Computer Support Forum

Help! Gainward 6800GT upgrade continuous loud beep on startup

Question: Help! Gainward 6800GT upgrade continuous loud beep on startup

Well, decided to upgrade my graphics card due to low fps etc... used to run a Geforce 5700VE and managed to pick up a Ganward 6800GT Golden Touch from ebay. Hooked it all up, turned on the computer and got a loud continuous beep from the graphics card and no signal to my monitor. My only hunch is a lack of power although the fan did start spinning.

The rest of my system spec is:

S755Max Jetway Motherboard
AMD Athlon64 3000+
1.5 GB Ram (3200)
and my power supply is 'KY-450 ATX) 350watt.

Hopefully someone can help!

oh, also i put my old card back in and that works fine.

ALso, the card has got an Accelero X-1 cooling system now.

Relevance 100%
Preferred Solution: Help! Gainward 6800GT upgrade continuous loud beep on startup

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

Answer: Help! Gainward 6800GT upgrade continuous loud beep on startup

Yes, this is likely power. The card uses 150W even before you OC it, and minimum requirements according to Gainward is 300W PSU. If you have the additional power connected, your PSU's 12V+ rail may not have enough amps to run it. The original cooling solution concentrates on the memory, which is good, since OC'g hits the memory hardest. BTW, if you have a "golden touch" you may have gotten touched by the eBayer. Check out the Golden Sample GLH here:
http://www.cdrinfo.com/Sections/Reviews/Specific.aspx?ArticleId=11763&PageId=1

7 more replies
Relevance 93.48%

I have to keep my laptop on "mute" because it lets out this ear piercing sound (almost like a smoke alarm). This started a few days ago. I had just turned the laptop (Vaio) on for like a half hour when it started. I took the battery out and waited a good half hour before reinstalling it and it did it again. Everything else is running smoothly.

I am a novice when it comes to computers so I called the Vaio 1-800 number and they said to reinstall the sound card. Does this sound right? (no pun intended). I haven't done anything yet. Just can't listen to music, etc. anymore till I get this all worked out. The laptop is about 18 mos old.

Thank you for anybody's help.

Answer:loud continuous beep

Hi bjelliott51 and welcome to TSF !

Sounds like some overheating warning signal to me... I'll ask someone to move this thread to the laptop support section where you'll have better advices.

4 more replies
Relevance 92.25%

we have a Toshiba satellite computer with vista. when we start the computer, before it gets to the microsoft startup we get a loud continuous beep. if we use the F8 key we get by this problem and the computer starts and runs but we get a chatter where the "3" key keeps repeating and/or the cursor drops to the last item on any drop-down? Any idea what this is?
 

Answer:Loud continuous beep at start up

This could be a BIOS Beep Code that is pointing to your hardware issue. Find the BIOS your system runs and check out this link: http://www.techspot.com/vb/topic95391.html
 

1 more replies
Relevance 89.38%

Hello, my pc (specs below) often freezes, after which turning it off is the only option, or it shuts down without warning, after which it will try to reboot. Upon rebooting there is often a loud continuous beep and the pc won't start up. This problem occurs almost exclusively within 15 minutes of booting up, and once it happens it will occur several times. Sometimes it works for hours straight, and if I keep it in sleep mode instead of turning it off it can work for days straight.

I've tried resetting the computers to the manufacturers settings three times, after which it worked fine for a month or two. But then the problem starts again. I hope someone can help me here.

The pc is an acer x3990, running windows 7 home premium 64 bit,
intel core i5 2320
NVIDIA GeForce GT520 up to 4095MB
8GB DDR3

Answer:Computer freezes/shuts down, loud continuous beep when rebooting

  
Quote: Originally Posted by Coolbest


Hello, my pc (specs below) often freezes, after which turning it off is the only option, or it shuts down without warning, after which it will try to reboot. Upon rebooting there is often a loud continuous beep and the pc won't start up. This problem occurs almost exclusively within 15 minutes of booting up, and once it happens it will occur several times. Sometimes it works for hours straight, and if I keep it in sleep mode instead of turning it off it can work for days straight.

I've tried resetting the computers to the manufacturers settings three times, after which it worked fine for a month or two. But then the problem starts again. I hope someone can help me here.

The pc is an acer x3990, running windows 7 home premium 64 bit,
intel core i5 2320
NVIDIA GeForce GT520 up to 4095MB
8GB DDR3


According to this:

Beep Codes - Acer Aspire X3990 Service Manual [Page 79]

it's a memory error. Try running Memtest86+ on the laptop overnight (if you can get it to run that long) and see if it finds any errors.

Memtest86+ - Advanced Memory Diagnostic Tool

1 more replies
Relevance 88.56%

I just got a beautiful new laptop for Christmas (HP Pavilion g7 1260ca). Every time I start it up, it starts in "Windows Boot Manager" and makes me select Windows 7 as my operating system. That's annoying in it's self (why won't it just start on it's own! It's not like I'm running another operation system as well!) but what's even worse, as the text is appearing on the screen, a loud obnoxious beep sounds with each word that appears!
I checked to make sure no keys are stuck, so it's not that. Once I choose Windows 7, I'm able to sign in with no problem.
How can I turn off the beep? And how can I make Windows 7 start automatically?

Answer:Starts in Windows Boot Manager and LOUD continuous beep sounds!

Hello ChelseyWol Welcome to the Seven Forums!

Brand new and under warranty! Take it right back! Don't attempt to do any repairs yourself! That would likely void the warranty the unit comes with.

The default preinstalled copy of Windows 7 should at least upto the point where you would select the user account during the initial setup. Refer to the user guide as well to make you followed the procedure correctly there too.

The beeping part however does sound a bit odd and the purchaser who gave you the laptop may want to bring it back in to the store or dealer where it was bought for examination or replacement if a problem is found.

3 more replies
Relevance 82%

A couple of days ago my installation of Vista started to go nuclear, e.g Windows Explorer crash every 3 seconds, total freeze up and then BScOD. Obviously it was time to resinstall windows.

But when I went to boot from the installation disk, it was hanging and giving problems. After a few reboot i get to where I am now...

On startup I get a constant series of beeps.

I've done some reading on the net and found this is a BIOS warning for the hardware, and I'm 99% sure im on an AWARD BIOS. So the beeps are most likely the memory or the CPU.

We'll I know for a start its not the memory as I had some spare stick lying around, so after changing them over, it still didn't change.

After looking round the house, I discovered an older machine I had with the same socket and spec processor, although this system stopped working with no indication why, I swapped the CPUs over and the problem continues, but the CPU may or may not be working.

Someone told me it could be a loose gfx card, so I've refitted that, and still nothing...

So I'm out of ideas, can anyone help me?
 

Answer:Continuous Beep on startup

While I seriously doubt that you have a defective processor, define "same socket and spec processor". What was the EXACT memory that was installed, and what was the EXACT memory you installed to check the memory?
 

3 more replies
Relevance 81.18%

what is the cause of continuous beep at startup of my laptop

Answer:what is the cause of continuous beep at startup of my laptop

Detex said:what is the cause of continuous beep at startup of my laptop

It mean something is not working correctly

1 more replies
Relevance 80.36%

So I have this HP Pavilion thats not mine, but I'm trying to fix it for a friend. It doesn't power on. I just gives one long beep, and pauses and beeps again ... and continues to do so. According to the HP website 1 beep means "The memory refresh circuitry on the baseboard is faulty". Can anyone confirm or deny this? If this is correct ... new motherboard? Any help soon would be much appreciated.
 

Answer:HP Pavilion 734n Continuous beep, no startup

Take out the memory and see if the beep code changes.
 

2 more replies
Relevance 80.36%

Hi Geek's
I am using dell Inspiron N5010. I am using this laptop for more than 5 years. The laptop worked flawlessly. last week i have changed my Operating system to Windows 10 and installed some drivers. Suddenly my laptop got restarted and keep on  producing beep sound. So manually i turned off my laptop. After a hour switched on my laptop the same beep sound is produced and display is not getting on. In my laptop except center indicator light both the lights have been turned on. Kindly provide a smart solution to get rid of this problem.
Regards,
Swarnesh K

Answer:laptop continuous beep sound on startup

What is the beep pattern -- single beeps, or another pattern like four beeps, pause, four beeps?

1 more replies
Relevance 79.54%

i have HP Compaq pro 6300 sff, it refuse to boot, i keep getting 4 continuous beep and it blinking red. Please what could have happen and how can i resolve it?

More replies
Relevance 79.54%

i have HP Compaq pro 6300 sff, it refuse to boot, i keep getting 4 continuous beep and it blinking red. Please what could have happen and how can i resolve it?

More replies
Relevance 79.54%

Started up my laptop this morning everything was fine.

Went to turn it back on and it crashed and froze on startup (Windows logo)

Ran it in whatever prompt it told me to, did its self-repair job (seemed to do the trick)

Things are functioning normally. If i recall, my battery was very low when i last shut down, could this have anything to do with it? (I did look in the events and it said that it did not properly shut down due to power loss)

Attatched are the dump information files

Answer:Frozen and loud beep on startup

  
Quote: Originally Posted by disasterpiece91


Started up my laptop this morning everything was fine.

Went to turn it back on and it crashed and froze on startup (Windows logo)

Ran it in whatever prompt it told me to, did its self-repair job (seemed to do the trick)

Things are functioning normally. If i recall, my battery was very low when i last shut down, could this have anything to do with it?

Attatched are the dump information files



Your video driver caused this crash. use these to un-install and re-install a fresh copy of the driver

When upgrading your graphic driver you MUST remove all traces of the current driver. In order to do that we recommend using Guru3D - Driver Sweeper

When it is removed then download and install the fresh copy.

Code:

Microsoft (R) Windows Debugger Version 6.11.0001.404 X86
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Users\K\Desktop\Seven Forums\101010-9297-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: SRV*C:\SymCache*http://msdl.microsoft.com/download/symbols;srv*e:\symbols
*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 7 Kernel Version 7600 MP (8 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16617.amd64fre.win7_gdr.100618-1621
Machine Name:
Kernel base = 0xfffff800`02c57000 PsLoadedModuleList = 0xfffff800`02e94e50
Debug sessio... Read more

2 more replies
Relevance 78.72%

I am just coming off of panic mode. Thank goodness I backed up this morning off schedule. I am posting because I need advice of what might be causing this.

First
Running Vista Home Premium German (sorry I am just a user, not in geek at least when it comes to Windows)
I tried to install Service pack 1 yesterday but it was taking so long as if it were hanging, so I clicked cancel and then the progress bar filled up anyway and it is listed as installed unsuccessfully. I think it left an irritant in the system...

Hardware
Samsung laptop (NP R55) duo-core 1.6 GHz, 2 MB RAM, bought March 2007 - heavy use in relatively dusty environment. Sometimes overheats (?) and switches off automatically when running video files (e.g., youtube, DVDs)

Symptoms

Yesterday (and probably after the failed service pack install), I woke the laptop up from sleep and it beeped very loudly I believe twice but the machine worked. During an evening of work, I put it to sleep and woke it up several times without problems. I worked all this morning without problems. Put it to sleep for lunch, came back, tried to wake it up and it beeped loudly twice and hung before even getting to the cursor. Restarting several times, got the same beep and not even the welcome window. Panic Panic. (lots of deadlines!). Turned it off, got on very old Mac to google for help, signed up on this forum, spent 10 min trying to find backup disks (found!). Started it to see if it would work - yeah! It came on (though com... Read more

Answer:Loud beep, hung startup scare

Does no one have any advice for me???

I worked all evening and turned it off. This morning it started fine, read my mail, put it to sleep, came back an hour later and now the whole thing has started gain.

It gives 1 long beep and 2 short beeps and will not start up the recover disk :(((

7 more replies
Relevance 78.72%

Since installing a new hard drive in my Pico Desknote Pentium II 333Mhz laptop there is a very loud beep a couple of times when booting up. How do I kill this noise without losing normal sound once in Windows 98SE.

Answer:Laptop loud beep on startup - how to stop it

Assuming that there's nothing indicated by the beeps that is wrong then you may have an option in the BIOS to disable startup sounds.

4 more replies
Relevance 78.72%

Recently I have encountered a problem with my computer where everytime I press the "Power" button, it makes a very high-pitched beeping noise,(very annoying). I opened my computer and everything seems to be running fine. The green power light is on, on the motherboard, my CPU and other fans are spinning fine.
- Also, I'm embarrassed to not know this but, is the graphics card fan supposed to be spinning all the time, or just when it gets to a certain degree point? If it is supposed to be spinning all the time, then it's not working.

*Is this a beep code, because I have not yet found something from American Megatrends that fits this description.

BIOS = American Megatrends
GPU = Nvidia 8800GTX
CPU = Intel Core 2 Duo E6700
MB = Asus P5N32-SLI SE
 

Answer:Loud High-Pitched Beep Upon Startup

This may help - http://www.techspot.com/vb/showthread.php?p=288180#post288180

The gpu fan spins all the time on all the cards I've ever seen.
 

12 more replies
Relevance 71.34%

Hello, I need a bit of help as I want to buy the:

Gainward GeForce 6800GT 256MB GDDR3 AGP8X, "Ultra/2400",2ns,DVI, Retail

I know quite abit about graphics cards and understand the item above apart form: "Ultra/2400", this card is not a Golden Sample or a GLH card. So what does it mean?

Thanks for any help...

Alex
 

Answer:Gainward GeForce 6800GT 256MB "Ultra/2400" 2ns

It will be useful if u can post alink to that card, i will exactly let us know what u r looking at.
 

7 more replies
Relevance 63.55%

Hi, I have been using the Y480 for almost 2 years. However, when I boot up this morning, it just beep beep beep continously. and the screen just have a cursor blinking. But after I reboot again and press F2 to enter bios, and then quit bios settings, the notebook can be boot up successfully. I have backup everything I need What should I do to fix the error? Is my harddisk gonna be failed? I have lost all the purchase receipts but I have registered 2 years ago. Thanks!Peter

Answer:Y480 continous beep beep beep during startup

Beeps are error messages from the Motherboard. Either the MOBO is failing or you have a problem with your RAM, I dont think it is related to your HDD, but you should create a backup. Also, if you don't have, please create recovery disks immediately. You may want to do more research depending on the BIOS manufacturer and the beep codes. You can google these terms and you should find information on the procedure to validate this. You can also try to re-seat the RAM, maybe it got a bit unsettled, if you moved the laptop. All in all, if you took the externded warranty and you are still under it, you may want to send the laptop to Lenovo for repairs.

1 more replies
Relevance 63.55%

I am helping a friend who does not know anything about computers.  I looked up the specs and discovered this laptop can have a max of 2GB of RAM.  It has a single slot with 512MB module in it. The spec call for533Mhz front side busDDR2 SDRAMM533 / PC2-4200 1.8V I ordered and installed a Kingston HyperX Performance 2GB module with above specs. When booting, there is a 1-3-3-1 Beep sequence and no video.  Any Ideas please? 













Solved!

Go to Solution.

Answer:Lenova Thinkpad R52 Model: 18605EU Mem Upgrade Startup Beep Code 1-3-3-1

UPDATE: Went online and discovered the POST code 1-3-3-1 means "Auto Size" or "28 Auto Size"Went to uTube and saw video to disassemble the R52.  http://www.youtube.com/watch?v=da3ZGyS88GcOpened the case and saw the 2nd slot, which also had a 512MB module.  A spec did show "2 Slots" with 1 empty.So I took it out and placed the 2GB in. Now there's only 1 module.  I will update the CMOS battery (CR 2032) while inside then reassemble and Update the message again.Thanks.

5 more replies
Relevance 63.14%

Hello,

I have read many other post on this subject but none fit my exact problem,

Specs:
Intel i5 2500k quad core 3.3GHz
8GB DDR3 1333mhz RAM
NVIDIDA GTX 570 Graphics card
Asus P8P67 LE Motherboard
Windows 7 64 bit
60GB SSD/1TB Data hard drive
700 W Xigmatec power supply
Zalman Z9 plus case (In case that becomes relevant)
The problem began slightly more than a month after i bought my pc,

I was playing a game (Team fortress 2) when the graphics began to act odd, for instance when something moved past me it would seam blocky and out of line for a second,

i have checked two other games since,

when i start one (Killing floor) the moment i reach the main menu my pc makes a continuous beeping noise and when i exit the game the beeping noise becomes lower pitch while exiting, then stops once the game has closed.

When i start the other game (Counter strike: source) there is no beeping noise but i get the same graphics problem as i did when playing the first game (Team fortress 2)

The temperature displayed on my case is usually between 22C and 25C and was at 24C at the time when the graphics problem began.

Thanks,
Jesse
 

Answer:Continuous beep from pc during use

16 more replies
Relevance 63.14%

Had new PC for a week, MaxData Athlon1800 XP, installed an anti- virus, couple of games and an old hard drive to get some files, I've since disconnected this in case it was the problem, when on Sunday I switched on and I get this constant tone from the tower. Someone told me to go into BIOS and choose optimum settings but this hasn't cured it.I have used system restore to jump back a couple of days and I've reinstalled XP but it is still there. It did stop for about an hour when my daughter was playing music on it but it was still there come start up later.

Answer:Continuous Beep from PC

Bleeping usually means that the Bios/MotherBoard has detected a problem in POST, usually memory. try setting Default settings and/or test the memory and make sure all your connections are secure.

9 more replies
Relevance 63.14%

Hi I have been at this problem for a day and have no idea what to do.

I boot my system and I just get an alarm sound beep. No pauses no pattern just a beep which doesn't stop. I am still able to use the PC (on it now) as for the beep I just removed the motherboard speaker lol.

I have checked loads of Forums but can no find anything helpful. Looking at My Computer temperature they all seem average for my system plus the beep happens straight away during the system post.

I have taken my Ram and Graphics card out and both are fine. I have also taken my CPU out where I had a little problem. When taking the Heat sync off it pulled the CPU with it stuck to the heat sync like concrete. This in turn bent about 5 of the pins VERY VERY slightly like 0.01 degree angle. How ever the beep happened long before that. I have re-pasted the heat sync and the pins are back in place and be evidnce type right here right now all seems fine apart from the beeping.

I could just ignore it but I am big time gamer and I don't feel combatable playing any game right now till the beep goes away and leaving the motherboard speck out means I lose overheat warning.

It did beep about a month ago it did it for a minute and stopped I had it last week and a reboot sorted it however this does not work no more.

I have made 6 systems and non of them have had any problem's. This system I made about 4 Months ago and is my latest all new hardware (sept for the hard drive which is a month older) My... Read more

Answer:One Continuous beep

14 more replies
Relevance 62.32%

The PC speaker just beeps when I power on my computer. Nothing happens just one long continuous beep. HELP!
 

Answer:One long continuous beep

Usually memory or video card.
Try reseating your memory or trying just one module at a time.
Try your video card in another slot.
 

2 more replies
Relevance 62.32%

Greetings all,      I have acquired (a friend found it next to a dumpster while taking out his trash) a self built computer case contents include: MSI P6N MOBO,  Geforce 8800GTS graphics card,  Enermax 500watt PSU, Lightscribe DVD RW and 2 OCZ  PC2 ram sticks (no HDD).  The front panel button was not connected to the MOBO.  Upon connecting the switch and turning it on the fans come on but the MOBO emmits a continuous beep.  I have downloaded the manual for the MOBO but Have yet to find any information on what this means.  I assume the owner (who is likely a gammer and more knowledgeable than I) felt it wasn't worth fixing, but I thought it might be a (fun ?) project if it's feasible.  Thx in advance for any feedback.

Answer:MOBO continuous beep

Quote from: glathem40 on March 03, 2013, 08:48:33 PM...(who is likely a gammer and more knowledgeable than I)...Most gamers know nothing about hardware; too focused on the games.Continuous beep could be anything.  Remove the CMOS battery & short the terminals, if it has any.In order to POST, you need 1 RAM stick & keyboard.  Connect monitor to see if anything is there.MSI P6N is Intel Socket 775, not the latest, but still in use today.  RAM is DDR2 which is getting expensive compared to the newer DDR3.This looks like it.

6 more replies
Relevance 62.32%

I have A7V600x mother board with a Athlon XP 3800+...its been working find and all the sudden the computer does not turn on at all with a long contentious beep....we always had a problem with the video card so we thought it was the video card problem but replacing did not solve the problem....we still get the continuous beep like beeeeeeeep beeeeeeep each beep is about 2 sec....I try looking online but nothing really helped...wat could be the problem??

Answer:A7V mobo continuous beep

Athlon XP's only went as far as 3200+

a beep like that is usually memory or cpu, at least that is what is the listed cause for the code. it can however be caused by a number of things which could cause the motherboard to stall early in it's POST (Power On Self Test). if it's not CPU or memory i would guess it's related to the power supply, either the power supply itself or it's connection to the motherboard

3 more replies
Relevance 62.32%

Help me out... I'm working on a friend's computer. I was in the process of installing more ram, 128k pc100, and upon installation, the computer will no longer boot up, will only give me a very anoying continuous beep. I'm not sure what type of bios it is. I'm going to attempt reseting the bios by removing the battery. If there are other solutions, please enlighten me. I'm at a lose and need guidance....thank you very much....
 

Answer:continuous beep, no bootup

Welcome to TSG! Continuous beeps usually mean bad ram. Will the machine boot if you remove the upgrade and put in just the old ram?

Let us know
 

3 more replies
Relevance 62.32%

I have this computer running xp pro that is giving me a strange error. Back in the shop where the computer has been sitting for 8 monthes and running fine up until today,

On startup while still loading BIOS I get this alarm sound. It is a contiuous alarm. No error messages, the Bios just stops loading and stays in one place.

What is weird is I bring it into the office plug it in and it works fine.

I have tried multiple outlets back in the shop but still to no avail.

Does anybody know what the continous alarm sound might mean when starting up the Bios?

Answer:Continuous beep on start up

Please have a look at the Power On Self Test Beep Codes,
and post back which beep sequence best represents your own issue.

9 more replies
Relevance 62.32%

Hello There, I have lenovo B450. My laptop is makeing continuos beep noise while booting. So i used to shut down it. After that when i start, it doesnot make any noise. What it reason for this??? Please help me...

Answer:Continuous Beep while booting

Hi
 
Welcome To Lenovo Community
 
You may please try changing the speaker settings > level > PC Beep ? It should be at  kept at 0
 
 
 
Hope This Helps
Cheers!!!
_______________________________________________________________________________________________
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
 
Did someone help you today? Press the star on the left to thank them with Kudos!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!  This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
 
Follow @LenovoForums on Twitter!

1 more replies
Relevance 62.32%

Hi there, first off, Im running Windows xp OS. I recently got Rosetta stone software and I've installed it and everything. It has voice recognition capabilities and when I get to the point where I set up the mic, each time I try it says that it was unsuccessful. I am using the usb headset that came with the software. So, I pull up 'ol Windows sound recorder to see if the mic is picking anything up, and it is, except that when playing the recording back, along with whatever I said into the mic, there is a loud continuous beep. It is only present while playing back what has been recorded from the microphone. I am assuming that this is why I can't get the mic setup in Rosetta stone to complete successfully, because not only is it picking up my voice, but also the loud high pitched continuous beep.

I have speakers connected to a Sound Blaster Audigy card, but the beep is still present if I disconnect the speakers. I've also tried the usb headset in multiple different ports and the beep is still present whenever i record something and play it back.

Any ideas? Much appreciated
 

Answer:Continuous beep when using a microphone

I wonder if the microphone volume is set too high. Have a look at:

Control Panel>Sounds and Audio Devices>Voice tab

and click on Test Hardware.

In there, the microphone volume will be set automatically (I'm pretty sure that's how it works), and it might be a good place to visit anyway, just to make sure everything is OK.
 

1 more replies
Relevance 62.32%

I have been running Windows 2000 Pro for a little over 5 months now. Just recently I have been having a problem with the default beep (or any sound) on the computer. If I restart I do not hear anything until I open a program or click on something that makes the default beep sound. Then my computer goes haywire. All I hear is the beep over and over and over again, really really fast. This is very confusing and very frustrating since I can't hear music anymore and I have over 40 gigs of MP3 files. I can turn off the sound by MUTING the volume control, but this is not the correct fix, it just shuts up the computer. Please help!!!!!!!!!!!!
 

Answer:Continuous Default Beep...

Open media player, click view,options, playback tab, take the check out of repeat forever and see if that helps. Don't know if it will but I don't know where else to tell you to look either.
 

1 more replies
Relevance 62.32%

I posted this elsewhere and have since discovered that place was inappropriate; sorry.

Fixing an old machine, p3 phoenix bois, and it boots with a single beep, and seems fine until it initialises the keyboard. What transpires i can only describe as an angry successive beeping that develops into a seemingly continuous beep. The background is bizare, at least as far as i understand it, a client brought in 2 machines, the first had swolen caps on the board, which we replaced, and ran successfully for some time. However, the keyboard began to stutter with beeps after post and after re aligning the pins also worked fine. Subsequently, the client brought the first back, the keyboard had begun beeping again, only with more intensity and irregularity, simmilar to a stuck key but more erratic. I sent the client away with a new keyboard and success. However, the client returned again, reporting that the beeps had begun again 4 or 5 days later. Again I replaced the keyboard with, and no beeps. Subsequently the client brought in a second machine reporting that the first had persisted with its beeping issue, and that he had chosen to use another machine at his disposal. As it turns out the second computer had the same issue, solved at least initially with the replacement of the keyboard. The problem still persists however, and seems to have gradually worsend over time. In both cases the same original keyboard may have been used by the client, in the case of the first machine the keyboa... Read more

Answer:Continuous Beep After Post

You sure this client isn't messing with you and has somehow caused this? Are there any *.bat files or something similar that have some code in them to cause this? I guess last but not least, is this an error code that the bios is throwing you due to heat problems or something of the sort.

Just seems a little suspicious.
 

9 more replies
Relevance 62.32%

My PC base unit makes a deafening continuous beep once in awhile.The only way to stop it is to reboot but even then it can reacur after awhile.Some days it'll work without any problem.I've noticed some programs can sometimes trigger the noise such as defraging and Norton Antivirus.Anyone else had this problem ?

Answer:Continuous Ear-Piercing Beep???

When you reboot does the beep continue after a short while if you immediately use CPU intensive programs?This sounds like your CPU is overheating and your BIOS is shutting down the PC.Please provide more information- make, model, operating system, BIOS etc.

9 more replies
Relevance 62.32%

Hi guys,

I'm wondering if someone can help. I keep having this annoying problem where my PC randomly just freezes up and emits this ongoing beep until I manually have to power it down.

My system specs are:
Model: Packard Bell IXTREME X6617 UK
Processor: Intel Core2 Quad Q8200 2.33Ghz
OS: Win7 Ultimate (Service Pack 1)
Memory: 6GB
Graphics: ATI Radeon HD 5670
I have ran a full Memtest on bootup which reported no problems with the RAM cards. I'm at bit of loss here now though and any help would be greatly appreciated.


Many thanks

Ash
 

Answer:PC freeze then continuous beep

7 more replies
Relevance 62.32%

when i tried to boot up my pc all i get now is 1 long continous beep what does this mean it is a aopen mobo

Answer:continuous beep from motherboard

Power supply, system board, or keyboard problem

10 more replies
Relevance 61.91%

Hi,
My laptop here is a Dell Inspiron 15, 3000 series. 
The laptop itself works perfectly fine, I am able to get into windows (which I installed myself, it originally came with Ubuntu). 
Occasionally though, it will do a BEEP BEEP BEEP PAUSE BEEP BEEP BEEP PAUSE (repeats).
This happens on boot and sometimes when I am using it. Sometimes it turns off suddenly when I am shifting the computer around. It's extremely loud.

What is causing this? The sound seems to be coming from around the area the Memory banks are under the laptop, but nothing seems to suggest that anything is wrong.
I took a suggestion and used FN+Power to do Hardware Diagnostics which said nothing is wrong.

What else can I try?

Thanks!

Answer:Dell Inspiron 15 - 3000 series - Beep Beep Beep Pause Beep Beep Beep

Hi,
I’d suggest that you follow the steps mentioned below and check if the beep pattern repeats.

Switch off the computer.
Disconnect the AC adapter from the system.
Remove the battery from the computer.
Press and hold down the power button for 15 seconds.
Then connect back all the peripherals and check if the beep pattern repeats and reply us with the beep count.

If you still receive 3 Beeps on the system then it indicates System board failure.. You will have to replace it on the laptop.
Please let me know the findings.

3 more replies
Relevance 61.91%

Hi
I am getting beep sounds when i turn on my dell inspiron n5010.
Nothing is showing up other than beep sounds.
Please help me out
Regards
Ganny

Answer:RE: Dell Inspiron 15 - 3000 series - Beep Beep Beep Pause Beep Beep Beep

Hi Ganny,
What are the exact # of beeps in a cycle? 
Kindly review this chart and see page# 47 - it will help isolate the source of the issue. 
Based on the exact # of beeps, that part would need to be replaced.
Also, please click my DELL-username and write me a private message with the service tag and your Name for case records.
Let us know if you have any other queries.

2 more replies
Relevance 61.91%

Hi,

I have a Qosmio G10. It's worked fine up until recently. Now when I start it up, I hear a continuous beep. There is also no screen image.

Can anyone help?

Many thanks

Martin

Answer:Qosmio G10 - continuous beep on start up

I think there is a problem in the hardware configuration.
Did the laptop receive a shock recently?
The laptop beeps because the checks of the bios detected an anomaly.
What you can easily do is to check that at least the RAM is correctly inserted in its place. It happened to me once: I did not inserted correctly the additional RAM that I added, and the laptop beeped loudly!
If it does not solve the problem=> toshiba service.


Message was edited by: djfizz2

3 more replies
Relevance 61.91%

Boots up fine but no snooze button for this continuous alarm beep! Tried reseating RAM but that was no help. Also not a keyboard issue. Starts as soon as you hit the power button. Ran speedfan and don't see any obvious issues. Sweet gaming system, would like to get it back in action without the annoying beep for my nephew. Any help is most appreciated.

AMD Athalon 64 FX-62 dual core processor
2.81 GHz, 1 GB RAM

Win XP home 2002 service pack 2

Answer:Xp Continuous System Beep On Power On

your motherboard manual should tell you what it means

4 more replies
Relevance 61.91%

I just upgraded my system with a new Gigabyte K8NS Ultra-939 motherboard and a AMD Athlon 64 3000+. I have two DDR-2100 256mb sticks (planning on upgrading sooner or later). I placed them in slot 1 and 3 at first (read the manual wrong about running dual channel DDR). Just gave me the "Memory not optimized" at start-up. Well I installed windows and got the computer up and running. Turned it off and switched the ram stick in slot 3 to 2. Started the computer and got the nice "DDR dual channel enabled". Neat. Well, right before I got to the Windows loading screen the computer starts a long, continuous beep. It lasts for about 5 minutes then turns off for 2-3 minutes, then does it again (keeps repeating). I look up the beeping code in my book and it says 'DRAM Error'. I did a little bit of research on the internet and supposedly that error means the DRAM is not installed correctly. It is installed correctly though. hehe

I checked dxdiag and it is showing 512 ram. Everything runs fine but I just have that long beep which is extremely annoying.

Any ideas?

Thanks!
 

Answer:DRAM Error (continuous beep)

I'm confused, does the beep occur while the system is otherwsie operating normally and recognizing the full size of RAM? Or does this happen during POST?

Most dual-channel motherboards have more than one way to activate dual channel, you might be able to try more than one combination to get it working.

For DDR to work in dual channel they need to be matching pairs of sticks - same brand, model number, speed, and timings. Much like running dual processors. Sometimes you can get two different brands working but not usually...even then, sometimes two generic sticks of RAM or certain brands just don't run in dual channel. It isn't an industry-wide tech by any stretch.

The only other thing that I could think the motherboard might be complaining about is the frequency or maybe the timing of the RAM. Both of those these can be adjusted through the BIOS.

Good luck and keep us posted!
 

2 more replies
Relevance 61.91%

I've just attempted to install some more DDR memory into my Compaq Presario S5600 desktop PC. To install it I had to remove the power connections for a few drives and unseat the graphics card. I reconnected everything, but when I turned the power back on there is a continuous high pitched beep, the lights come on but nothing else happens. The power connections and graphics card all appear to be correctly positioned. I also removed the new memory and I'm still receiving the same continous beep. What does this mean?
 

Answer:Added memory - now continuous beep

I feel a complete plank.

Had a coffee, went back and rechecked everything to find I'd not connected the power supply to the graphics card!

Oh well, it's all back up and running now.
 

2 more replies
Relevance 61.91%

For a while now I have been having a problem where if I am in a program (seems mostly to be in games that want lots of resources) my computer will suddenly freeze and an awful buzzing noise will begin to come out of my speakers(NOT from the case). I saw a post about something like this from a previous user, but he said that the noise came from his case speaker, so it seems that mine is different. My system specs are as follows:

Athlon XP 2100+
GeForce4 Ti4400
512mb RAM
80 GB HD
Audigy Sound Card

And her is my DXDiag:

------------------
System Information
------------------
Time of this report: 5/18/2003, 19:14:21
Machine name: PHELPS
Operating System: Windows XP Professional (5.1, Build 2600) (2600.xpclient.010817-1148)
Language: English (Regional Setting: English)
System Manufacturer: n/a
System Model: n/a
BIOS: Award Modular BIOS v6.0
Processor: AMD Athlon(TM) XP 2100+, MMX, 3DNow, ~1.7GHz
Memory: 512MB RAM
Page File: 77MB used, 1173MB available
Windows Dir: C:\WINDOWS
DirectX Version: DirectX 9.0a (4.09.0000.0901)
DX Setup Parameters: /Silent
DxDiag Version: 5.03.0000.0901 32bit Unicode

------------
DxDiag Notes
------------
DirectX Files Tab: No problems found.
Display Tab 1: The file nv4_disp.dll is not digitally signed, which means that it has not been tested by Microsoft's Windows Hardware Quality Labs (WHQL). You may be able to get a WHQL logo'd driver from the hardware manufacturer.
Sound Tab 1: No problems found.
Music Tab: No problems found.
Input Tab... Read more

Answer:Buzz or Continuous beep and freeze

6 more replies
Relevance 61.91%

Lately my computer has been giving me trouble.

It usually happens when I am playing a game online, I havent noticed it during offline activities/play. This seems to only happen during the hot summer. Here is my problem:
About 5-10 minutes into a game, my system will freeze and the system will put out a long continuous high pitch noise(beep). I used to think it was just because it was getting too hot inside the system, but I now have windows open and extra fans blowing so that is not the problem. Then I thought it was a video card problem, but it would mean that it only malfunctions during the summer. Now I think it has something to do with the power supply. I read in a book that the long continuous POST error code meant a bad power supply and that I should exchange it.
Before I go to the trouble of buying a new one and putting it into the computer, I was hoping that someone could give me some ideas as to why the system is doing this. Here are the specs to my system:

Asus A7A266 Motherboard
AMD Athlon 1.2 GHz CPU
3x 512 MB PC 133 DIMMs (1.5 GB RAM)
60 GB Maxtor 7200 RPM HD (C:/ & Windows 2000)
80 GB Seagate 7200 RPM (D:/ & Windows XP)
(I use dual boot, and always use Win XP.)
Inno3D Kyro II 64 MB Video Card
Soundblaster Live! Platinum Sound Card
8x DVD-ROM/CD-RW Samsung Disc Drive
32x CD-R Pacific Digital CD Burner Drive
Linksys 10/100 Network Adapter
300 W Power Supply (i think this is the problem, i think i need a 350).

As I said before this only happens durin... Read more

Answer:one long continuous beep during play

It really does sound like a overheating problem. Are you using the Asus Probe software to give you an idea of its base running temp vs the temp after heave game play? If it goes up 10+ degrees, that would be another hint of heat problems. If you have had the system running for awhile, pick up a can of the compressed air and carefully clean out the dust on the CPU fan blades and all other fans in the system. Clean off dust on the video card and every thing else at the same time. Dust acts like a fur blanket and raises temp on all surfaces. As it builds up over time, fan efficiency declines. Try moving the computer away from a wall that may raidate heat and make sure all the internal cables are bent to allow the best circulation of air from the front of the case to over the cpu fan and to any rear case fan and the power supply exhaust fan. Remember that space is needed behind the tower to help move the heat away. I have a similar system Asus A7A266/AMD 1.33ghz/512 mb ddr, Cd-rom, Cd-RW, 2 WD hard drives dual booting Win98se/W2kpro with Creative Audigy Platium, Modem, and Nic card. That fills my mid tower case and lately in Michigan the temps have been in the 90s often. Unfortunately that computer is near a South facing wall that for kicks i put a thermometer up next to it and was amazed to see an area temp of 111 degrees near it. I use a Thermaltake MiniOrb which works great until it gets hot like lately. Fortunately, i just take of on side cover and put a small fan blowing acr... Read more

2 more replies
Relevance 61.91%

Hello. I turn on my computer and starts fine but after 7 seconds it does a continuous beep and it just turns off, I think i know what it might be but i want some other oppinions, OK i opened my case took the heat sink off and looked at the heat sink for dust because it might have been over heating then i discovered that the thermal compound (ceramic) was patchy and lost in some places, just like flakey wallpaper but some missing in places not a circle shape and i put the cpu back on and yeah, im thinking if i should get some more thermal compound i was thinking of Artic 5 silver But i dont know if its safe Because this is my first computer and im not a Tech Head,Maybe the cpu is not the problem or maybe it is:confused.

Thankyou...

Intel pentium 4 (3.0ghz) (1GB RAM)
GIGABYTE GA-8i915P SERIES (SUPPORTS LGA775 Intel pentium 4 processor)
NVIDIA 6660 (6 series)
 

Answer:CONtinuous Beep and AUto shutdown

its possibly heat related do you know how to enter the bios

if so can you check the temps?

when you start the pc is the cpu fan working?
did you have this problem before you removed the heatsink, are you sure you have replaced it correctly.

usually pentium 4s have adequate thermal protection on retail heatsinks, is yours retail or aftermarket?
 

11 more replies
Relevance 61.91%

A Acer desktop was dropped of with me with the discription being it wont start up and it beeps. After futher investigation: When you power up the system the fans start then stop then start. Then no boot screen or anything just one continuous beep. I was able to get it started up once by clearing the CMOS and reseating the Ram, but that won't work for some reson now. Either it's a virus or the Ram is not sufficant or bad. The system is running Vista 32 bis. with only 1gb of ram which if that was all might work, but they are also running Quickbooks 07 and a few other heafty programs. any sugestions

Answer:Continuous solid Beep will not Boot

Hello Ahudek,
Remove all the ram and try one stick at a time, see if that does it.
Also check the connections to the graphics card/cards.
It does sound like a memory problem, but i got this when a power lead to a graphics card went bad.

3 more replies
Relevance 61.91%

I have a 4 year old T60p type 2007-B49.  This morning when I went to wake it up, it emitted a one long, continuous beep and did nothing on screen.  After a few seconds, I powered down.  I started up, it went to the Windows XP splash screen and gave out a long beep.  Scared, I powered down again. Powered up in Safe Mode, got a bunch of gibberish (safe mode has always been janky on this machine).  Powered down, shook the machine around (see below), powered up in Last Known Good, and it was fine.  I'm working on it now. But I want to figure out what happened.  My suspicious is the fan.  Here's why: 1. I had a fan go out half a year ago ("Fan Error" at startup, no boot).  I replaced it.3. Two months ago, I took the laptop on a trip.  When I got to my hotel, I got a "Fan Error" message.  When I returned home, everything was fine.  Something must've been jostled loose one the outbound trip and jostled back into place on the return trip. However, I did NOT get a "Fan Error" this time, just a continuous beep.  The beep sounded like the beep emitted by my PC when the CPU overheats, also leading me to think it's the fan.  My CPU temps are at 53c right now.  I don't know if that's normal or not for a laptop.  Thanks for your advice in advance

Answer:continuous beep at wake up -- fan issue?

53 degrees idling in a T60p is not considered abnormal. download, tpfancontrol and play with the various fan settings, see whether the fan do anything abnormally. 
 
A new fan/heatsink costs around 70 USD, so it is not that terribly expensive. 

1 more replies
Relevance 61.91%

Hi there,

My PC:
Dell dimension 9200

Whislt booted in windows XP, randomly the PC will freeze and 1 continuous beep comes from the motherboard. I have to turn off the computer and boot it back up again. There are no beeps during boot up.

Before windows freezes, each program I am running slowly stops working.
I.E.
I can chat on MSN messenger for abit until eventually it stops working.
When I right click on the desktop the menus appear semi transparent.

After that everything freezes and 1 continous beep comes from the motherboard.

I have not installed any new hardware or software. It just happened randomly.

I have 2 1gig ram, I tried using only 1 of those each to see if it could be the memory but the PC still crashed regardless of the memory stick I use. Though this doesn't rule out the possibility that both memory sticks are broke (unlikey though?).

I tried replacing my graphics card, it still occured. I ran the hard disk diagnostic which said they pass.

I checked that all cables were fitted correctly and refit them just encase.

Tried to install windows again using windows recovery, which took ages cause the PC kept hanging, so that obviously is a hardware problem.

I can only assume it is either the Power supply or the motherboard. Though I could be wrong and it could be both memory sticks.

Hoping it is the power supply because i've heard replacing a motherboard with a dell pc is not easily possible. The pc has ran out of it's warrenty.

The bios does... Read more

Answer:Windows XP freezes and 1 continuous beep

Have you checked to see if you have the "stickey Keys" feature turned on or have you tried a different key board? either could cause the described problem.
 

1 more replies
Relevance 61.91%

I recently purchased a used Acer Aspire One netbook. The netbook I opted for was the 8.9 inch screen, 160GB harddrive, 1GB RAM version that come installed with Windows XP.

So, the other night I get a virus on it that makes it so I have to buy this company's spyware blocker or I can't even browse the internet. Antivirus Live I believe it was. So, I followed a tutorial on bleepingcomputer to remove it. I did this successfully. But then, my computer started freezing up and then crashing while browsing the internet. This was followed by a loud beeping noise that continually played until I either hold the power button or yank the battery.

So, I say screw it and freshly install Windows XP off the partition on the harddrive and the problem STILL happens. I have no idea what is causing this, but I think Antivirus Live should be liable.

Anyways, any help would be appreciated. I just got this thing and was loving it until this happened.

Answer:Freeze and long continuous beep

Nobody...? Please help me!

8 more replies
Relevance 61.5%

Okay so i downloaded a program that is an alarm clock that plays an infinite beep until i turn it off. it plays the internal beep, and my friend has it and swears by it to wake up. problem is, i can't turn up my internal beep past a pleasant volume. i know this seems nuts, what with everyone trying to turn off that annoying beep, but i need to know!

How do i turn UP the beep?

I have the volume settings on the control panel all the way up. Not loud enough. and i'm not deaf and its not very loud. just a quiet little beep. I want this up to at least obnoxious. i wrote a program in high school that allowed me to adjust the pc beep, but damnd if remember any of that. so anyways, can it be done? also, the internal beep is NOT routed to my speakers. if there is no way to turn up the beep, is there a way to re route where it comes out? since i can always just make my speakrs loud as want and all.

thank you

dirty t
 

Answer:Beep not loud enough

have i stumped you all? is there no answer? if so, anybody that is confident that there is no solution, please post a reply saying so, that way i stop checking on this thing. or if its so simple that you feel i am retarded to ask, feel free to berate me in your response. i can handle it.
 

1 more replies
Relevance 61.5%
Question: One Loud Beep

I was training one of by co-workers on using Remote Assistance, we both were on windows messenger and everything was going well, during letting him take control of my computer it burped out one loud beep. I was on my laptop and have not been having any kind of problems at all, running with a chill pad so overheating should not be an issue. I have studied some beep codes error messages before but never ran across this one. Maybe someone could help me out and let me know if any similar experiences ring a bell or loud beep in this case.
 

Answer:One Loud Beep

After doing a Spyware scan it came clean

After doing a Virus Scan it came back with the following
File - kernel32.dll - Result/Infection - Change - Path c:\windows\system32\kernel32.dll

File - ntoskml.exe - Result/Infection - Change - Path c:\windows\system32ntoskml.exe

I have not heard the LOUD BEEP again since the remote visit after hours of use.
 

1 more replies
Relevance 61.5%
Question: R61 - Loud Beep

HiWhen I close the lid (to turn off the laptop) there is a very loud "computer" beep (i think i may also get it on startups). Is this normal? Its VERY loud.Thanks

Answer:R61 - Loud Beep

Hello, I just came upon your post looking for a solution.  I think I have found one myself... Open up the ThinkVantage ProductivityCenter, go to power manager [advanced],global power settings.... Then uncheck the box "Beep when power state changes" I'm hoping this solves the problem. Cheers

3 more replies
Relevance 61.09%

Hi guys!

First of all, I'm new here. I signed up to this forum because of an issue with my little brothers's PC. I've found some threads about the issue but I wasn't able to solve it with the given information.

So, my brother is just playing a game and all of a sudden his PC gives a long beep, and starts rebooting. Unfortunatly after this incident the pc won't start up at all, it's just giving this never ending beep.

knowing that he has an Asus p5n-mx MoBo and an Award BIOS I starten looking for answeres.
The error should indicate that there is an issue with the installed RAM. So I removed it and replaced it with a spare strip. But that didn't solve the problem. So I took out the Videocard and tried to use the onboard chipset to boot up. Still got the continuous beep. I removed all the RAM and tried to boot up. The result of that the 1 long beep and 2 short beeps error code as repeating loop. Now I am not sure if that is the indication for a not properly installed VGA card but it said so in the beep-code list.

Pc specs:
Asus p5n-mx motherboard
Award BIOS
Intel duo core E7300 2,66Ghz
Corsair 1024 MB DDR2 667Mhz RAM (2x)
320 GB 7200 RPMWestern digital HDD
ASUS EN9400GT 512MB VGA card
Windows XP Home Edition
It would be great if you guys could help out with this one!
 

Answer:PC wont't start up except for a long continuous beep.

16 more replies
Relevance 61.09%

Hey all,

I just recently got a large hardware upgrade (new mobo, video card, psu, RAM) and have run into problems getting things up and running. Here are my new specs.


Asus P5N-D 750i
OCX GeForce 8800GT 512MB
OCZ DDR2 PC26400 RAM (4GB package)
Corsair TX 650W Power Supply
Note: Using an Intel Pentium D 2.66 mhz processor from old system

I had a friend who is very experienced with installing computer hardware come by and over-see the installation. Everything was double checked that they were installed properly. When we powered on the system we got a long continuous post error beep coming from, i assume the motherboard. We tried disconnecting the RAM (didn't have another stick of working compatible DDR2 RAM to test with) and still got the same thing. My buddy seems to think my CPU may be the problem, as the video card was tested to work fine.

I guess i should also mention that last week i had a PSU malfunction that may have fried my old motherboard, so there is definitely a possibility that the old PSU also took the processor with it as well... Anyone have similar issues or know what a continuous loud post error beep on an Asus motherboard means? Any help would be greatly appreciated.
 

Answer:Long continuous post error beep!

Well it depends a bit on what BIOS you have what a continuous beep can mean but in general it means there is a memory error but can mean a system board failure or even a PSU failure.

So what BIOS do you have?
 

4 more replies
Relevance 61.09%

my asus a8v deluxe based computer works fine, completely funtional. however, ever since i built it, whenever it is turned off, the motherboard will eventually start making a continuous beep that never stops until i turn the computer on again. whats going on??
 

More replies
Relevance 61.09%

Hey I am working on my girlfriend's desktop, it's a 1-2 year old Sony Vaio and the problem is when I turn it on, the fans all run fast, then they gradually slow down, and then I hear a "beeeeeeeeeeeeeeeee" continuously from the inside. I have the covers off and checked all the cards and pieces to be sure everything is seated properly. Her parents had a new power supply put in and it still does the same thing.

Not sure what to try next. Any help let me know, thanks!

How i should include that she says every once in a blue moon it will turn on exactly normal and work fine. Thanks.

Answer:Sony Vaio Desktop Continuous Beep

Have you tried clearing CMOS by chance?

if you don't know how: unplug the PC from the wall. press the power button a few times to discharge any remaining power in the PSU. Remove the small silver coin battery on the motherboard. Leave it out for about 5 minutes. reinsert the coin battery, plug the computer back in, and turn it back on. See what happens then. If it still gives you the beep codes, try to find out what BIOS it has on it, and use this to help you figure out what the beep code means:
Computer Post / Beep codes

9 more replies
Relevance 61.09%

My son's PC crashed whilst he was using it the other day and he had to hard shut down (holding in the power button). Now it will not start, it simply gives a continual beep and shows a black screen with a flashing cursor.
The pc has an Intel i3 processor, an ASUS P8H61-M LE motherboard. We have already tried new RAM sticks in case the RAM had failed but that made no difference.
Any ideas - could it be hard drive failure? How can we tell?

Answer:Continuous beep and black screen with cursor

More likely to be a component failure than HDD. Beep codes should point to exact problem, listen carefully, does it match any of those listed below?
One short beep - VGA detected, No keyboard detected
Two short beeps - When using Crashfree to recover BIOS, the new BIOS is successfully recognized.
One continuous beep followed by two short beeps then a pause (repeated) - No memory detected
One continuous beep followed by three short beeps - No VGA detected
One continuous beep followed by four short beeps - Failure of Hardware component

2 more replies
Relevance 61.09%

Hi I just installed some new ram on my computer going from 1gb (2x512mb) to 2gb (an extra 2x512mb). The memory is all Geil 512mb PC2-5300. I have tried every combination I can think of yet whenever I have the new memory installed the computer wont start and there will just be a continuous beep from my motherboard (ASUS P5nd2 -SLI). I have sent the new memory back however it was sent back to me telling me it was fine!

Does anyone have any suggestions? I would really appreciate it, thank you!

Answer:Installed new ram, wont start, continuous beep

Post motherboard specs. You may need to adjust the memory timings to get it to work.

Check the motherboard manufacturer's combatibility list. Some RAM will not work, or will have problems with certain motherboards.

You could have a bad RAM slot on the motherboard.

You will need to test each stick one at a time in the same slot, to make certain they will all work with the board.

Are you absolutely certain all 4 sticks are exactly the same ?

Since the old pair works, trade them out for the new pair. If the are good, and exactly the same as the old pair, they should work in the old memory slots. If they do, move them to the (previously unused) memory channel and see if the new memory will work in the new channel. if they do, then the issue is not the new memory, but using more than 2 sticks at the same time.

Then focus on getting 3 sticks to play nice.

At some point things will stop working, and indicate the direction of the problem.

10 more replies
Relevance 61.09%

A colleague spilt water over an Equium A200 and as a result it beeps continuously at startup. Actually you get a beep, followed immediately by another. However, if you press F1 it boots up OK and all is well. I have run diagnostics and have found nothing wrong.
The only problem is that one or two of the keys don't work so well if you touch them lightly.

Anyone have any ideas about resetting the beep, or what else I might do? Thanks.

Andy

Answer:Equium A200- Continuous beep at boot

Hey,

I think it?s not easy to say why this happens but maybe the water has damaged the keyboard and so always a will be pressed? I don?t know it exactly.

I think it will not be so useful for you if we discuss about this here without testing it and we don?t have real facts so your notebook should be checked from a notebook technician. The guys can make a detailed diagnostic and order spare parts.

On the Toshiba website you can find a list of authorized service providers? Good luck!
:)

1 more replies
Relevance 61.09%

My laptop is making a continuous single beep when I turn it on. It goes to a black screen and won't load Windows. Tried f12 but nothing happened. How do I fix it?

Answer:Laptop continuous single beep when turned on

Unplug the system, remove or disconnect  the battery and hold the power button for 30 seconds.  Remove and reinstall both memory modules if they're removeable.
If that doesn't solve the problem, you have a bad main system board.
If you require further information we'll need the model information (i.e., XPS L322x, Inspiron N5110, etc.).

1 more replies
Relevance 61.09%

Howdy,
Windows XP student edition upgrade ... whatever
I'm running a Celeron 2.7GHz processor
Radeon 9250 excalibur graphics card
DDR 512 ram (x2), so a GIG.
Gigabyte mother board
Cyclone Power supply 400W
Vibra 128 soundcard
(if more info is needed please ask )

My computer has recently started freezing unexpectedly and the first occurances were whilst playing the only game i play, Counter Strike: Source. I thought it was just some random problem so i restarted and the computer froze when it got to the little 'windows is loading' stage with the moving bar. I freaked out and turned it off, and came back about 10 minutes later and the computer started up again fine.

I decided to test it a little running simple MSN and windows media player (WMP), and it works fine, no problems. I turned MSN and WMP off and logged into a server on CS: S, and about 4 minutes into the game the computer freezes, the screen blackens (sometimes retains the last image on screen) and the speakers output a continuous beeping sound, which can be ceased by turning speakers off.

Now, it's really scaring me because i'm on holidays and i've still got another week of nothing to do! CS is my last resort for boredem after my work, and it's a cheap way for someone my age to amuse themselves!

If you've ever encountered this before, please help me..

Thankyou.

P.S. This problem ALSO occured on my previous machine, i replaced mother board, RAM, Processor with identic... Read more

Answer:Unexpected Windows Freezing + continuous beep

8 more replies
Relevance 61.09%

Hi guys, i was trying to surf the net about 20 mins ago on my computer when all of a sudden the power just turned right off, i initially thought black out, but none of the other computers crashed. And then my computer tried to restart, and it seemed like the power kept on cutting on and off, so i turned the PSU off at the back, waited, turned back on and restarted and i just get the continuous beeps and the screen flashes a message saying i havent plugged in the power on my AGP. But there is lights on the AGP and everything else starts running. The fan on the graphics card runs and everything. I unplugged every cable from the PSU and reconnected, the AGP is still snug in its slot.

Computer is about 4-5 months old, all parts purchased separately and i installed, there has not been any problems until now.

Antec sonata 2 smartpower PSU, 450W which has only 1 PCIe power cable.
Gigabyte GA-965P-DS4 mobo
Gecube 1900XTXD-VIE3 512mb radeon PCIe.
Intel Core2 DUO E6600 2.4GHz1066MHz FSB 4MB L2 cache
300GB Western Digital HDD SATA2 7200rpm
2GB GSkill (2x1GB) DDR2800 4-4-4-12 (F2-6400PHU2-2GBHZ)
Benq 19inch monitor
Samsung 16xDVD DL oem Optical drive
Nortons Internet Secruity, updated when it booted, bout 15 mins before the crash.

Any more info you want i am more than willing to provide,
Thank you in advanced
Tom
 

Answer:Random crash, bios continuous beep

11 more replies
Relevance 61.09%

Hi, My Acer x3810 went blank screen with cursor and gave 1 continuous beep when I clicked on a file in my usb flash drive. Recovery process finishes when I run the recovery disks, but on restart goes back to beeping with cursor. It powers up and beeps continuously with blank screen. OS is Vista
 

Answer:blank screen with cursor and 1 continuous beep

Check the RAM with this memory tester: http://www.memtest86.com/

Click "Downloads" then click the first link in the list: ISO image for creating bootable CD (Windows - zip)

Unzip it and you will see an ISO file which is a CD-image file. Use IMGBURN to create a CD from the ISO file.
IMGBURN is here: http://filehippo.com/download_imgburn/

Boot your PC from the CD and run the test for at least five passes.
 

1 more replies
Relevance 61.09%

Hi,

This morning I removed my main HDD to plug it into another PC and transfer some files. I have now installed it back in the original PC, but it will no longer boot. There is only a loud, high-pitched sound coming from the PC. I have cleaned the inside thoroughly with compressed air. If I remove the graphics card, the sound is no longer emitted. I have had a lot of trouble recently with my computer, most notably with my monitor remaining completely white upon startup. Turning the monitor on/off about ten times tends to fix the problem and the monitor will then display normally until the next shutdown/startup. I tried the monitor on the second computer and the same thing happened with a white screen that would fix itself after being turned on/off repeatedly. My main concern at the moment is the loud whining from my first computer on startup. I am not sure where to begin troubleshooting any further: does this sound like I need to replace my graphics card, PSU, or something else?

PSU: HEC-550TD-PTE
Graphics: GeForce 8800GT

Any help would be greatly appreciated.
 

Answer:No boot on power up w/ loud continuous high-pitched noise.

First, the hard drive. Sounds as if you have messed up the Master Boot Record by connecting it to another PC. This can be fixed by I need to know the OS.

Secondly it also sounds as if your graphics card has failed or the fan on it is making the noise which will need to be replaced.

Finally as your monitor is producing the same fault on another PC then it needs to be replaced.
 

1 more replies
Relevance 60.68%

how can i fix or know that i have a malicious program in my PC?
Yesterday i was trying to burn a movie. First i have to decrypter and i used dvd shrink (i have been using this program for a year now) and after i back it up (100%) I heard a loud beep and then it shut down. I re-started 5 more time and try to do the same and i have the same output.
Can anybody please advise?
 

Answer:Loud Beep...then shutdown

More info ...what exactly happens ...how far do you get on the boot up ...do you get a boot beep?
 

9 more replies
Relevance 60.68%

I have a Latitude D630. I know how to use the audio controls through the control panel. However,  there is a default beep that occurs under certain circumstances. It does not seem to be possible to control the volume of this beep. It is some kind of primitive warning that occurs under  infrequent conditions. One such condition is when I am using applications through the internet and I create some sort of error condition. It happens so infrequently that I can't quite figure out the pattern of when it occurs.
The PROBLEM is that I listen to music on my computer through headphones while I'm working. I have the sound set to a low volume but this beep intrudes every so often and it is literally RUINING my HEARING because it is SO LOUD. (Okay, I could listen to my iPod instead of the computer, but sometimes the computer is more convenient.)
I am presently using the "Windows Default" sound scheme and I have this LOUD default beep problem. In the past, I've used "No Sounds" sound scheme and I still experienced this problem.
Can someone please offer some suggestions about how to control this default beep? Eh? What was that you said....? I am losing my hearing.

Answer:Eh? What was that you said? Default Beep is TOO LOUD

To turn off System Beeps:1. Open “Control Panel\System\Hardware Tab\Device Manager”. 2. At the top click “View\Show hidden devices” then go to “Non-Plug and Play Drivers” and  double click “Beep”. 3. Now click the “Driver Tab” and finally change “Startup Type” to “Disabled”.4. Restart.

2 more replies
Relevance 60.68%
Question: Loud Beep Noise

Hello all hoping you can help me first post here btw. I got some RAM for my computer. My computer is relativly new and is takes 2100 (speed of the RAM?) they guy at the store were i bought the RAM said i would be ok with 2700 cause he was out of 2100, i bought 512MB and the motherboard can handle 3gigs so i know i am in the clear there. I unplugged it all grounded myself real quick and installed the new chip, with the old one too. Now when i turn the computer on it just beeps real loud about every 10 seconds and what start up windows or anything, the monitor just says no signal. I checked everything like 6 times now. Plz help me i am pulling out me hair here.

Answer:Loud Beep Noise

Joker4302......Have you been able to remove the "new" ram and boot up with the original ram ?The pc2700 is probably backwards compatible ......however do the other specs match up with the original ram?dl65  

3 more replies
Relevance 60.68%

I have a laptop that everytime I boot up I hear a loud beep that continues until the Windows desktop comes on. At that point the only thing that I can find wrong is that my A key does not work. I tried to clean the keyboard thinking it could be a stuck key, but I had no luck on that. I am at a lost of what the problem is. My laptop is a Windows XP Pro with p4 2.6ghz, 1gig RAM, 40 gig Hard Drive. My understanding is that if it was a stuck key the BIOS would show that upon bootup. Does anyone have any ideas?

Answer:Loud Beep on Bootup

in laptops, F1 and sometimes ESC key (Depends On manufacturer) is used to opn BIOS controls, DEL on Desktops, f10/f11 on Intel otheboards and so on.

so as u said, that BIOS should open on startup-, isnt applicable, as this key would be someother than the one used to open BIOS controls.

now as far as this problem is concerned, have u ever got soem liquid split on ur keyboard? sa it happens tht keyboard circuitry works as in case a key is pressed, the circuit completes. and sent to system, so there might be a possibility that something might have got stucked between key board circuitry and keys,, and therefore though key shows that its not pressed but actually completing the circuit, that might be some of non writing keys, like ALT, CONTROL, F's, HOME) as if it has to be some alphabetic, then it should have started writing the moment u opeended some word program

download some key checker program, and see what key is being pressed.

and as well, blow hard on ur keys, may eb that thing gets out.

5 more replies
Relevance 60.68%
Question: Single loud Beep

Hey all,

So I was playing World of Warcraft and all of the sudden a single, loud beep emitted from my computer. Nothing like this has ever happened before. I know that when a computer beeps as such it is usually trying to tell you something of importance. I don't know what it means, so if anybody could let me know what it is and how to fix it, i'd be very grateful.

Thanks in advance,

Blackjack
 

Answer:Single loud Beep

Does anything happen after the Beep? It could be that you have the CPU overheating alarm in the bios, set too low
 

7 more replies
Relevance 60.68%

HELP!

my laptop makes a loud continuous beep while booting. It does not occur every time i start the pc, but it happens most of the time. though it functions properly after it starts, the start-up can be quite irritating.
i checked pretty closely for any stuck keys.. cudn't find any. i'm wondering if it's heating up that causes it to shout out loud or some other problem hidden inside the case..(i guess thoshiba laptops heat up more than the others-from what i have noticed, but then i'm no expert.. ) before i get him to a repair center, just wanted to find out if there's anything I can do to stop it..

Also, i am due replacing the battery.. the laptop functions only when it is plugged to power. dunno if that makes any difference bbut just wanted to make a mention..

it's a thoshiba pc with 3gb ram and intel pentium dual cpu t3400 @ 2.16ghz.. whatever that means

thx!
 

Answer:loud beep while booting

11 more replies
Relevance 60.68%
Question: loud beep sound..

when i pressed the power button, i heard loud beep sound approximately 30 seconds, later it is disappeared and the window is automatically started.After window start, i can use it as usual. My computer is acer 4935 G series.. Please help me.. what is the problem for that ? OS is window 7 Ultimate 32 bit. please reply me ([email protected])

Answer:loud beep sound..

Do not post your email address in an open forum, you will get slammed with junk and no one will answer you that way. Use the edit feature to remove it please.This is a chart of the most common Beep codes for motherboards, look up your BIOS type and see what it says for you:http://www.5starsupport.com/info/be...Once you know what it is, post back for details on following up on the problem and fixing it.You have to be a little bit crazy to keep you from going insane.

2 more replies
Relevance 60.27%

Anyone have any experience with a continuous disabling/enabling of a USB device (in this case a printer) after installing on an X201 running Windows 7 Pro 64 bit?  Printer (older HP 2420) installs as expected in Win 7 and test page prints as desired.  Shortly thereafter the device seems to drop/readd continuously, and the only way to fix is to unplug the device. Any assistance?  Thanks.

More replies
Relevance 60.27%

switch the power on and nothing happens except for a continuous beeping. any ideas?
OPERATING SYSTEM: Windows 98 Second Edition (H3660) [WIN98SE]

MOTHERBOARD: RM Aopen MX36LE MicroATX VIA Apollo PLE133 Chipset [MX36LE]

CPU: Celeron 800MHz KNI (100MHz Front Side Bus)

RAM: 64MB (SDRAM) (upgraded to 256mb)

VIDEO: VGA Integrated Via VT8601 [_ATRI2D]
SOUND: Integrated AC97 Audio (AD1885 CODEC) [0AVIAC97]
 

Answer:(Solved) Continuous beep won't boot Award Bios

8 more replies
Relevance 60.27%

HI
Long time no see, friends.
My beloved I570 is acting up, probably some sort of Alzheimer or similar.
Here is what happened, will try to be short.
Initially I was using PCIE SATA card to attach 4 more HDDs to the system, then SATA card died (already second in this PC), so I decided to remove all extra HDDs sitting in the case.
Did all standard precautions, including grounding etc. In order to remove HDDs I had to clear MOBO of a lot of cables and remove GPU. Long story short, after I put everything back together and attempted to boot up, I got long continuous beep and WIN7 sliding bar freezes almost at the end, no further activity, just a long beep. BIOS was not accessible as well.
So, I removed GPU, pull out MOBO 24 pin PSU cable, removed CMOS battery, did multiple 30 sec press and hold power button thing, left everything dead completely for about 30 minutes - completely reset system clock and all BIOS settings to default. Also, swap RAM (I have 2 sticks in slots 3 and 4) places. Put everything back, fired up, went to BIOS and fixed everything, DONE, rebooted and everything went back to normal.
Multiple restarts were OK, did also a few cold reboots with some minutes apart - all seems to be normal. Turn it off for a day or so.
Now problem is back again, like nothing happened.
Please, help if someone actually can. I checked multiple thread here and all over the WEB. My keyboard is clean, RAM was resettled, all connectors are firmly attached. This doesn't make any sense.
... Read more

More replies
Relevance 60.27%

i allowed Windows Assist to make some changes and after that experienced following problems -  1. Display became black2. Continuous beep sound3. Keyboard is inactive Tried to resolve the problem by making some changes in the settings of "sticky keys". Has'nt helped.

More replies
Relevance 60.27%

Hi all, I have bought HP Pavilion G6 about 4 years back. Now while turned on the continuous beep sound is coming but after while the system will open. After turned on the cursor would not , if i press "ESC" key the cursor becomes active and again some error sound will come and it will not work properly. There is a lag while using the touch pad and also  If i delete the file it is not deleting. Please suggest if i can do anything for that problem before carrying to the service center.

More replies
Relevance 60.27%

Have been having boot up problems, going to safe mode to start, in the process I have to turn the power all the way off to get the computer to start, I was getting the usual outage noise when a computer is improperly turned off, now the noise will not stop and the computer will not boot at all.
 

Answer:XP making continuous loud whirling noise when starting system, no boot up

Sounds to me that maybe its a bios problem . When booting the default place that windows looks to get its startup info from is the HDD. If that was changed, say to cd drive then it would look there. No info there would mean its stuck in limbo. Try searching the site for bios or boot up problems. This situation is far from new and ,hopefully its not your machine, you will find the right solution for you.
 

1 more replies
Relevance 59.86%

Sometimes of late, my computer has been "stalling" while trying to switch between programs. It stalls and then there is a loud beep. Is an indication of a problem or is it an indication that I am over taxing the computer?

Answer:Computer Hanging And Loud Beep

Well...it's not normal, so I would consider it a distress signal .

Could be heat-related, could be memory...how often a day does this happen and exactly what are you doing when it happens?

How large is your C: partition, how much free space on same?

How much RAM installed in your system (Start/My Computer/Properties...second last line)?

System manufacturer and model? Laptop or desktop?

Louis

2 more replies
Relevance 59.86%

Hello all, 
I see that this has become a common issue, and one that I also experienced with my Dell XPS 13 2-in-1. My laptop would beep randomly (seemingly from somewhere in the keyboard)  from the first day I received it in the mail, and it eventually began beeping three to four times per day.
When I finally sent it to Dell for repair it had come to the point where the laptop was completely unusable and began emitting a horrible electronic noise that did not stop until the battery was empty. Dell replaced the motherboard and hard drive, this fixed the issue.
If you are having this loud beep problem my suggestion is to send your XPS 13 2-in-1 into Dell, and have them run diagnostics on the motherboard/hard drive. 

More replies
Relevance 59.86%

Needless to say but this sound is plain ridiculous. Who was the genius who came up with this idea? Seriously. I have the Y430 and recently installed Windows XP Pro SP3. I remember that disabling the PC speaker in Vista worked, but unfortunately that does not work with XP. With all the suggestions that have been mentioned, I have yet to find a way to be able to disable this power beep: There is no option in the Advanced BIOS menu. There is no PC speaker volume control. Disabling the 'Beep' option in the device manager does not work. I'm tempted to try the BIOS update even though it says it's for Windows Vista only just to see if I could get the BIOS option for this speaker. Would this be a wise choice? Better yet, would it even work?

Answer:LOUD and very annoying BEEP - Y430 XP SP3

hi, Go to panel de control, Sounds, You need to mute the option 'PC SPEAKER', it work with lastest driver in VISTA, and WIN 7. If mute the 'PC SPEAKER' does not work I will try to update the lastest driver available from the lenovo page. http://consumersupport.lenovo.com/en/DriversDownloads/drivers_list.aspx?CategoryID=11 Good Luck, The solution works with a lenovo Y430 the model that has DDR3, I know that you computer might differ, because there is basically two different y430. Remember to mute, for some reason regulate the sound will not work.

1 more replies
Relevance 59.86%

Greetings all, and happy 4th of July!

I recently helped my mother buy and put together her first computer (EMachine), but after turning it on, it made a LOUD beep. The beep apparently is coming from the tower, because it did it again after turning off the speakers, and restarting. I know that some computers beep once during their POST checks to tell you everything is OK, but this beep is LOUD, and I'm hoping someone here can tell me a way to disable, or at least make it a little quieter. It scares everyone out of their socks, the first time they hear it boot I've done a Google search to try to figure it out myself, but all I could find out is that Emachines are indeed notorious for loud POST checks. No one actually suggests a fix for the problem. I don't remember much about the computer except that it's a new Emachine running XP Home. If additional tech specs are needed, I can find out. Thanks.
 

Answer:Emachine makes loud beep!

I know exactly what you mean... and that beep irritates the bejebus out of me so I always unhook the case speaker from the motherboard or dont install it in the first place unless I have ( rare ) hardware or OS issue then I plug it back in.

as far as I know their is no way other than unplugging the case speaker from the mobo to stop the beep.... by opening the case on a new PC you may well invalidate any warranty tho.
 

4 more replies
Relevance 59.86%

I have a Dell Inspiron 6000 laptop with Windows XP Home Edtion Service Pack 3. It was working just fine until I started my laptop and I heard a loud beep while I in the desktop waiting for my laptop to finish loading. I decided to restart and then I got a BSOD while XP was loading. The message was:

STOP 0X0000007E (0XC0000005, 0X00000000, 0XBA4CAFDC, 0XBA4CACD8)

Restarting the laptop again lead me to the screen stating Windows did not start properly and gave me the list of options. I chose Last Known Good Configuration.

The BSOD has not appeared since but the laptop continues to beep loudly every time I start my laptop. I have not made any recent hardware changes, the last being upgrading the RAM over 9 months ago, nor have I recently installed/ uninstalled any software. I thought that the error may be due to inserting a USB hard drive and thumb drives but starting the laptop with no USB devices attached still caused my laptop to beep.

Any help would be greatly appreciated. Thanks!
 

Answer:Loud beep then BSOD XP Home Ed

6 more replies
Relevance 59.86%

Sat P300-17R: when my virusscanner (antivira) detects an virus or spyware it gives an very loud beep, and I mean very loud! In the program I can not change the warning options and shutting down my soundcard does not help either.

Can anybody help me getting rid of this nuisance

Message was edited by: Broi

Answer:Very loud beep on Satellite P300-17R

Try assigning WAV files to the "Default Beep" and "System Notification" events in Control Panel -> Sounds and Audio Devices -> Sounds

Windows may be defaulting to the PC Speaker for some sound events.

Also check the settings in antivira, perhaps you can change or assign a sound file to the virus alert event.

4 more replies
Relevance 59.86%

Hi everybody,I've got an Lenovo 3000 N500-46G, which does a loud beep when I plug in the A/C-adapter. There's no BIOS option for that, I already tried to deactivate the service (Beep) in the hardware manager. But this can't be a solution (OS-wise, installed Vista Home Premium 32-Bit), there are the same loud beeps when I press an not-used button in the BIOS (like # or +). I already got headache Hope there will be a solution...cheersMessage Edited by fromHeart on 12-13-2008 09:44 AM













Solved!

Go to Solution.

Answer:N500 46G loud beep when pluggin in a/c

Good question! I would like to know the same. The only 'solution' I found so far is to turn the volume down or off. But that is not a real solution of course.

9 more replies
Relevance 59.86%

Hi everyone. Ok, so after getting my new case, I swapped all my goodies into it today. I got a Thermaltake Tsunami case which I love. I didn't remove the memory or cpu from the board. After reassembling everything in the new case, everything powers up (no display on monitors) and I get this loud continuous beep. I can't seem to find a post code for what this would be. I tried reseating the video card and all the memory but no change. I need all your help on figuring this out. Oh, before that, I kept getting a CPU test fail message so I pulled the CPU and reseated it too. I also tried resetting CMOS. Thanks for any help!

My system:

ASUS P4P800-E Deluxe
P4 3.0ghz
1 gb Kingston HyperX 3200
EVGA Geforce 6800 video card
Western Digital 200gb HD
480 watt Demon power supply
Thermaltake Tsunami case
 

Answer:Constant loud beep on power up

I think that is a memory problem? I have gotten that before when i forgot to put the memory in. Maybe it went bad somehow. Try putting it in another slot, and make sure the video card 4 pin molex is connected.
 

3 more replies
Relevance 59.86%

Hi there,

I've started having problems with my fairly new PC (only a couple of months old)

Occasionally, and without warning, my computer starts making an extremely loud long beep noise at the same time as crashing. It does not sound like the internal speaker(although it could be), but it is definitely coming from inside the case. As soon as the sound starts, there is a crackling noise and the screen goes black. I have to switch off the PC quickly because the sound is very loud.

Now the first few times this happened, I looked inside the case and found that the CPU fan had been disconnected and wasn't spinning. I reconnected it and assumed the problem would go away, which it did for a while. A few days later though it did it again.

It's only happened maybe 5 or 6 times over about a month, but I'm afraid it'll happen again and I'll lose unsaved data.

Not sure of the exact Motherboard specifics, but I have an ASUS motherboard of some description, with an Intel core duo CPU 6600 @ 2.4 ghz and 2.39 ghz

Graphics card is NVIDIA Geforce 8800 GTX (I've been having slight graphics issues, may be related). I removed all other cards and the problem still happens.

Any help would be greatly appreciated.

Thanks in advance

Steve.
 

Answer:Very loud beep/whine before crash

16 more replies
Relevance 59.86%

I have a problem with my power-cord plug-in/out beep. ITS VERY LOUD and annoying and I cannot disable or adjust it to a reasonable volume. This problem is known for years but Acer wont come with a fix for this problem. Maybe someone can help me with this problem, I know for sure that this will be mine last hardware from Acer, WORST after sale and customer support ever.

Answer:powercord loud beep sound

Can you tell:notebook modelOS installed by the way, try this if available:right click the volume icon down in the task menu > then hit playback devices > then right click speakers (realtek high definition audio) > hit properties > hit the tab "levels" > there you should see a slider named " Pc Beeps" or "PC speakers" turn that down/mute 

5 more replies
Relevance 59.86%

Hi,when I start my Laptop I get an very loud beep after "ThinkVantage Active Protections sensor diagnostc start" is ready. After that, the Windows system is starting.Is it possible to deactivate this beep signal? I have cheked the whole bios an did not findy a check box for this beep.pls help





IBM ThinkPad Z61m

Answer:Z61m beep loud on start?

The Active Protection sensor is only tested by an extended power on self test(POST).  The extended POST also emits a beep when it finishes successfully.Enter BIOS Setup, select Startup, select Boot Mode and choose Quick instead of Diagnostics.  Your machine will boot faster now and not beep unless something is wrong. The beep volume can be adjusted with the volume control buttons too.





__________________________________________________I was previously employed by Lenovo but have no formal role on this forum.I am here on my own time because I like fooling with PCs, especially Lenovo ones. ALL my posts are purely my personal opinion.

2 more replies
Relevance 59.86%

Few months back my dell inspiron 3537 64-bit 6GB ram with i5 processor has fell down from table. It worked well even though there was a crack on the backside of the screen near right hinge.  But now from past one week it  giving trouble in many ways ! Whenever I try to start it it either starts to give continuous short beeps or goes into looping restart. I can hear the drive sound and see power led glowing but the screen doesnt display anything except for changing from dark black to light black. Hdd led also doesnt blink. Please help me configure the issue and solve it.

Answer:Inspiron 3537 gives continuous short beep and looping restart

How many beeps between pauses?
Can you get to the Dell diagnostics (F12 at powerup) -- press immediately after starting the system?

1 more replies
Relevance 59.86%

Hi
I am having inspiron 14r and I am facing some issue with it recently.
After starting my laptop, it works fine for 4-5 minute. After that continuous beep sound is coming.
It is very loud
Please help me.
Also, there is no problem with the screen or other software in the lappy. Only the continuous loud beep sound starts and after that laptop gets hanged.

More replies
Relevance 59.86%

Hello,

For the past two weeks my laptop has been beeping. It doesn't beep when I first turn the computer on. Once I'm to the desktop it starts to beep and it's VERY inconsistent. It may beep 5 every five minutes or every 20 minutes. Sometimes it beeps once and other times its beeped two or three times fast. And occasionally I get the BSOD saying something about "dumping my physical memory." On top of that when I load the computer I get an error saying that my Catalyst Control Centre is not working. I just assumed all these things were connected.

A few months ago my hard drive died so I installed a new one. I haven't had any issues until the issues I listed above, all of which start just a few weeks ago. Unfortunately my warranty has expired so Dell's support hasn't been much help.

So does this sound like the hard drive I installed is creating the issues? Any advice is very helpful!
 

Answer:Dell Studio 1536 with Vista 64 has a continuous beep and BSOD

Have you checked for crud in your keyboard... any cause for a sticking key, sticking space bar, etc.

Don't see how the hard drive could cause the problem.

Have you looked at all the Dell Beep Codes... They are posted elsewhere on this TechSpot forum... that could give you a starting point.
 

2 more replies
Relevance 59.86%

Hi

One of my pc's recently acted up. It was working fine for couple of years without problem and then I stopped using it for a few months; now when I go back to it, the motherboard just beeps continuously (long beep).

According to the manual, a continuous long beep might be due to bad ram, but when I took out both ram sticks, it had a different kind of continuous beep. I replaced the ram with a different stick and it made the continuous beep sound like the other ram

The motherboard is gigabyte GA-8I945PL-G, dual core cpu. Bios is award

When I had the hard drive plugged in, even tho it made the loud continuous beep, it booted to windows (win2k pro) ok except that the graphics looks as if the video driver has not yet been installed. I didnt want to potentially damage it so i turned off and I took out every component except for just the video card and ram. What should I do next? swap psu? I have an antec 550 true power.

Also, what should the beep sound like if i were to take out the video card?
Please help.

Thank you
 

Answer:Solved: system continuous long beep but boots to windows ok

ok, i figured it out! it's kind of a duh thing! The fan in the front of the case, instead of being connected to the connector on the mobo (system fan), was connected to the normal molex connector because it didnt have the right end. And in the BIOS, the setting was to monitor the system fan; since there's no fan connected there, it was beeping to alarm me about it; disabling that works hahahah
 

1 more replies
Relevance 59.86%

hello.. i'm new here... and i need some help... my computer is AMD Athlon 850Mhz... i'm using genious keyboard and a4tech mouse... 3 days ago, we decided to replace both since they are old enough to retire... so we bought a brand new generic keyboard and generic optical mouse, but after installing these devices during startup (counting and detecting devices) i'm hearing a continuous beep sound and it will stop when entering windows xp but i keyboard and mouse are not functional... please help!
 

More replies
Relevance 59.86%

I have a T5500, and anytime I stress the CPUs the system starts a continuous, constant beep noise.
The system still appears to run normally and the CPU temps are also under control, just the annoying sound.
I do not see a continuous sound anywhere in the manual so I don't know what this means.
This is an old machine and out of warranty so if I cannot find the problem, can I just turn off or disconnect the speaker making the noise?
Thanks.

Answer:[Solved] T5500 Workstation continuous beep with high CPU usage.

Solved, I feel like such an idiot. Someone helped me find the problem. I am powering the PC with a UPS unit right next to it and it clearly does not have the juice to power the T5500 anywhere close to full load.
So after days of troubleshooting I found it to be a simple ID10T error.
Thanks.

1 more replies