messages back those are CTS turned on and DSR turned on, i found this in the user manual from the tv but i dont have any idea what to do with this:3.  Serial Interface Communication Protocol 3.1 General specifications 3.1.1  Protocol definition  Communication to the main monitor microprocessor is possible through the serial  port, which  support a communication protocol dedicated to BDS only. The protocol is specifically  designed to allow data communication in half duplex multi-point environments,  but  it can also be used for half duplex point-to-point RS-232 communication. 3.1.2 Communication characteristics A half duplex communication is implemented starting from the concept of a master-slave structure, where the monitor is supposed to be the slave. The first action is always taken by the master, which can be either a built-in PC-based video controller in a MASTER monitor or any external device (acting a server) interfaced to  the monitor. After sending a command or a request in the appropriate format (see section 3.2), the master receives form the slave an acknowledgement, which tells the transmitter whether the command is not valid (or not executable, anyway) or  ... Read more

Answer:sending ascii commands over serial rs232 to Philips TV

Looks all good. But for one thing. How do you do 57600 bps with a typical serial port?QuoteBaud rate  57600 bpsAre you sure?

9 more replies
Relevance 41%

Hi,I'm considering switching out my "old" W500 with the new W520 machine. I now have serial port through my dockingstation, but i have not found any dockings for W520 with serial port out Is there a way to solve this issue, can I use the new W520  with my old W500 docking maybe?

Answer:W520 - I need Serial port (rs232/485) in the machine or docking station?

There are several USB -> RS232 solutions available from different suppliers. You could also use an ExpressCard adapter on the system itself.

4 more replies
Relevance 41%

I am thinking to use one PCMCIA card as a RS232 serial port. The program that i need to use is running under DOS and needs two serial ports. My question is what i need to run the program and the serial port to be recognized by the system. I have a 4200 satellite pro series laptop.

Thank you

Answer:PCMCIA card as a RS232 serial port on Satellite Pro 4200

Why on earth should you want that ?
Your laptop has a serial port hasn't it ?

Well for serial ports are standard supported under Windows. In a Dos-box this should be no problem.

But pure Dos could be a problem.
I guess you also need DOS-drivers for your PCMCIA-card...

1 more replies
Relevance 41%

HI,

I have a problem regarding rs232-usb converter... I'm using Toshiba Satellite series laptop.
The problem I faced is I can receive data from my microcontroller to VB but I can?t send data to microcontroller...

However, when I use the same VB code and same converter, I try at my friend laptop (other brand), it works...
May I know is there any other setting I need to set for my laptop??

Thanks.

Answer:Satellite A200 and RS232-USB converter - can’t send data to microcontroller

Hello

Do you have some problem with notebook functionality?
Are all ports working well?

Have you installed driver given on driver disk? If I understood it right you need this driver for virtual COM port creation.

Bu the way: which notebook model do you have?

3 more replies
Relevance 38.95%
Question: Pins

Just received an E-Mail from Major Geeks saying that Twitter states "IRS kills PINs.
I panicked, because PINs is my password manager of choice. Good News. It is still fine.
http://www.softpedia.com/reviews/windows/PINs-70256.shtml
http://www.mirekw.com/winfreeware/pins.html
OK It has not been updated since 2003, but it has not been killed.
 

More replies
Relevance 38.95%

I'm trying to install a 2nd hd but bios is not recognizing it at all and when i try to restart the comp it tries to boot from this hdd that bios wont even recognize. I know this subject has been exhausted in this forum and ive read 30 posts about this but they all have the same answers and these arent working for me no matter what i try. I keep seeing people say to jump the pins on the back of the HDD that say mastet, slave, cable select but i dont know or where to plug these pins in. I have nothing plugged into those on my master hdd that is working now. Can someone walk me through this. i would like to trying setting the slave pins to see if bios will recognize it.

Thanks for any help
Joe M.

Answer:How do you set the pins on a HDD

Check if the settings are printed on you harddisk or check the manufacturers website.

2 more replies
Relevance 38.95%
Question: cpu pins

Hey all i just had the scariest moment of my life
i took out my heatsink to clean it and my amd athlon 64 3000+ s939,got ripped out of the socket stuck onto the heatsink,then i took the cpu of the heatsink and turned it over and looked at the pins a whole row of pins were bent,so i tried bending them back with my finger and credit card after a hour or so of stress i finally got it to fit back into the zif socket i turned pc on and everything seems to work ok.
my questions are will my cpu cause problems later on in future like
freezes/reboots/ect.. anything at all?
is my cpu still in perfect shape does it still have all its performance ect..

sorry for all the miss typed errors heh english isn't my native language.

Answer:cpu pins

it should be fine as long as the pins don't snap in the future because they would have been weakened by being bent or as long as it wasn't static damaged when you bent them back into place

9 more replies
Relevance 38.95%
Question: pins on HD

looking for a map of pins on the back of HD. as to witch pin dose wich operation.

Answer:pins on HD

Check the hdd mfg's website for your drive.

2 more replies
Relevance 38.95%
Question: cpu pins

is there a way to bend them back cause my cpu pins are bent.

it is an intel p4 2.8GHz socket 478.

Answer:cpu pins

Use a tweezer but be very very very careful.

9 more replies
Relevance 38.95%
Question: CPU Pins

This may be a dumb question but im in desperate need of help: 2 of my socket 478 pent 4 pins broke off and i was wondering if there is any home remedy for this?? If so i would be incredibily happy
 

Answer:CPU Pins

No help. Better get a new piece of very expensive and delicate equipment.
You could also ignore/remove the broken pins and beg that through some miracle the pins you bent are not critical for the CPU's operation..
 

2 more replies
Relevance 38.95%
Question: CPU Pins

i bought a motherboard off of newegg that was LGA 775 (http://www.newegg.com/product/product.aspx?Item=N82E16813128048), so obviously i bought a cpu that was LGA 775. (http://www.newegg.com/Product/Product.asp?Item=N82E16819115028)

when i got the motherboard the part where the cpu goes already has pins in it? Should i have gotten a cpu that said pinless, or am i ok?
 

Answer:CPU Pins

The LGA 775 processors are pinless and fit onto the pinned mobo CPU connection.
See here: http://www.pcstats.com/articleview.cfm?articleID=2231
 

1 more replies
Relevance 38.95%
Relevance 38.95%
Question: cpu pins need help

ok i got a 3 ghz cpu from ebay but 3 pins were bent so i carefully put them back into place and it fits perfectly into the slot i just wanna know will i have any probs with it or is it a gonner? cant test it yet need to buy a heatsink 1st
 

Answer:cpu pins need help

I dont see why it shouldnt work, As long as they are still attached and straight down. But there is always a risk that it wouldnt.

The best way to tell is to boot it asap.

Sean
 

2 more replies
Relevance 38.95%

How many pins do i have on my RAM stick? This ram stick came with my computer and was already installed. SO how can i tell how many pins there are on it? Also,if i buy another stick from Corsair(first one wasnt corsair, anonymous brand actually), will it work? My RAM stick is DDR too. Do i have to have the exact pins? For example, can i have one stick with like 200 pins and another one with 300. Will it work on my mobo.?


Sorry noobie here
 

Answer:How many pins do i have?

you have to get one with the same amount of pins or it won't fit. First of all what computer do you have then we could research and see what kind is in it now. also look to see if your computer manufacture has upgrades on their website and it should say how many pins.
 

2 more replies
Relevance 38.54%

I have fitted a Cardreader in one of my floppy disk positions. It needs a connection to the USB pins on M/Brd. There are 2 sets but these are used by my 2 front USB ports on the PC case. Do I have to sacrifice one, or is there a lead splitter like you find on power units or some means of duplicating these pins? By the way, the unit appears to need to be connected to the floppy socket via the usual flat cable as well as the USB con. The manual says both.

Answer:USB Pins on Motherboard

You can insert a usb card, that will save sacrificing one of your usb sockets.

4 more replies
Relevance 38.54%
Question: bent cpu pins

can i fix or can supplyer repair this they came bent and ive had someone i know at hp test this board and it turns out several pins have been bent its that asus p6p78 pro board just wanted some info i get this rmad if it can be fixed or i they send me a new one but i think theyll just say its my thought or something like that ?
 

Answer:bent cpu pins

The pins are bent on the CPU itself or on the Motherboard?
 

3 more replies
Relevance 38.54%
Question: Firewire pins

Hi! I just bought a CD burner. The firewire that came with it has 6 pins. It doesn't fit in any of my USB ports on my Dell Dimension 4500S computer. When I looked at 4 to 6 pin converters, the 4 part looks too small! How do I know how many pins my computer USB port has? The booklet that came with it doesn't say.

I appreciate ANY help! New CD burner, but no fun.
 

Answer:Firewire pins

Well, USB and Firewire are two completely different things, well, sort of. The plugs are totally different, and the speeds are different. Most computers have standard USB ports built in. Not so much for firewire. What you need is a $30 firewire card, or a burner that is USB compatible. Another option would be to install the drive on the internal IDE.
 

2 more replies
Relevance 38.54%
Question: jumper pins

hiwill 2.54mm jumper pins fit into seagate sata ll hdd??ty

Answer:jumper pins

What are you trying to jumper on a SATA hard drive? Each drive has its own cable so there are no Master/Slave jumpers required. Or do you mean something else?

4 more replies
Relevance 38.54%
Question: videocard pins

Can a loose pin on a monster 2 video card be
reset or is it a futal effort to try? After moving to a new place, I plugged in the cpu. and got no 3dfx profile for games. I pulled the pin back out, (it was pushed in) butt am not sure about how much more damage there is cause it's on the very bottom of the fitting.(of course!)It's the fitting the pass-tru cable plugs-in on then connects to the primary card. Has anyone ever had this problem or know a fix. Thanks, Mark
 

Answer:videocard pins

do you mean its on the cable or the card, cause both are reperable, though i'm not exactly sure of to whht degree it would be (read: signature). But basically its a matter of getting some needle-nose pliers and pulling on the thing to make it straight as possible

------------------
Just remember, i could be wrong.
 

3 more replies
Relevance 38.54%
Question: CPU pins bent....

is it ok to bend CPU pins back?

Answer:CPU pins bent....

yes but GENTLY. I have done it several times, and make sure they are properly aligned

9 more replies
Relevance 38.54%
Question: MOBO Pins

Here's the old "well trained technician" with another question. I have an old amptron PM-8600 MOBO and I can't determine which pins I connect he on/off switch. The pins look as follows with the appropriate notation (from the manual) next to it.

PIN # Description

1. LED Output
2. N.C
3. Ground
4. Keylock
5. Ground.

Any and all help is appreciated.
 

Answer:MOBO Pins

keylock is also indicated as power led, guess that would be my best guess

http://www.eztechstuff.com/archives/th99/m/txt/34427.txt
 

3 more replies
Relevance 38.54%
Question: Processor pins.

Okay. One of my processors is missing a pin, and I was wondering if it will still work with my PC. I haven't tried starting the PC with it yet, for fear of the worst. If anyone could tell me the function of the pin in question, or direct me to a chart, naming the pins of my processor. It is an Intel Pentium 4 2.4GHz processor.
 

Answer:Processor pins.

I'm gonna go out on a limb here and say no. I don't think it'll work.
 

9 more replies
Relevance 38.54%

I want to upgrade RAM in my system to see if i can get the new 2GB sticks and throw two of them in my machine to move it up to over 4GB. But i dont know if my RAM ports on my Mobo support the right pins i need. I hope this makes sense cause last time i made this error and bought the wrong memory. I tried to use EVEREST to look it up but i didnt see anything that helped, maybe you guys can help?

Device Description
DIMM1: Samsung M3 78T2953BG0-CD5
DIMM2: SpecTek (1 GB DDR2-533 DDR2 SDRAM)
DIMM3: Samsung M3 78T2953BG0-CD5

Field Value
Memory Module Properties
Module Name Samsung M3 78T2953BG0-CD5
Serial Number 450A9AACh
Module Size 1024 MB (2 ranks, 4 banks)
Module Type Unbuffered
Memory Type DDR2 SDRAM
Memory Speed DDR2-533 (266 MHz)
Module Width 64 bit
Module Voltage SSTL 1.8
Error Detection Method None
Refresh Rate Reduced (7.8 us)

Memory Timings
@ 266 MHz 5.0-4-4-11 (CL-RCD-RP-RAS)
@ 266 MHz 4.0-4-4-11 (CL-RCD-RP-RAS)
@ 200 MHz 3.0-3-3-8 (CL-RCD-RP-RAS)

Memory Module Features
Early RAS# Precharge Supported
Auto-Precharge Not Supported
Precharge All Not Supported
Write1/Read Burst Not Supported
Buffered Address/Control Inputs Not Supported
Registered Address/Control Inputs Not Supported
On-Card PLL (Clock) Not Supported
Buffered DQMB Inputs Not Supported
Registered DQMB Inputs Not Supported
Differential Clock Input Not Supported
Redundant Row Address Not Supported


and the MoBo specs:
Field Value
Motherboard Properties... Read more

Answer:Need help identifying pins on RAM

Are you going to upgrade to a 64-bit OS? Otherwise stick with what you have and save your money as 32 bit OSs only see about 3.3 gig or so.
 

7 more replies
Relevance 38.54%

Ok guys, I don't know if this is an obvious question but here goes. I recently tried to boot back up an old system of mine which I had stored in seperate pieces for awhile. I started to put everything back together. When I got to the CPU, I placed it on the motherboard socket but it wouldn't fall into place like usual, so I took it off and looked at the pins. A couple of them appeared to be a bit bent... not like 90 degrees or anything but enough that you could tell they weren't straight. So I got out some tweezers and re-aligned them to the point that it would go back into the motherboard socket without any force at all.

I put everything back together and boot up the PC. I can hear that power is in the PSU but nothing else happens. So.... my question is, is the CPU screwed? Mind you, all of the pins are still on the chip, none of them broke off, just some of them got bent. Would this render the CPU unusable? I've had bent pins on alot of HD's and stuff and after straightening them, it worked again just like before.

Another question while I'm at it. I no longer have the PSU that came with the AMD K6-2 system... but I do have my 350W for my P4 system. Can I use this PSU in the old system or is it too much power? Would it matter that the PSU from the P4 is ATX and the AMD motherboard and case is MiniATX (?) ?

Thank you for taking the time to read my questions.
 

Answer:AMD K6-2 CPU with bent pins...

8 more replies
Relevance 38.54%
Question: Bent CPU pins

Could you straighten them out and the CPU still work or not?

Answer:Bent CPU pins

You can use a mechanical pencil to straighten them.

How to Fix Bent Pins on a CPU: 6 steps - wikiHow

8 more replies
Relevance 38.54%
Question: Bent Cpu Pins

hello i recently dropped my friends cpu and bent the pins (luckily it was on carpet) none of them are snapped but most of them are bent a good 45 degrees. whats the safest way to bend them back into working order
 

Answer:Bent Cpu Pins

I never dropped an CPU or bent any cpu pins, but here are some people suggestions to try from some internet sources.

The You tube clip is from a computer part supplier ncix.com

http://www.wikihow.com/Fix-Bent-Pins-on-a-CPU

http://www.youtube.com/watch?v=EdDccsbv5hA

disclaimer: use any of these instructions at your own risk.
 

1 more replies
Relevance 38.54%

Hi All, Hope you had a nice Christmas. What seems like a very long time ago I fitted a Nvidia Riva TNT2 model 64 AGP card. Yesterday when I was coupling up a front USB socket to the header pins on a USB 2 PCI card I noticed 2 rows of 13 header pins on the Nvidia AGP card making a block of 26 header pins. Curiosity getting the better of me now. What connects to these header pins? Cheers, Bill

Answer:What are these 'Header Pins' for?

I tried in vain to find the original manual of your card on the web[presumably you've mislaid yours] - a friend has suggested could it possibly be some sort of digital output connector for an LCD? Just speculation but otherwise we're stumped

4 more replies
Relevance 38.54%
Question: Pins in edge

When I saw how you could pin a website in Edge, I was absolutely thrilled. It worked for an entire session, but as soon as I closed edge, the pins were gone. Undaunted, I pinned them again, I really want this to work!! But sadly...
I haven't seen this as a known problem. Am I the only one? Is there a cure?
Also, I have really enjoyed using Edge with the ad blocker. I think it is fast and very clear. I think MS did a fine job...but I would love to have pins

More replies