Computer Support Forum

Frequent system hangs, "atapi Event ID 11" in Event Viewer

Question: Frequent system hangs, "atapi Event ID 11" in Event Viewer

Hi, I recently made some upgrades to a (previously fine) PC - they were

- Installing 4GB extra RAM, of the same variety
- Reinstalling windows on a new SSD (a Samsung SSD 850 EVO 500GB)

I previously also upgraded to Windows 10, but a bunch of blue screens and other issues later I reinstalled 7. I'm still having problems though - the current symptoms are that every so often (1-3 times a day) the computer will hang for ~1-2 minutes on the 'starting windows' screen. When it finally loads, it will often hang for further extended periods before settling down. I checked in these event log and during these periods there will be many 'atapi' errors, with Event ID 11 "The driver detected a controller error on \Device\Ide\IdePort0." (I have attached a screenshot).

There will sometimes be other errors, usually relating to the timeout of certain things, but the previously mentioned error is by far the most prolific. On rare occasions there have been more serious errors - never blue screens since going back to windows 7, but once I booted to a black screen with just a mouse (was able to shut down via task manager then following a restart seemed ok).

Through some investigation, it does seem to be that the root cause of the problem is the SSD; I identified this a while ago and have tried various fixes, including:

Ensuring my Motherboard (a M4A78LT-M) SATA ports are configured in AHCI mode (they were previously IDE). This also led me to completely re-installing windows in an effort to make sure the correct drivers were installed (though more on those drivers in a second).
Updating my motherboard's BIOS.
Running MemTest to check my RAM wasn't causing the problem.
Changing the SATA cable and port of my SSD.
Updating various drivers from ASUSTeK Computer Inc. -Support- Drivers and Download M4A78LT-M for my motherboard, including the chipset. I saw another driver for "AMD AHCI Compatible RAID Controller Driver V3.1.1540.127", but when I try and updating this windows just says that the most up to date driver is already installed.
I've also tried running various checks for disk errors, including the Windows built-in drive checker and HD tune pro.
I just tried unplugging my DVD drive as well, which is the only other thing connected to the SATA ports.
On a side note, I do not have the 6Gb/s SATA 3 ports, only 3Gb/s SATA 2, though I don't see why this should be a problem.
I've of course looked online and have found many people with similar issues, but often they seem unresolved, or their fixes unfortunately don't work for me. Any help would be massively appreciated as this has been plaguing me for weeks!

More replies
Relevance 100%
Preferred Solution: Frequent system hangs, "atapi Event ID 11" in Event Viewer

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

Relevance 104.11%

since about 3 months ago, my computer has been experiencing multiple BSOD's per day. upon looking in the event viewer, ever single time and event with something to do with a "VSS service" is the last thing before the crash. i find this strange, as looking into this, vss is a backup program for xp and server 2000. i have no idea why this is on my system, what it does, or why i need it. after trying to use some debugging tools, it seems that i cannot access the .dmp files on my own computer, logged in as an administrator, with full privileges, with all file security options in my anti-virus off. my system is a x32 vista business. the crahses occur almost at random, doing anything from playing a game, using Firefox, typing a notepad file, or just leaving the thing on and not doing anything for more than 10 minutes. the system will still crash at the log in screen, leaving me to believe that this is not an overheating issue. i have tried to disable all programs with mscofig, but i still get a crash. i have even had crashes in sleep mode, as well as in the process of a normal shutdown. i have no new updates in windows update, and have installed all of the new drivers for every device i can find them for. any and all help would greatly be appreciated.
 

Answer:frequent BSODs with event viewer pointing towards "VSS service"

Hi this is about vss and what you can do with it http://www.mydigitallife.info/2007/...tem-restore-disk-space-limit-in-explorer-gui/
 

2 more replies
Relevance 98.31%

Ok, so im new here so hey everybody..

to the point: my laptop is "stuttering"/lagging/skipping.
whatever you wanna call it its doing it.
my video/music/and cursor skip every second for a splt second it starts on start-up and dont stop til i turn my laptop off. it happens in a pattern its not random, ive done checked my drivers, spyware, and m RAM is good.. so can someone please help me? ***could it be because my battery wont hold a charger? so it has to be hooked up to the charger at ALL times or it dies Example: is the charger not got the "juice" to run the laptop by itself so it studders/skips..*** i dont know if this has anything to do with my problem but i ran "event viewer" and found this : The following boot-start or system-start driver(s) failed to load:
Cdrom
Imapi
redbook

PLEASE HELP




OS Version: Microsoft Windows XP Home Edition, Service Pack 3, 32 bit
Processor: Genuine Intel(R) CPU T2250 @ 1.73GHz, x86 Family 6 Model 14 Stepping 8
Processor Count: 2
RAM: 502 Mb
Graphics Card: Mobile Intel(R) 945GM Express Chipset Family, 224 Mb
Hard Drives: C: Total - 39723 MB, Free - 23484 MB; D: Total - 12684 MB, Free - 3633 MB;
Motherboard: Dell Inc., 0FF049, , .HWPLLB1.CN1296167S5169.
Antivirus: McAfee VirusScan, Updated: Yes, On-Demand Scanner: Disable
 

Answer:Solved: Whole computer "studders"/"skips"/"lags" .. have event viewer report (PLEASE

6 more replies
Relevance 97.44%

Ok, so im new here so hey everybody..

to the point: my laptop is "stuttering"/lagging/skipping.
whatever you wanna call it its doing it.
my video/music/and cursor skip every second for a splt second it starts on start-up and dont stop til i turn my laptop off. it happens in a pattern its not random, ive done checked my drivers, spyware, and m RAM is good.. so can someone please help me? ***could it be because my battery wont hold a charger? so it has to be hooked up to the charger at ALL times or it dies Example: is the charger not got the "juice" to run the laptop by itself so it studders/skips..*** i dont know if this has anything to do with my problem but i ran "event viewer" and found this : The following boot-start or system-start driver(s) failed to load:
Cdrom
Imapi
redbook

PLEASE HELP
 

Answer:Whole computer "studders"/"skips"/"lags" .. have event viewer report (PLEASE HELP)

**(DONT KNOW IF THIS WILL HELP..)***

Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows XP Home Edition, Service Pack 3, 32 bit
Processor: Genuine Intel(R) CPU T2250 @ 1.73GHz, x86 Family 6 Model 14 Stepping 8
Processor Count: 2
RAM: 502 Mb
Graphics Card: Mobile Intel(R) 945GM Express Chipset Family, 224 Mb
Hard Drives: C: Total - 39723 MB, Free - 23484 MB; D: Total - 12684 MB, Free - 3633 MB;
 

2 more replies
Relevance 94.83%

Hello
I am new to Microsoft Message Analyzer and just downloaded version 1.4 and installed on my Windows 10 laptop
I saved my Windows System Event log as an .evtx file to have some data to start looking at. I note the column entitled 'summary' appears to show the body of the event message. However I see many rows which state "unable to retrieve the event description"
in this column, what do I need to do to fix this issues please? could it of been the way that I saved the .evtx file in the first instance (I accepted the defaults) or do I need to install some additional files/components so the messages are displayed
correctly?

Thanks all
Ernest

More replies
Relevance 89.9%

My sys: Win7 64 bit Prem. Home Ed., AMD Phenom II X6, ASUS M4A88T-M socket AM3 mobo, 2X 4GB Corsair memory, 2TB Seagate Barracuda Green HDD, built Aug. 2012 by little ol' me.
My problem: Screen will freeze right after logging into user account, it will also freeze when we are in the middle of something (online or off line). Grrrr!. This happens more frequently to my husband (non-administrator) then to me (administrator). We try to go through normal shut down procedure and wind up having to force shut down. Sometimes we even have to purposefully crash it (unplug the tower).
When I check the Event Viewer I see over 3,000 events since Aug. 2012. Event ID 10 seems to proceed each instance of freeze. This is just one of about 20 different errors and warnings I'm finding in my Event Viewer.
Someone said to boot up in Safe Mode, find the "c:\windows\system32\wbem\repository" folder and delete it contents, then reboot normally twice. But he was talking about Vista.
My husband is upset , since we've spent close to a grand on this machine. I am confused to say the least and will appreciate any constructive help you can give.
Thanks!

Answer:New system, no BSOD, but frequent "___is not responding' Event ID 10.

Also, (in case this is important) I have Avast!, Spybot, AdAware & ccleaner installede on my system.

1 more replies
Relevance 86.42%

Below are my errors, keep in mind the MSI Gaming App (see final error) always does that, seems they broke it someway for anniversary edition and never fixed it. Any ideas what I should do to get rid of these?


Code:
The Open Procedure for service "BITS" in DLL "C:\Windows\System32\bitsperf.dll" failed. Performance data for this service will not be available. The first four bytes (DWORD) of the Data section contains the error code.

The Open Procedure for service "ESENT" in DLL "C:\Windows\system32\esentprf.dll" failed. Performance data for this service will not be available. The first four bytes (DWORD) of the Data section contains the error code.

The Open Procedure for service "Lsa" in DLL "C:\Windows\System32\Secur32.dll" failed. Performance data for this service will not be available. The first four bytes (DWORD) of the Data section contains the error code.

The Open Procedure for service "MSDTC" in DLL "C:\Windows\system32\msdtcuiu.DLL" failed. Performance data for this service will not be available. The first four bytes (DWORD) of the Data section contains the error code.

Unable to open the Server service performance object. The first four bytes (DWORD) of the Data section contains the status code.

Windows cannot load the extensible counter DLL rdyboost. The first four bytes (DWORD) of the Data section contains the Windows error code.

The Open Procedure for service &quo... Read more

Answer:Event Viewer Error The Open Procedure for service "ESENT" in DLL

Please note: This section is exclusively for BSOD errors not System event viewer errors.

1 more replies
Relevance 86.42%

Below are my errors, keep in mind the MSI Gaming App (see final error) always does that, seems they broke it someway for anniversary edition and never fixed it. Any ideas what I should do to get rid of these?


Code:
The Open Procedure for service "BITS" in DLL "C:\Windows\System32\bitsperf.dll" failed. Performance data for this service will not be available. The first four bytes (DWORD) of the Data section contains the error code.

The Open Procedure for service "ESENT" in DLL "C:\Windows\system32\esentprf.dll" failed. Performance data for this service will not be available. The first four bytes (DWORD) of the Data section contains the error code.

The Open Procedure for service "Lsa" in DLL "C:\Windows\System32\Secur32.dll" failed. Performance data for this service will not be available. The first four bytes (DWORD) of the Data section contains the error code.

The Open Procedure for service "MSDTC" in DLL "C:\Windows\system32\msdtcuiu.DLL" failed. Performance data for this service will not be available. The first four bytes (DWORD) of the Data section contains the error code.

Unable to open the Server service performance object. The first four bytes (DWORD) of the Data section contains the status code.

Windows cannot load the extensible counter DLL rdyboost. The first four bytes (DWORD) of the Data section contains the Windows error code.

The Open Procedure for service &quo... Read more

Answer:Event Viewer Error The Open Procedure for service "ESENT" in DLL

I figured this out, nothing was wrong with Windows 10, running sfc /scannow returned no errors.

I ended up removing MSI Gaming App because they have yet to correct whatever is wrong, this got rid of that event for me.

I opened CCleaner and under Startup I figured some program must be causing these errors since I'd been clearing the event logs using Clear_Event_Viewer_Logs and they only occurred at startup. I discovered MSI Gaming App didn't remove it's startup entry neither did CoreTemp remove its scheduled startup (I took it off because I'm using Secure Boot and it isn't yet licensed to work with it.)

After deleting those I have no more errors. None. Really annoying!

1 more replies
Relevance 86.13%

Hi All,

I've had an issue with Event viewer unable to start due to "endpoint mapper database entry could not be created" Error 1899. I have done a SFC and have had some but not all issues fixed, I have a log of the result and maybe could post if needed. I've also done a system restore to a previous working config but no luck, the problem still persists. Has anyone had experience with this issue and know a fix for it?

Regards
Hiconic

Answer:cannot start event viewer "Error code 1899"

It's no wonder people slag off Microsoft for the lack of support. This issue has effectively stopped me from doing any back up on my PC as without the Event logging service or Event viewer service running the Back up cannot be set as it's dependent on these services which are hog tied by this endpoint mapper issue! Another Windows endless catch 22 loop!!

I can't believe no one has anything to offer on this issue! I've seen this issue raised on several forums but as yet no one seems to have the solution, which begs the question where are all the experts out there specializing in Windows 7? Suddenly, nothing happened!!

Hiconic

4 more replies
Relevance 86.13%

My Windows 7 configuration is relatively bullet proof (ha ha, nervous laughter).

My OS and programs are on C, which I image using RDriveImage every month after Patch Tuesday.

My data is on software-mirrored D/F drives.

So as long as I don't have a catastrophic event affecting my computer, a routine "drive failure" should be recoverable, with the worst-case being I'd be out a month of updates, but with a good recent image of the OS drive.

Anyway, I was recently looking at my event viewer and I have "Disk errors" that occur whenever I run a full image of C.

The complete error text is:






Quote:
Log Name: System
Source: Disk
Date: 7/13/2012 3:38:44 PM
Event ID: 11
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: xxxxxx
Description:
The driver detected a controller error on \Device\Harddisk3\DR3.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Disk" />
<EventID Qualifiers="49156">11</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2012-07-13T19:38:44.199218700Z" />
<EventRecordID>136049</EventRecordID>
<Channel>System</Channel>
<Computer>xxxxx</Computer>
<Securi... Read more

Answer:"Disk error" invisible except to event viewer, when imaging hard drive

Try going into your BIOS to see what it has to say about the drive. Some BIOS's can read the drive's SMART status and can run tests on it. You could also download the disk manufacturer's drive diagnostics to check it out. Or see what Seatools (from Seagate) has to say about it:

SeaTools | Seagate

9 more replies
Relevance 85.84%

Good evening. I've got something weird going on I'd like to ask for help with. Every time I close the Event Viewer or Task Scheduler I get a new "Administrative Tools" folder on the desktop. As far as I know, no other programs cause it, at least none of the ones I tested. I'm not exactly sure when it started but I know it hasn't always done it. I've already got Administrative Tools folders in my Start Menu. Anyone know what could be causing it? Thanks.

Answer:"Administrative Tools" folder created on desktop every time I close Event Viewer

Walt
Sounds like a change in your settings. To be sure
Run a full anti virus scan
Download and run a full scan with Malwarebytes to be sure we are not talkling about a virus
If all are negative, go back with System Restore to a week before the problem began.
System Restore - How to

7 more replies
Relevance 85.84%

I'm running Win XP Home - SP1. I just learned about the Event Viewer (Control Panel/Admin Tools) and the Security section shows a number of Anonymous Logons. It also shows Guest Logons, etc, along with "Failed Audits", indicating wrong passwords. Every other "Failed Audit" shows "MICROSOFT_AUTHENTICATION_PACKAGE_V1_0", with the following one showing my name.

I do have a home network with a wireless router. Only the laptop wireless card and PC network card MAC addresses are cleared for access. My closest neighbor is over 800 feet away so I'm confident that I'm not being accessed locally.

Any idea what this is all about?

Thanks.
 

More replies
Relevance 85.84%

WinXP Media Center Edition SP3 - there are numerous "warnings" in the Event Viewer in the 'System' section. Each time the warning shows up (about every 2-4 days), there will be at least 5-6 in a row, sometimes as many as 15 all in group. Here's the message (a screen shot is attached below also):




Event Viewer said:



Event Type: Warning
Event Source: Disk
Event Category: None
Event ID: 51
Date: 2/6/2011
Time: 8:14:29 PM
User: N/A
Computer: OWNER-EF6521BE4
Description:
An error was detected on device \Device\Harddisk0\D during a
paging operation.Click to expand...

The owner of the PC is convinced the new hard drive I installed about a year ago is failing because he'd get occasional BSOD crashes, but I ran 2 different diagnostics on the drive, and both passed 100% (one was the Seagate 'Seatools' bootable diagnostic; it's a Seagate 320gb SATA drive). The system passed an extended RAM diagnostic (I knew the RAM was OK, but I ran the test just to be thorough). I'm researching the message right now, but haven't found much.... any thoughts?

Thanks!

(I've been using the PC for about 6 hours now w/o any problems, but then again, the warnings don't necessarily show up every day; sometimes there's 4-5 days with no warnings)
 

Answer:Numerous "warnings" in Event Viewer (WinXP)

Upon looking at the Event Viewer messages a bit closer, I found that there's a few of these identical warnings that refer to "\Device\Harddisk1\D" but the vast majority refer to HD0\D. There is only one hard drive in the PC.....
:confused

EDIT - a bit more digging, and I discovered that the "iPod Service has entered the running state" occurs about 40sec before a string of the warnings starts; the iPod service is not listed right before the warnings every time, but it is on all but 2 out of a total of 12 or 13 'runs' of the paging warnings.... a connection between the iPod and the paging problems?
 

3 more replies
Relevance 85.84%

Whenever I launch Event Viewer, I get this message. Ditto when I try launching Computer Management. I sometimes get a message about Adding a snap-in to console. But it never works. I ran SFC SCANNOW and it fix some stuff requiring a restart and is running clean now. No improvement.

I tried going back to an image from several weeks ago. Event Viewer worked but when I ran SFC SCANNOW and restarted, it stopped working again. If I run mmc.exe, I get a single folder Console Root. Trying to launch Event Viewer from the File menu crashes it. Running services the same way works. Running Component Management crashes.

Any ideas?

Thanks

Answer:Windows 7 x64 "Event Viewer has stopped working"

Check your system for BUGS. It is infected. That or the hard drive is corrupted and starting to fail.

These things don't Just Happen. Windows 7 is a very good operating system and does not have these problems unless something causes them.

3 more replies
Relevance 85.84%

1- this is my result in event viewer
http://img96.imageshack.us/img96/3197/26608902.png
and all i can see is " warning " and " error "
should i be worried ? and how can i solve the problems ?

2- i just changed my theme ... and the computer makes sound when i enter or exit a folder ... basically when i do anything ... how to mute the theme's sound ?

thanks : )

Answer:My result in the " event viewer " ... and theme problem

I can't help you with #1 but I'm sure someone here can certainly do so.

As to #2, go to your "personalize" options by right clicking on the desktop, select "Personalize" then select "Sounds" at the bottom of the Personalization Options window.
That will bring up the dialog pictured below. Your scheme (in the red box) will be different than mine. Just go to the blue box and change your sounds to your heart's content.

Note: the red and blue boxes are only for clarification - you will not see them.

9 more replies
Relevance 85.84%

Hello, I guess this isn't a huge issue since its more of an annoyance than anything. I uninstalled Internet Explorer and configured my Indexing Options so it wouldn't include the location used for IE history (I thought?). But this error pops up from time to time in the Event Viewer. I have searched so many places for clues but came up with nothing so I turned here. Not sure of the easiest format to display the errors and settings so here is a compiled image of the Event Viewer and Indexing Options.

http://i50.tinypic.com/w7kdg5.jpg

Correct me if I'm wrong but I understand that the Gatherer can't find the file/location because it doesn't exist?

I tried searching the internet for "S-1-5-21-3684526760-1838744142-3877755193-1001" but no results came up. But after searching my computer I found a "S-1-5-21-3684526760-1838744142-3877755193-1001_UserData.bin" file in the C:\Windows\System32\wdi\{86432a0b-3c7d-4ddf-a89c-172faa90485d} directory. Not sure what this means although I'm not going to try deleting it.

Is this something that just happens if you uninstall Internet Explorer or could it have been caused when I used CCleaner and it was still set to remove IE data even though it was uninstalled.

Again, this isn't a critical thing so if no solution can be found no worries. Just thought I'd ask, thanks!

Answer:Event Viewer Search Error "iehistory://"

Hello !!

Since Internet Explorer's rendering engine is also used throughout Windows and with third-party applications as an embeddable component, it won't completely uninstall—only the executable is actually removed. So even if you move Internet Explorer the traces would be still there.

Hope this helps,
Captain

2 more replies
Relevance 85.84%

Hello everyone and thank you so much for reading and helping me.
Let me first explain that I am running Windows Vista Pro. For the past few days, my computer has been freezing up as I have been browsing the web. Ctrl+Atl+Del does nothing, I wait to see if Firefox will respond to no avail. I am forced to do a hard shut-down. When I restart, the computer works well for a few hours, even a day or so. Then the freezing repeats.
My computer is up to date with all updates from Microsoft, the Microsoft Firewall is turned on and I have Symantec Anti-Virus up to date and running. (Actually I'm pretty compulsive with updating.)
So I decided to look at my event viewer to see if I could find out what was wrong. BINGO. Every time my computer has frozen up in the past few days, an event is logged as the following:
"An anonymous session connected from xxx.xxx.xxx.xx has attempted to open an LSA policy handle on this machine. The attempt was rejected with STATUS_ACCESS_DENIED to prevent leaking security sensitive information to the anonymous caller.
The application that made this attempt needs to be fixed. Please contact the application vendor. As a temporary workaround, this security measure can be disabled by setting the \HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contr ol\Lsa\TurnOffAnonymousBlock DWORD value to 1.
This message will be logged at most once a day."
I intentionally masked the IP address on this post. Each time the event is reported, the IP i... Read more

Answer:Question about "Error" found on Event Viewer

Hello and welcome to TheWindowsClub forum
It seems your computer is under attack.
You should prevent access to TCP 445 port by blocking it through Vista Firewall, or do use this temporary fix Security Research & Defense : Update on the SMB vulnerability situation
Please, tell me is your system up to date?

9 more replies
Relevance 85.84%

I have had recurring "Errors" in my Event Viewer files that reference "Application hang" and Category 101/Event 1002 OR Catergory (none)/ Event 1001. Can some one enlighten me as to what may be the cause of this problem. Thanks. {redoak}
 

Answer:Solved: Recurring "Error" in Event Viewer

7 more replies
Relevance 85.55%

Event Log Explorer
A tool to help Manage, Analyze and Report Windows Event Logs
For Windows NT/2000/XP/2003 operating systems​
This is a simple, "starter" guide to help use this tool. (Note this tool will only work on Windows NT/2000/XP/2003. It will not work with Windows Vista.) Download and run Event Log Explorer.

One time initialization

Click Tree->Show Tree
Click File->New Workspace
Click File->Save Workspace As (and save your workspace file anywhere you choose)
Example: To Filter / View / Export Recent Error and Warning Log Events

Open an Event Log
>> (e.g Typically, you only need look at the System Log (for System event records) and the Application Log (for Application related events)
Filter the events you want to see (for this example we filter to only see Non-Information events that occured in the last 7 days)
>> Click View->Filter.
>> Uncheck Information. Towards the bottom of the filter window, look for ?Display event for the last? enter 7 days. Click OK
Click File->Export Log to save a copy of the events for later viewing or sending to others
>> Check: Text file, All events, Event Description
>> Uncheck Export Event Data
>> Check Close dialog when done
Click Export and save as a txt file on your Desktop
Help Troubleshooting an Event

Double click an event to see the "Event Description" (which provides more detail about the event)
Click Event ID Database button for an web page a... Read more

Answer:"Event Log Explorer" tool helps manage/analyze/report on your Windows Event Logs

I use the subscription to EventID.net. It has been greatly helpful. I don't have this analyser but am a big believer in using the Event Viewer. I'll add a description I have written up which will help in determining the Events: This may be useful in addition to the Event Analyzer.

One thing I have not been able to do is keep the filters set with the software in the OS.

Find the Error(s)in the Event Viewer that correspond to the crash/freeze/error message/blue screen, etc.:

Description of the Event Viewer:




Unfortunately, many Windows XP users aren't aware of the Event Viewer, what it is, where it is, how it can help with a problem:
The Event Viewer has logs for everything that happens on the computer. There are three sets of logs: System, Applications and Security. By opening the first two to display the Events, you can look for Errors that correspond to the time of the problem- in your case, the crash.

There are three types of Events in the System and Apps logs:
1. Information (white circle w/blue i): this is just basic documentation of the normal working of the System or Apps.
2. Warnings (yellow triangle w/black exclamation mark) noting some problem at that moment. Warnings usually resolve on their own. If they do not, they become>>>
3. Errors (red circle w/white X- they document something that didn't work or isn't happening as it should. Each Errors has three parts: an ID#, a Source and a Description. By doing a right clic... Read more

1 more replies
Relevance 84.97%

Hi folks,

Has anyone else noticed that their event viewer to be far more busy than in Windows 8?

Got all sorts of strange errors in mine.

Not sure whether it's drivers, app compatibility .... or what.

Like this for instance....

Windows detected your registry file is still in use by other applications or services. The file will be unloaded now. The applications or services that hold your registry file may not function properly afterwards.

DETAIL -
50 user registry handles leaked from \Registry\User\S-1-5-21-2217591357-3541557252-3149719819-1001:
Process 680 (\Device\HarddiskVolume1\Windows\System32\lsass.ex e) has opened key \REGISTRY\USER\S-1-5-21-2217591357-3541557252-3149719819-1001
Process 680 (\Device\HarddiskVolume1\Windows\System32\lsass.ex e) has opened key \REGISTRY\USER\S-1-5-21-2217591357-3541557252-3149719819-1001
Process 680 (\Device\HarddiskVolume1\Windows\System32\lsass.ex e) has opened key \REGISTRY\USER\S-1-5-21-2217591357-3541557252-3149719819-1001
Process 680 (\Device\HarddiskVolume1\Windows\System32\lsass.ex e) has opened key \REGISTRY\USER\S-1-5-21-2217591357-3541557252-3149719819-1001
Process 992 (\Device\HarddiskVolume1\Windows\System32\svchost. exe) has opened key \REGISTRY\USER\S-1-5-21-2217591357-3541557252-3149719819-1001
Process 992 (\Device\HarddiskVolume1\Windows\System32\svchost. exe) has opened key \REGISTRY\USER\S-1-5-21-2217591357-3541557252-3149719819-1001
Process 992 (\Device\HarddiskVolume1\Windows\System32\svchost. exe) has open... Read more

Answer:Win 8 Event Viewer - You finding yours to be "busier"?

Something is opening registry handles to your user's registry or files in your profile and isn't letting go. It's doing so as part of a svchost, which means it's probably a task running in task scheduler. Have you installed any software that would have added any scheduled tasks?

9 more replies
Relevance 84.97%

This could also apply to XP and Vista, as well as Windows 7.
See thumbnail for 1 day's Statistics about Event Viewer from my W7 laptop.

To check your Event Viewer stats, in W7 go to:
? Click on the "Orb",
? In the Search box, type in eventvwr and press Enter.
? Double click on Windows Logs, to see itemised stats.
? Double click on each of the itemised stats to see individual occurences.

There will probably be 1000's of events listed in "Security", for example.

Optionally, you may scroll down through the lists of events in each heading to check out problems the Event Viewer may have found. This may help you in Troubleshooting problems.

You have the option of "Save and clear a log", or clearing the log without saving. (see additional thumbnail)

After you become confident in how your PC is running, you may simply clear the log, without saving the log.

Every so often it is worthwhile to review all listed events in each category, then clear them, just to confirm your PC is running OK.

It will also clear some Hard drive space by running Event Viewer regularly and clearing events listed.

Maybe you should "thumbnail" your stats in a reply here, for others to see how the events accumulate.

Bazza
 

Answer:When was the last time you cleared out "Event Viewer" in W7?

Good tip, Bazza - would never have thought of even doing that, much less knowing how. Thx! :major
 

12 more replies
Relevance 84.97%

With a clean install of Windows 8 I noticed a few strange issues. One being an empty folder appearing on the desktop for no reason, could delete it but then it would later come back. Right click on it and it has no options other than cut or delete.

Been with Win 8 for just over a day now, after severe grief with two installs going bad. (Upgrade doesn't work at all, 2nd I should have run Windows update before installing newer nvidia drivers).... I am left with an OS in reasonable working order.

Sometimes apps are not launching when I click on them and event viewer is being hammered.

There are lots of mentions or my Cyborg RAT 7 drivers in event viewer (Saitek errors).

What are people doing with regards to intel chipset drivers, the intel engine management drivers etc? Are you letting Windows 8 obtain them or are you getting them from Intel direct?

But look at this....

taskhostex (1768) An attempt to open the file "C:\Users\Damien\AppData\Local\Microsoft\Windows\W ebCache\WebCacheV01.dat" for read only access failed with system error 32 (0x00000020): "The process cannot access the file because it is being used by another process. ". The open file operation will fail with error -1032 (0xfffffbf8).

Or how about some of this....

Windows detected your registry file is still in use by other applications or services. The file will be unloaded now. The applications or services that hold your registry file may not function properly afterwards.

DETAIL -... Read more

More replies
Relevance 84.97%

I am using windows 7 x64 RC, My event viewer is filled with "Known folders" errors like this:Error 0x80070005 occurred while creating known folder {3eb685db-65f9-4cf6-a03a-e3ef65729f3d} with path 'C:\Windows\system32\config\systemprofile\AppData\Roaming'.Any ideas? Never seen this before.This is my second time installing windows 7 Rc. I installed it yesterday, then mysteriously got a BSOD 0x0000007E (no error msg) today.

Answer: "Known folders" errors in event viewer

The 0x07E error is usually the controller. Folder access problems also indicate some disk corruption problem.Rating posts helps other users
Mark L. Ferguson MS-MVP

64 more replies
Relevance 84.97%

I'm running WinNT 4.0 Server (SP5).
I noticed in the Event Viewer the message "The device \Device\Harddisk1\Partition1 has a bad block". The Event ID is 7 and the source is Disk.
I understand that part of the hard drive may be unuseable (I couldn't find much documentation on this error), although the server seems to be functioning fine (so far...).
What should I do, troubleshooting wise, as a result of this error? Also, any specific information on Bad Block errors would be greatly appreciated!

------------------
Howard Feldsott
 

Answer:"BAD BLOCK" error in Event Viewer - NT4

Well, for the NT part, you should really be in the NT forum.

Since you have a hardware question though, lets answer that first.

What brand hard drive is it? Most companies have utilities that you can run on the drive to test it.

------------------
Get free stuff and help out a poor computer tech

7/9 added two pay to listen to music sites

I've gotten 5 $18 amazon.com GCs in 4 weeks listening to music! http://www.rkfdcore.com/ebaypics/referrals.htm
 

3 more replies
Relevance 83.52%

Hi,

In every 3d game I play the game will freeze( sometimes seconds sometimes up to a minute) or freeze and lockup the computer. I checked the event viewer and it shows I am getting an nv error. Does anybody have any idea how to correct this? I've tried updating drivers,changing out the sound card,and moving pci cards around so my geforce ti500 card is on its on irq.
It has been a little more stable since I've done this but I've had this problem for over a year. I'm using xp. I'd apprewciate any help you guys can give me.

Thanks,
Dennis
 

More replies
Relevance 83.52%

I updated my ATI video card drivers from the factory installed drivers to the Catalyst 5.11s today after installing Microsoft .NET Framework 1.1 first.

After installing the new ATI drivers along with the Catalyst Control Centre as per the instructions on ATI's site, I noticed something in Event Viewer. In addition to the normal Application, Security, and System folders, a new one appears there called "ACEEventLog".

At the time that folder appeared, I noticed an Information event under "Application" that had to do with the creation of that new folder. In it, it mentions that it has to do with CLI.exe, which of course is a component of Catalyst Control Centre.

Is it safe to just ignore that new folder called ACEEventLog? I'm not sure why it is there, but I'm sure it appeared with the new ATI drivers because I check my Event Viewer on a daily basis.

I've attached some screenshots to explain what I'm talking about.
 

Answer:New "Event Viewer" Folder

Now that I have shut the computer off and turned it back on later, events were added to that new folder.

I've attached 2 more pics- one at 6:51pm that occurred when I logged off the computer, and the one from 7:10pm occurred when I turned it back on later.

Do these things mean anything? Are they harmless if I don't do anything about them?

Rollin' Rog, Cookiegal... someone help me please.

It sounds like this thread over here, but I'm not sure what to do:

http://www.developersdex.com/asp/message.asp?p=2911&r=4585665
 

1 more replies
Relevance 82.36%

System event not recording anything. It is empty, says "date is invalid(13)".

I have some flaky things going on like unexplained CPU spikes causing slowdowns and mouse drag. Also have video problems screen going blank then recovery.

I have reloaded video drivers to no avail. No system lockups or BSODs. I need to see system event log to debug. Other event logs OK. I am proficient on PC and have searched for event log problem. The Event Log service is running. Thanks.

hp pavilion dv9000
OS Name Microsoft® Windows Vista™ Home Premium
Version 6.0.6001 Service Pack 1 Build 6001
Processor Intel(R) Core(TM)2 Duo CPU T7100 @ 1.80GHz, 1801 Mhz, 2 Core(s), 2 Logical Processor(s)
BIOS Version/Date Hewlett-Packard F.23, 10/3/2007
SMBIOS Version 2.4
Installed Physical Memory (RAM) 2.00 GB
Adapter Type GeForce 8400M GS, NVIDIA compatible
Adapter Description NVIDIA GeForce 8400M GS
Adapter RAM 128.00 MB (134,217,728 bytes)
 

Answer:Solved: Vista, Event Viewer - system event log not recording

Did you check the - %SystemRoot%\System32\Winevt\Logs\System.evtx file? It may be corrupted and you may want to rename it to .old and let it recreate itself.
 

2 more replies
Relevance 82.36%

MY COMPUTER:
=============
OS: Win XP Corp SP2
MOBO: A7N8X-E Deluxe
CPU: AMD AthlonXP-M 2000 @ 2300GHz
HDD: Seagate ST3320620AS
Maxtor 6 Y160M0 (both SATA drives)
RAM: 2x 256 512MB pc3200 Crucial Value Select
GFX: ATI Radeon 9800pro
PSU: Antec 350? (the one that comes with Antec Sonata case) (broke)
Now I use a 400W no brand i bought for £15
BACKGROUND: (MAY OR MAY NOT BE RELEVANT)
============
My computer was running great until a few months ago when it crashed while I was playing HALO online. The computer turned off but the green light on front of case was still on. When i tried to reset it, nothing would come up on the monitor and the monitors light remained orange (standby). I knew the computer wasn’t booting up because it would have spoke to me as the a7n8x-e does. The fans and LED on the motherboard would turn on though and i could hear the HDD spin up.
Anyway I tried another socket A processor but it didn’t fix it. Then eventually I tried another PSU and that fixed it. My computer was working properly again.
THE PROBLEM:
============
When I tried to play HALO again on my computer I noticed that the originally smooth performance was now terrible. The game seemed to (and continues to ) freeze for a second every few seconds. When this occurs I can hear a click from the HDD and the screen and game freezes for a second. I tried to continue to play under these conditions the computer grinded to a halt and crashed.
When I checked the event log their are multiple event ... Read more

More replies
Relevance 81.2%

hi guys,

i am getting atapi errors in event viewer, the other day my monitor would not come out of power save mode. i have tester bother my hard drives and they pass. i have also checked my cables and they are fitted ok. i have never had this before and do not know what to do.

any help please?

Answer:Atapi errors in event viewer help plz

Hello Mark,

If you have an Intel chipset I solved my ATAPI errors promblem by installing the SATA AHCI drivers included in the Intel ""RST and AHCI Driver and GUI" file package. It can be found by a search here: Intel Download Center . The SATA AHCI driver is located in the \Drivers\f6flpy-x64 or \f6flpy-x86 folders . Use device manager to update. After updating restart computer. When restarted Windows will reinstall drivers for the harddrive(s). Another restart is required.

I have not had an error since I installed the new driver about two weeks ago and my computer is working smoother than ever.

Laurus

1 more replies
Relevance 80.04%

My Event Viewer is showing errors. Most of them are ID - 11 disk errors:"The driver detected a controller error on \Device\Harddisk0\D". Every once in awhile an ID - 5 atapi error: "A parity error was detected on \Device\Ide\IdePort0." shows up.

The only thing I know is that when I disconnect the second HD, the errors still appear, but MUCH less frequently.

Anyone venture a diagnosis?

Thanks!
 

Answer:Event Viewer Errors (disk - 11 and atapi - 5)

How is your power/power supply. I have only seen this once before and the cause was a failing power supply. A drop of voltage during HDD read-write operations. The customer was getting CRC errors during CD-ROM burning. It eventually dropped the HDD out of DMA mode entirely.

Do you know how to check the DMA status in XP?

Start--Control Panel--Performance and Maint.--System--Hardware--Device Manager

Look at the properties of the ATA (IDE) Primay and secondary channels.

Should be DMA if available and DMA mode _

Let me know
 

3 more replies
Relevance 78.59%

Every time I log onto my computer, I enter my password and it looks like its loading to the desktop. Then it prompts me to type it in again for some reason - and the second time it actually does load the desktop.

This just started happening today.

I looked in the event viewer, and I get the same error for every time I turn on my PC or restart...
"The COM+ Event System detected an inconsistency in its internal state. The assertion "GetLastError() == 122L" failed at line 201 of d:\qxp_slp\com\com1x\src\events\shared\sectools.cpp. Please contact Microsoft Product Support Services to report this error.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp."

The link for microsoft help is useless.

The last things I did were...
-set a BIOS supervisor and user password (so you must enter a password to boot the machine and also to enter BIOS setup to make changes)
- Made several changes to "local security policy" (under control panel, administrative tools, local security policy)

I don't see why changing security policy would affect anything. Basically the changes I made were just to make the computer a bit more secure.

I changed the LAN Manager Authentication level to 'send LTNMv2 response only/refuse LM'

I changed "Do not store LAN Manager hash value on next password change" to 'enabled' (default was disabled)
And under 'User Rights assignment' I simply ch... Read more

Answer:errror "The COM+ Event System detected an inconsistency in its internal state."

solved my own problem-

simply creating a new user and restarting the computer fixed the problem.

I have a feeling it had something to do with the LAN Manager hash value setting" I changed.
 

1 more replies
Relevance 78.59%

My computer recently started having issues........ here is what is going on:
* boot computer
* Windows boot screen displayed ~ 1 minute
* screen goes black. Can move mouse. Drive light constantly on, not blinking. ~ 5 minutes
* log in screen comes up / log in
* Desktop loads ~ 1 minute
> sometimes it loads with regular windows aero theme other times it loads with basic windows classic theme.
* Error message pop up "failed to connect to System event notification service"
* Have to wait for about 5 more minutes before computer is actually usable
* The audio service does not work as well...
from when I press the power button to when I can actually use my computer takes 10 - 15 minutes.

Here is what I have tried so far
*Turning off all start up programs / services
*Tested Memory - passed
*Hard Drive Self Test ---- # 1 - 7 fail / I am guessing that this is the source of the problem, however my computer does still work once everything is finally booted. So I don't know what to do with that information or if that test even matters.
* I have tried looking at the event viewer but every time it says that the event log service is unavailable.
> I try turning on Windows Event Log but that does not change anything
* tried "netsh winsock reset" in command prompt, based on a different thread that I found - it didn't work


64bit Windows 7 untimate, clean install from usb iso (post resolution to bootsect.exe issue), running on dell poweredge sc430,
&... Read more

Answer:Windows failed to conect to " system event notification service"

This seems to be a common problem, I am now also experiencing the same.
I have Win 7 Home Premium 64. Did chkdsk /r, defragged, tried sfc/scannow scanned for viruses and even tried reseting winsock.
My aero themes are greyed out, when trying to fix it with MS fixit it errors out.
It takes a long time to boot and then says "failed to connect to System event notification service"

One search on google will show this is a major problem, so why does MS not come out with a fix.
This seems to be the biggest frustration with Win 7 compared to XP, lack of support from MS.

2 more replies
Relevance 78.59%

For the past few weeks I've been having this strange issue with my computer. I would be doing something like browsing the internet or playing a game. Then I would go to access some media files such as music or video's on my media drive and my computer would start acting up. The symptoms I would get is the sound would buzz and scratch, the screen would freeze and stutter, and repeat this every few seconds until my hard drive fails and loses connection all-together.

Then I would have to restart my computer to get my drive back and POST displays that BOOTMGR is missing. I would have to go into BIOS to reset the Boot Order to get my system to boot up and I would get my media drive back.



At first I thought my hard drive was dying, so I took it out and plugged it into another computer to troubleshoot it. Everything seemed to work fine. I even went to the lengths of purchasing a new hard drive, but have yet to install it. I then realized that my video drivers started to act up and crash so I updated those. I believed I had a beta driver and once I got a WHQL driver the problem went away. At least until now...

A week later I was on facebook listening to some music and I went to browse my media drive and to my surprise it instantly started stuttering and freezing again. I'm at the point where I don't know what else to do except replace the drive which I'll probably end up doing this weekend.

I've attached several Event Viewer logs. I could also try capturing... Read more

Answer:System freezes, HDD fails, Event 51 "error during paring operation"

First, change the title of your post. That should be PAGING, not PARING. A lot of people will skip the post not knowing what that is.

All errors indicate a dying hard drive as you suspected. The fact that it works without error in another PC raises the possibility that you may have power supply problems (insufficient power to the drives will produce the same errors), bad cables, or a problem with the SATA controller on the motherboard.

How many physical hard drives do you have in this PC? (Not to be confused with partitions on the same hard drive). If more than one physical hard drive, which one is the problem drive?

9 more replies
Relevance 78.59%

Today I booted up my laptop to get this screen - my desktop without an aero theme and the error message on-screen.

Nothing unusual happened last time I used my PC. No installation or updates that I am aware of.

The computer cannot shut down properly now either, it just hangs after the desktop icons are gone. I am forced to hard shutdown.

http://i.imgur.com/S2N6EGp.jpg


Any ideas?


I doubt its malware but will run scans soon to double check.

Answer:"windows could not connect to the system event notification service"

The service has apparently started though:

http://i.imgur.com/LEuXUAC.png

4 more replies
Relevance 78.59%

I receive this error message in the Windows System log regularly. Device Manager does not show any malfunctioning devices.

Apparently csvol service is part of HFS+ for Windows. This is a program that allows reading of HFS+ file systems on Windows. I did install that.

And I believe these Event ID 7000 errors are related to a service failing to start. maxView Storage Manager Agent service will not start. It is set to 'automatic start' in the Services viewer app. However, I find that it is not started, and if I attempt to start it manually, I receive a message stating it started and then stopped, "Some services stop automatically if they are not in use by other services or programs." That should not be the case with this service.

I'd greatly appreciate any help with this!
- <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" />

<EventID Qualifiers="49152">7000</EventID>

<Version>0</Version>

<Level>2</Level>

<Task>0</Task>

<Opcode>0</Opcode>

<Keywords>0x8080000000000000</Keywords>

<TimeCreated SystemTime="2016-06-19T01:55:30.224060300Z" />

<EventRecordID>33731</EventRecordID&g... Read more

More replies
Relevance 78.59%

I receive this error message in the Windows System log regularly. Device Manager does not show any malfunctioning devices.

Apparently csvol service is part of HFS+ for Windows. This is a program that allows reading of HFS+ file systems on Windows. I did install that.

And I believe these Event ID 7000 errors are related to a service failing to start. maxView Storage Manager Agent service will not start. It is set to 'automatic start' in the Services viewer app. However, I find that it is not started, and if I attempt to start it manually, I receive a message stating it started and then stopped, "Some services stop automatically if they are not in use by other services or programs." That should not be the case with this service.

I'd greatly appreciate any help with this!
- <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" />

<EventID Qualifiers="49152">7000</EventID>

<Version>0</Version>

<Level>2</Level>

<Task>0</Task>

<Opcode>0</Opcode>

<Keywords>0x8080000000000000</Keywords>

<TimeCreated SystemTime="2016-06-19T01:55:30.224060300Z" />

<EventRecordID>33731</EventRecordID&g... Read more

More replies
Relevance 78.59%

Please Help !

My HP running Vista Home Basic suddenly gave me the following error message on startup: "Failed to connect to a Windows service: Could not connect to System Event Notification Service".
Among other things, this prevents me from connecting to my internet network, so I can't get on-line.
Rebooting did not help.

Following the google search I used an elevated command prompt (click Start, click All Programs, click Accessories, right-click Command Prompt, and then click Run as administrator) and typing "NETSH WINSOCK RESET ", then press the Enter key, and then restart the computer.

I still cannot access my internet network, instead of not connection now I get the message "unidentified network" and I still cannot go online although there I have some Mbs

It sais (I do not understand this text )
"What netsh winsock reset command does are it resets Winsock Catalog to a clean state or default configuration. It removes all Winsock LSP (Layered Service Providers) previously installed, including the potential malfunctioned LSP that causes loss of network packets transmission failure. So all previously-installed LSPs must be reinstalled. This command does not affect Winsock Name Space Provider entries."

Please help me with the next step in order to be able to go online from my computer.
Thank you!

More replies
Relevance 78.59%

Both of these snap-ins have died.

I am getting the following errors for both "MMC could not create the snap-in".

I think i might have disabled these by accident due to space left on the primary partition.

Anyone know what checks i can go through to see everything that should be is enabled for both of these admin tools to function. All other admin tools work perefectly.

Any help greatly appreciated.

More replies
Relevance 78.3%

My 6-week-old Dell running Vista Home Basic suddenly gives me the following error message on startup: "Failed to connect to a Windows service: Could not connect to System Event Notification Service." Among other things, this prevents me from connecting to my wireless network, so I can't get on-line. It also prevents several programs within Kaspersky Internet Security from starting. Rebooting doesn't help. And the problem occurs regardless of whether I sign on as administrator or as general user.

More: I can't access the Windows Help & Support pages. And I'm told to "see System Events log" for details, but when I try, it says "Event Log Service is unavailable." When I try System Restore, it says "back-up hasn't been set up." (Aren't restore points set automatically?)

Please help!
 

Answer:"System Event Notification Service" meltdown

14 more replies
Relevance 77.43%

Hello all,
First, is it just me or is the Dell website a little difficult to navigate and sort of annoying? Having said that, I'm not here to trash Dell. I have been, overall, very happy with my Inspiron 3650; however, I have been plagued with some chronic Event Viewer warnings and errors. (As a side note- if there is a particular "group" or "forum" or whatever that discusses Event Viewer messages I would be grateful for that link). While most errors are Windows related, I do get one error which occurs every other day, "Event 0, Dell System Detect"--"The character '/' cannot be included in a name". See below for details.  While it doesn't seem to be causing any immediate problems (other than annoying me), I am concerned that it is affecting my ability to receive updates from Dell. 
Any thoughts would be appreciated! If this is the wrong forum to post this, please advise as well.
Thanks, P.
(Computer name and IP have been redacted)
Log Name:      ApplicationSource:        Dell System DetectDate:          8/13/2017 5:25:53 PMEvent ID:      0Task Category: NoneLevel:         ErrorKeywords:      ClassicUser:          N/AComputer:      V*******aDescription... Read more

More replies
Relevance 77.43%

Hi

After i have removed some spyware/trojans I starting getting this error message when I try to access the eventlog:

event log "unable to complete the operation on" eg. system "the interface is unknown" windows xp.

Also I can add programs to Symantec internet security 2005 firewall, reinstalling don't fix it. Some programs also start to fail, "bad image" or you don't have admin premissions.

Reinstalling SP2 or using system restore for XP don't fix any thing.

I have scanned my computer with 4 antispyware programs, and 4 antivirus programs and check it with hijackthis so my machine should be clean.

Does any one have any Idears?

Answer:event log "unable to complete the operation on" "the interface is unknown" windo

maybe you removes something with hijackthis which your system needs

go to start, run and type "sfc /scannow"
then it will rpompt you for the XP CD, put it in and let it scan your computer for corrupted or missing files

6 more replies
Relevance 77.14%

Hello,
I am getting frequent system related errors in my Event Viewer. Typically those are related to system crashes. Here are four for starters. It is almost impossible to avoid some crashes on a daily basis. I find the M$ help over my head. Where to start??? Thanks in advance for any suggestions.

Event Type: Error
Event Source: SMTPSVC
Event Category: None
Event ID: 116
Date: 4/5/2008
Time: 9:59:08 PM
User: N/A
Computer: HOME-D309DBCB8C
Description:
The service metabase path '/LM/SMTPSVC/' could not be opened. The data is the error code.
For additional information specific to this message please visit the Microsoft Online Support site located at: http://www.microsoft.com/contentredirect.asp.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 03

-------------------------------------------------------------------------------------------------
Event Type: Error
Event Source: Service Control Manager
Event Category: None
Event ID: 7023
Date: 4/5/2008
Time: 8:26:15 PM
User: N/A
Computer: HOME-D309DBCB8C
Description:
The Simple Mail Transfer Protocol (SMTP) service terminated with the following error:
The system cannot find the path specified.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
----------------------------------------------------------------------------------------------
Event Type: Error
Event Source: Service Control Manager
Event Category: None
... Read more

Answer:Frequent Event Viewer Errors

Ozrom1E already answered this post here: http://forums.techguy.org/windows-nt-2000-xp/701214-frequent-event-system-errors.html
 

2 more replies
Relevance 76.85%

Thanks for any help.

Event Type: Warning
Event Source: WinMgmt
Event Category: None
Event ID: 5603
Date: 28/11/2006
Time: 17:57:33
User: USER-2F62D3344E\user
Computer: USER-2F62D3344E
Description:
A provider, OffProv11, has been registered in the WMI namespace, Root\MSAPPS11, but did not specify the HostingModel property. This provider will be run using the LocalSystem account. This account is privileged and the provider may cause a security violation if it does not correctly impersonate user requests. Ensure that provider has been reviewed for security behavior and update the HostingModel property of the provider registration to an account with the least privileges possible for the required functionality.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

Answer:What's this event in event viewer? (event source WinMgmt)

http://support.microsoft.com/default...b;en-us;891642
this might help

1 more replies
Relevance 76.56%

1. Every time I boot up the computer, the following error is generated in Event Viewer:
Source: DistributedCom, Event ID: 10010 

The server {F9717507-6651-4EDB-BFF7-AE615179BCCF} did not register with DCOM within the required timeout.

This key pertains to appID WinInetBrokerServer (CLSID WinInetBroker). I tried adding permissions to the key(s) but that didn't solve the problem. In the permissions for the key, the first user name listed is named Account Unknown (S-1-15-2-1).
I think maybe that may have something to do with it. I deleted the 6 registry keys associated with this key and everything worked but I was locked out of Windows XP Mode (Windows Virtual PC). I was wondering if anyone had any suggestions to fix this error?


2. ALSO, exactly once a day I receive the following warning in Event Viewer:
Source: DNS Client Events, Event ID: 1014 

Name resolution for the name imrk.net timed out after none of the configured DNS servers responded.


It would seem that there is an application on my computer that is trying to connect to this site for whatever reason. I have read about ties between this domain and hacking. Someone suggested to enable boot logging in Process Monitor to try to pinpoint the
app but there's so much going on in Process Monitor I'm not really sure where to look. All of the apps that run on a daily basis (including the ones that are set to run at startup) seem relatively safe to me. I've run the gamut of a... Read more

More replies
Relevance 75.69%

Lately my dad's computer apparently reboots itself often. I'm not there when it happens, apparently there's no error message or anything. I don't know where to look, so I've gone to event viewer and found some errors happen at the time he said it rebooted. These same ones come up every few days in the event viewer. It's an almost fresh install of xp.

One event says: "The System Restore filter encountered the unexpected error '0xC0000001' while processing the file '' on the volume 'HarddiskVolume1'. It has stopped monitoring the volume."
The other says: "The computer has rebooted from a bugcheck. The bugcheck was: 0x0000004e (0x00000099, 0x000779c2, 0x00000000, 0x00000000). A dump was saved in: E:\WINDOWS\Minidump\Mini051814-01.dmp."
These happened around the same time. I don't know if it means anything, so I would like to ask here.

Sorry I do not know what else to provide here.

sysinfo:
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: Intel(R) Pentium(R) 4 CPU 3.20GHz, x86 Family 15 Model 4 Stepping 9
Processor Count: 2
RAM: 2047 Mb
Graphics Card: ATI Radeon 9550 / X1050 Series, 256 Mb
Hard Drives: C: Total - 6412 MB, Free - 6278 MB; E: Total - 59999 MB, Free - 52162 MB; F: Total - 10172 MB, Free - 10106 MB;
Motherboard: Gigabyte Technology Co., Ltd., 8VM800PMD-775
Antivirus: avast! Antivirus, Updated: Ye... Read more

Answer:Frequent reboots, errors showing in event viewer

Hi, does it ever mention - 'PFN_LIST_CORRUPT'
Event Viewer results can at times be misleading.
What date is listed in the result that you posted?
Has any changes been made recently to the system and will it reboot after some time of using or soon after startup?

Some reasons for blue screens
New hardware - software installed.
Device driver - Video driver - corrupted - faulty.
Faulty Ram - overheating - dying hard drive etc.
======
Download BlueScreenView
http://www.nirsoft.net/utils/blue_screen_view.html
Download link at the bottom of the page.

Download > install.
Once it has scanned > Click on Edit > Select All > File > Save Selected Item
It will open in Notepad - or save to Notepad > Copy > Paste and Post the last 5 minidump files from the scan.

Check this link first
======
End of support for Win Xp.
http://forums.techguy.org/windows-xp/1119493-end-support-windows-xp.html
http://www.malwareremoval.com/forum/viewtopic.php?f=4&t=62384#.UssBpPvXvs9
 

1 more replies
Relevance 75.4%

I'm trying to find the settings called "ModemRingOn" and "PME Wake Up Event" both in bios but i can't find them.

Does anyone know where they are? Like under what options in bios?
 

Answer:Where are "ModemRingOn" and "PME Wake Up Event" located in bios?

They may not be there at all. If the modem is built into the board, maybe.
 

1 more replies
Relevance 75.4%

I'm trying to find the settings called "ModemRingOn" and "PME Wake Up Event" both in bios but i can't find them.

Does anyone know where they are? Like under what options in bios?

Answer:Where are "ModemRingOn" and "PME Wake Up Event" located in bios?

BIOS's vary widely; there is no standard features that are included. It's possible your BIOS has neither of them.

If these are features you are interested in exist, the first thing to do is to check the motherboard manufacturer's web site's "support" page, and find out what the latest version of BIOS is available for your motherboard, compare that to what you actually have on your motherboard, and then read the change log to see if possible these features were added.

You can also research these features by Googling the text "ModemRingOn" and the model number of your motherboard "GA-XYZ123" in the same search, in order to filter hits that are limited to those that include references to both of these qualities. Look for forum posts, and other technical sites & information.

Also, look for the User Manual for your motherboard on-line. Sometimes these include information on the BIOS of the motherboard.

1 more replies
Relevance 105.78%

Greetings - I have searched for months but cannot fix this on my own and appreciate any help, please.

Shutdowns occurring in front of my eyes or when I'm not looking; cannot discern any particular software or drivers at fault. Loses all power and stays off, like a power plug pulled. Happens at my home and others as well, with home PSU or my travel PSU (both OEM) and carefully handled over the years, as well as on battery power only.

I had these issues before the new hard drive & Win7 OS installed Sept 2014. Shutdowns began shortly after again; now shutdowns much worse again. Do not believe it's temp related; I run a fan nonstop under the laptop which is in the air on a platform with cooling pad underneath, regularly shoot canned air in; temps read avg mid-40's C and stay displayed in systray, so I watch carefully. Happens with 2 different PSU's, carefully handled, also on just battery power. Did a power drain recently for static buildup; coincidentally or not, was better for a week. Have run chkdisk, memory tests, check for driver updates, and other system tools; no problems detected.

Event viewer seems to have the same patterns leading up to the shutdowns, but things I've tried from searches are ineffective. Here's the pattern, after manually restarting after a blackout shutdown.

Event 219, Kernel-PnP - Warning
The driver \Driver\WUDFRd failed to load for the device WpdBusEnumRoot\UMB\2&37c186b&0&STORAGE#VOLUME#_??_USBSTOR#DISK&VEN_GENERIC-&PRO... Read more

Answer:Frequent Unexpected Shutdowns to No Power-Same Pattern in Event Viewer

  
Quote: Originally Posted by Catherine99


temps read avg mid-40's C and stay displayed in systray, so I watch carefully.

Event viewer seems to have the same patterns leading up to the shutdowns, but things I've tried from searches are ineffective. Here's the pattern, after manually restarting after a blackout shutdown.


mid-40C temps are very good, but how are you monitoring temps? Some progs monitor CPU but not MB (graphics chip). With laptops, it's most often the graphics chip that causes overheat problems.

The two events leading to the shutdown may indicate hardware failure. Is there any connection between shutdowns and moving the unit? Has it ever been dropped?

You might run the machine overnight off a linux boot disk and see if the problem occurs. If so you will have a pretty good idea it's hardware driven.

7 more replies
Relevance 103.73%

I have a message coming up titled "Failed to connect to a windows service"
and it reads -



?Windows could not connect to the System Event Notification Service service. This problem prevents standard users from logging on to the system. As an administrative user, you can review the
System Event Log for details about why the service didn't respond.?





Also, the task bar and menu <g class="gr_ gr_46 gr-alert gr_gramm gr_inline_cards gr_run_anim Grammar multiReplace" data-gr-id="46" id="46">turns</g> into
a classic style of windows randomly when this is happening. This started happening a couple weeks ago to one device regardless of what network it is connected to.



Does anyone have any ideas on how to fix this? We have already reset the NIC on the laptop to force all settings to DHCP to ensure DNS is being set correctly. Updated DHCP settings
to disable NetBIOS as it is deprecated and should not be used over DNS for resolution. And we have run the <g class="gr_ gr_45 gr-alert gr_spell gr_inline_cards gr_run_anim ContextualSpelling ins-del multiReplace" data-gr-id="45"
id="45">winsock</g> reset.



How many devices were affected? - Just oneAre you connected to a domain network? - YesWhen did the issue start happening? - The issue started a couple weeks ago and is getting worse

What we have done so far:

- ... Read more

More replies
Relevance 103.73%

Greetings - I have a major problem of 4-6 shutdowns a day and would really appreciate your help. Here are the specs, description of the problem will follow:
----------------------------------------------------------------
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM)2 Duo CPU T6400 @ 2.00GHz, Intel64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 4062 Mb
Graphics Card: NVIDIA GeForce G 105M, 512 Mb
Hard Drives: C: Total - 476937 MB, Free - 202635 MB;
Motherboard: Compal, 306D
Antivirus: Microsoft Security Essentials, Updated and Enabled
----------------------------------------------------------------

I have searched for months but cannot find a solution to fix this on my own. It's getting much worse suddenly.

Shutdowns occurring in front of my eyes or when I'm not looking; cannot discern any particular software or drivers at fault, no timing pattern. Browser and email open or not; assorted programs open or not. Loses all power and stays off, like a power plug pulled. Happens at my home and other locations as well, with home PSU or my travel PSU (both OEM and carefully handled over the years), as well as on battery power only.

I had random shutdowns before a new hard drive replacement & clean Win7 OS installed Sept 2014. Shutdowns began shortly after again; now shutdowns much worse again. Do not believe it's temp related; I run a fan nonstop und... Read more

Answer:Frequent Unexpected Shutdowns / Black Screen-No Pwr / Repeat Patterns in Event Viewer

16 more replies
Relevance 103.32%

Hi all,

i tried loading the eventvwr.msc file from system32 folder directly as well as from the administrator tools, but i get:

"event log service is unavailable. verify that the service is running."

so i try to start the event log service, from the services.msc program;
whenever i try to start windows event log from services i get the message:

"Windows could not start the windows event log service on local computer.
Error 3: The system cannot find the path specified."

how can i specify the path?
or
how can i resolve the problem?

any help would be appreciated please---thanks

Answer:HELP need to solve this problem asap - Unable to start event viewer/event log service

Fire up regedit and find this key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Eventlog

With "Eventlog" highlighted on the left pane, you should be able to see a value called "ImagePath" on the right. ImagePath should be equal to this:

%SystemRoot%\System32\svchost.exe -k LocalServiceNetworkRestricted

If you can't see "ImagePath" in that location, or if it's not set to the text above, that's almost certainly your problem. If you're in the habit of using "registry cleaners", that might be the cause.

3 more replies
Relevance 103.32%

Hi,
keep getting the errors above every startup regarding;
11 - "Custom dynamic link libraries are being loaded for every application. The system administrator should review the list of libraries to ensure they are related to trusted applications."
7000 - "The Crypkey License service failed to start due to the following error:
The system cannot find the file specified."
7026 - "The following boot-start or system-start driver(s) failed to load:
NetworkX"
1530 - "Windows detected your registry file is still in use by other applications or services. The file will be unloaded now. The applications or services that hold your registry file may not function properly afterwards.
DETAIL -
1 user registry handles leaked from \Registry\User\S-1-5-21-1925592742-456944920-4000667399-1009_Classes:
Process 720 (\Device\HarddiskVolume5\Program Files\Microsoft Security Client\MsMpEng.exe) has opened key \REGISTRY\USER\S-1-5-21-1925592742-456944920-4000667399-1009_CLASSES"
3036 - "The content source <csc://{S-1-5-21-1925592742-456944920-4000667399-1005}/> cannot be accessed.
Context: Application, SystemIndex Catalog
Details:
(HRESULT : 0x80004005) (0x80004005)"
I have 3 admin user profiles.
Each time I login, the loading happens and then I notice my side mouse button of Microsoft Comfort Optical 3000 doesnt operate as customised in Intellipoint 7.00. It takes a long time before it does respond.
If I try to launch event viewer or mouse customisation softwares, they freeze temporarily and ... Read more

Answer:Windows 7: Event errors (11, 7000, 7026), intellipoint and event viewer freeze.

Please download MiniToolBox  , save it to your desktop and run it.
 Checkmark the following checkboxes:  List last 10 Event Viewer log  List Installed Programs  List Users, Partitions and Memory size.
 Click Go and paste the content into your next post.
 Also...please Publish a Snapshot using Speccy - http://www.bleepingcomputer.com/forums/topic323892.html/page__p__1797792#entry1797792 , taking care to post the link of the snapshot in your next post. 
Louis

7 more replies
Relevance 103.32%

I was running 3DMark06 and got a BSOD code 124. After that every time I boot Event Viewer logs Error Codes ID 3012 and 3011. Attached are screenshots of both.

I googled this and found two different threads where someone suggested to rebuild the performance counters. Both responses were basically the same, below is one. Neither of the OP's came back and said if this worked for them.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Re: LoadPerf 3011, 3012
Hi-
I had the same problem with LoadPerf and here is what I found out:
All performance counter names and explain text are maintained in string tables managed by the performance counter subsystem (Perflib).

The current contents of the performance counter string tables are corrupted and cannot be displayed. To correct the problem, rebuild the string tables.

User Action
To rebuild the string tables, on the computer that displayed the message, at the command prompt, type Lodctr /r
The contents of the string tables are automatically rebuilt.

I hope this helps
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Since this was from 2008 (XP?) and the other response was for Vista I wanted to see if the guru's at SevenForums thought that this was okay before I did this.

Here are the screenshoots of my two errors.

Answer:After BSOD Event Viewer Logs Event ID 3012 and 3011 every time I boot

Rebuilding the string tables as outlined in my first post fixed the problem.

1 more replies
Relevance 102.91%

Hi,

I was hoping somebody could offer an insight on the below, as searching around I've not found much to go on other than "overheating"

Basically my laptop has been having very high temperatures for a long time (usually ~60C for CPU and often 100-110 for GPU...insanely high, in other words) For example, see how hot the machine gets just by resuming from a sleep (this is all within a minute or so):



I have been seeing the following error in event viewer each time I start Windows (4 entries) for some time:



So today I bit the bullet and had the back cover off the laptop and noticed what a bad state the thermal compound was in, for both the CPU and the chipset chip, so wiped it off using TIM Cleaner, and then applied new thermal compound and put the laptop back together. I was actually shocked because for the first time since I can remember, I could feel cold air blowing from the vents of my laptop! I logged into Windows and noticed that my temperatures had fallen and were staying at around the below:



Not as low as I'd like but a massive improvement. Trouble is, I am still getting the WHEA-Logger event errors in Windows Event Viewer ('processor core') and wondered if this was not in regards to overheating after all?

The plus side is my laptop is now almost totally silent - the way it must have been when I bought it new 3 years ago! But I was wondering how to investigate these WHEA-Logger errors, if anyone has any advice that'd be great.

... Read more

Answer:WHEA-Logger event 18/19 errors in Event Viewer (W7 Home Premium)

First, well done on applying the thermal paste to the cpu/gpu. I assume you cleaned the vents as well. Did you use arctic silver 5 (just curious)?

I wonder if the processor could have been damaged from the heat. Are you experiencing any BSODs or other problems? You can run Prime95 to test your system. And Furmark for gpu.

2 more replies
Relevance 102.91%

Hi,

keep getting the errors above every startup regarding;

11 - "Custom dynamic link libraries are being loaded for every application. The system administrator should review the list of libraries to ensure they are related to trusted applications."
7000 - "The Crypkey License service failed to start due to the following error:
The system cannot find the file specified."
7026 - "The following boot-start or system-start driver(s) failed to load:
NetworkX"
1530 - "Windows detected your registry file is still in use by other applications or services. The file will be unloaded now. The applications or services that hold your registry file may not function properly afterwards.

DETAIL -
1 user registry handles leaked from \Registry\User\S-1-5-21-1925592742-456944920-4000667399-1009_Classes:
Process 720 (\Device\HarddiskVolume5\Program Files\Microsoft Security Client\MsMpEng.exe) has opened key \REGISTRY\USER\S-1-5-21-1925592742-456944920-4000667399-1009_CLASSES"
3036 - "The content source <csc://{S-1-5-21-1925592742-456944920-4000667399-1005}/> cannot be accessed.

Context: Application, SystemIndex Catalog

Details:
(HRESULT : 0x80004005) (0x80004005)"

I have 3 admin user profiles.

Each time I login, the loading happens and then I notice my side mouse button of Microsoft Comfort Optical 3000 doesnt operate as customised in Intellipoint 7.00. It takes a long time before it does respond.
If I try to launch ... Read more

More replies
Relevance 102.91%

Hi,

keep getting the errors above every startup regarding;

11 - "Custom dynamic link libraries are being loaded for every application. The system administrator should review the list of libraries to ensure they are related to trusted applications."
7000 - "The Crypkey License service failed to start due to the following error:
The system cannot find the file specified."
7026 - "The following boot-start or system-start driver(s) failed to load:
NetworkX"
1530 - "Windows detected your registry file is still in use by other applications or services. The file will be unloaded now. The applications or services that hold your registry file may not function properly afterwards.

DETAIL -
1 user registry handles leaked from \Registry\User\S-1-5-21-1925592742-456944920-4000667399-1009_Classes:
Process 720 (\Device\HarddiskVolume5\Program Files\Microsoft Security Client\MsMpEng.exe) has opened key \REGISTRY\USER\S-1-5-21-1925592742-456944920-4000667399-1009_CLASSES"
3036 - "The content source <csc://{S-1-5-21-1925592742-456944920-4000667399-1005}/> cannot be accessed.

Context: Application, SystemIndex Catalog

Details:
(HRESULT : 0x80004005) (0x80004005)"

I have 3 admin user profiles.

Each time I login, the loading happens and then I notice my side mouse button of Microsoft Comfort Optical 3000 doesnt operate as customised in Intellipoint 7.00. It takes a long time before it does respond.
If I try to launch ... Read more

Answer:Event errors (11, 7000, 7026), intellipoint and event viewer freeze.

Hiya and welcome to SevenForums!
Please contact an admin to move this thread, because this isn't the appropriate section for these kinds of problems.

4 more replies
Relevance 102.91%

when I run reboot stress test at Intel platform with win10 Desktop RS1 version, after some cylces test, XHCI controller show yellow bang. Event viewer showed that event id is 14.  I want to know the indication of
StartDeviceFailReason equals 3. I cannot find more info about this failure from website.Thanks a lot!









-

Provider











[
Name]
Microsoft-Windows-USB-USBXHCI










[
Guid]
{30E1D284-5D88-459C-83FD-6345B39B19EC}




















EventID
14



















Version
0



















Level
2



















Task
0



















Opcode
0



















Keywords
0x8000400000000000

















-

TimeCreated











[
SystemTime]
2016-11-25T19:48:29.908393500Z




















EventRecordID
7099


















Correlation

















-

Execution











[
ProcessID]
4










[
ThreadID]
232




















Channel
System



















Computer
LAPTOP-QQEHB4HS

















-

Security











[
UserID]
S-1-5-18












-

EventData










fid_UcxController
0x187f9ddd64a8







... Read more

More replies
Relevance 102.5%

Hello everyone,

I keep seeing this error appear several times a day, even during idle, in my Event Viewer. I did a clean install of build 10586 less than a month ago. I'm not having any overt issues yet, but the error is disturbing.

SettingSyncHost (9144) {979B90BD-0F81-4D83-B038-62032DD17C47}: Database C:\Users\xxxxx\AppData\Local\Microsoft\Windows\SettingSync\metastore\meta.edb: Index deleteDetection of table items is corrupted (0).
I have spent a few hours researching this and I can't find any reports of similar issues or even what the file metastore\meta.edb is for. Is this hopefully one I can just rename and it'll automatically create a new one?

Answer:Event Viewer Errors: SettingSyncHost, Source ESENT, Event 467

Bump... anyone have any idea? I keep getting it averaging about once an hour.

EDIT: Sorry, forgot to add, already tried /sfc scannow, it doesn't find the error.

2 more replies
Relevance 102.5%

After too many unexplained problems, I decided to reinstall Windows 8.1 Pro x64, and migrate off of SBS 2011 Standard. In addition to the primary workstation that can't read any event logs, I built five Server 2012 R2 servers (Hyper-V host, Active Directory
VM, Exchange 2013 VM, SQL Server 2014 VM, and WSUS VM).

I was diagnosing why my workstation's Outlook cannot reach the local Exchange Server.   I tried to look at the event logs, and found the
Event Viewer cannot open the event log or custom view.  Verify that Event Log service is running (it is) or the query is too long (whatever that indicates).  The request is not supported (50)
Looking at the directory of the event logs folder.  It appears that most logs are empty, which is understandable since it's a rebuilt installation.  I found a small number of Applications and Services Logs and it appears nothing was logged since
six days ago on 4/4/2016.   On support forums, I found many have this exact problem on Win 7, Win 8, and Win 10.  Of the solutions posted none of them would even execute on my Win 8.1 Pro x64 machine.  I tried clearing the event logs (WEVTUTIL
CL logfilename) and am told Failed to clear log .... The request is not supported. 
It's very difficult to diagnose why Outlook 2013 cannot reach Exchange 2013, even if Outlook is installed on the Exchange server machine (just as a test).  The web-based Outlook owa, ecp, ... all work fine. ... Read more

More replies
Relevance 102.5%

The master browser has received a server announcement from the computer MATTSLAPTOP that believes that it is the master browser for the domain on transport NetBT_Tcpip_{18E5B85E-1249-4040-9EF0-5B1F93A7295B}. The master browser is stopping or an election is being forced.



...wtf.
 

Answer:odd event viewer event. my brothers laptop causes errors on my machine?

http://support.microsoft.com/default.aspx?scid=kb;en-us;135464
 

1 more replies
Relevance 102.5%

Hi all,

i tried loading the eventvwr.msc file from system32 folder directly as well as from the administrator tools, but i get:

"event log service is unavailable. verify that the service is running."

so i try to start the event log service, from the services.msc program;
whenever i try to start windows event log from services i get the message:

"Windows could not start the windows event log service on local computer.
Error 3: The system cannot find the path specified."

how can i specify the path?
or
how can i resolve the problem?

any help would be appreciated please---thanks

Answer:Unable to start event viewer/event log service on vista

By the way the OS is a Vista Home Prem without SP1. and i have searched this problem extensively, finding no solutions.

If anyone has any advice it would be greatly appreciated.

19 more replies
Relevance 102.5%

EDIT: ARGH, sorry, meant to post this in General Discussion forum, I have no idea if it is a network issue.

Hello everyone,

I keep seeing this error appear several times a day, even during idle, in my Event Viewer. I did a clean install of build 10586 less than a month ago. I'm not having any overt issues yet, but the error is disturbing.

SettingSyncHost (9144) {979B90BD-0F81-4D83-B038-62032DD17C47}: Database C:\Users\xxxxx\AppData\Local\Microsoft\Windows\SettingSync\metastore\meta.edb: Index deleteDetection of table items is corrupted (0).
I have spent a few hours researching this and I can't find any reports of similar issues or even what the file metastore\meta.edb is for. Is this hopefully one I can just rename and it'll automatically create a new one?

More replies
Relevance 102.5%

Hi.
I have noticed that during the long duration my PC is on (18 hours), several apps keep getting crash. Even after I restart these apps, they will eventually crash. PC is still functioning.
The apps that are crashing are:

Asus AI Suite 2 (I use it for fan control)Corsair Utility Engine - for my mechanical gaming keyboardBitdefender - The Antivirus software doesn't really crash, but it's a module inside BitDefender that has issues.
Bellow are all three event viewer reports for all mentioned apps.
1. Asus AI
Faulting application name: AI Suite II.exe, version: 2.0.0.0, time stamp: 0x00000000
Faulting module name: KERNELBASE.dll, version: 10.0.15063.296, time stamp: 0x28e9cf15
Exception code: 0x0eedfade
Fault offset: 0x000eb802
Faulting process id: 0x3600
Faulting application start time: 0x01d2ee6667bfdd12
Faulting application path: C:\Program Files (x86)\ASUS\AI Suite III\AI Suite II.exe
Faulting module path: C:\WINDOWS\System32\KERNELBASE.dll
Report Id: 64c7a38e-b13e-42ba-bf9f-4b4e72c0cc4b
Faulting package full name:
Faulting package-relative application ID:
2. Corsair Utility Engine
Faulting application name: CorsairHID.exe, version: 1.16.42.0, time stamp: 0x56f25dd3
Faulting module name: ntdll.dll, version: 10.0.15063.0, time stamp: 0xa82cc161
Exception code: 0xc0000005
Fault offset: 0x0005d9f4
Faulting process id: 0x3190
Faulting application start time: 0x01d2eccfcf3748b1
Faulting application path: C:\Program Files (x86)\Corsair\Corsair Utility Engine\CorsairHID.exe
... Read more

Answer:Multiple Application Errors (Event 1000) in Event Viewer

Please use this link to create a zip file so that we can troubleshoot the bsod minidump files and the logs:
BSOD - Posting Instructions - Windows 10 Forums

Please change the default language to English so that we will be able to read and troubleshoot the logs.

2 more replies
Relevance 102.5%

Well, I tryed to manage page-file but unfortunataly it resulted in problems. Then I lost VAIO-CARE and 7 ZIP files too. When I open Event Viewer every single day I see this: event Id 2002, Souce: Eap Host, Log name: Application and number of Eventes: 84. As I am desparate about that, What sould I do? Reinstall VAIO-care or WHAT else? Please help me!!!!! Well, I can say that before of all, I tryed to install vopt, latest version but it was not freeware and I soon had to uninstall it but it was not getting to uninstall from programs and features and then I used register editor to delete the leftovers which desapered from program and features....but I can see several error in event viewr such as Event 11706, MsInstaller >>>> Product Vaio Media Plus -- Error 1706 - An instalation for the product Vaio Media Plus cannot be found. Try the installation again using a valid copy of the instalation package 'VMP VEPMMx64.msi'. So should I reinstall all vaio care or not................!!! By the way I tryed to install vopt in order to align files in hard drive but when I tryed to manage page file it did not work as should have so I lost vaio care..........................................What to do? can you figure out what going on.................!!!

Answer:Event Viewer Event Id 2002, Source: EapHost, Log Application

Welcome to the forums Marioo!

Have you tried a system restore to a point before these errors started? (Easiest things first) You could also try a sfc/scannow, to find and possibly repair any corrupted system files. We have many fine tutorials here at the forums, written by some very knowledgeable people, heres a link to one if you haven't did this before :

SFC /SCANNOW Command - System File Checker

5 more replies
Relevance 102.5%

My Thinkpad W520 has been having an issue where it restarted prompytly and unexpectedly. I thought the issue might be related to the OS or Video driver, and ended up doing clean OS install with no luck. I ran the basic HW tests using Lenovo's utility and the memory, motherboard, and hard disk showed up as healthy.  To me, this seems to be a HW issues, but I am not able to isolate the cause of the problem. Any advice would be appreciated.    

Answer:W520 Restarts Unexpectedly With No Related Event in the Event Viewer

Look in the event log. See if there is an error at the time of the restart. I would do 3 things:1) Run a memory test (probably already done)2) Run a HDD test (Do long test)3) Install TPFANCONTROL to monitor temperatures

6 more replies
Relevance 102.5%

It's been a while since I've experienced a BSOD as I'm viewing a video on youtube. It would freeze as if the audio was caught in mid-stream then BSOD, then would restart automatically. I go to Event Viewer after windows as loaded and I see Event 41 Kernel-Power in there.

I had this issue before and we found out that the motherboard was causing the issue. I have also replaced my video card and added additional memory and expanded to 16gb. Before, I only have 8gb.

Ran sfc/scannow with no errors found. Going to do chkdsk as well.

It's strange because this does not happen at all when I'm playing online games or even just standard browsing. It's when I play videos on youtube that there would be instances where this would happen. There are other times where I can view them without any issue at all.

Any ideas would be great.

Also, how can I attach the windows DMP file to scale it down as it is just really large?

Thanks again guys.

Answer:BSOD when watching videos on youtube, Event 41 in Event Viewer

Hello Santos, and welcome to Seven Forums.

Please read the instructions here: Blue Screen of Death (BSOD) Posting Instructions, and post back with the needed information. One of our BSOD experts should be by later when able to further help.

9 more replies
Relevance 102.5%

EDIT: ARGH, sorry, meant to post this in General Discussion forum, I have no idea if it is a network issue.

Hello everyone,

I keep seeing this error appear several times a day, even during idle, in my Event Viewer. I did a clean install of build 10586 less than a month ago. I'm not having any overt issues yet, but the error is disturbing.

SettingSyncHost (9144) {979B90BD-0F81-4D83-B038-62032DD17C47}: Database C:\Users\xxxxx\AppData\Local\Microsoft\Windows\SettingSync\metastore\meta.edb: Index deleteDetection of table items is corrupted (0).
I have spent a few hours researching this and I can't find any reports of similar issues or even what the file metastore\meta.edb is for. Is this hopefully one I can just rename and it'll automatically create a new one?

More replies
Relevance 101.68%

If a make a password mistake when logging in, event viewer should log event with ID 4625*. But it doesn't. How do I get it too? If you want to know about my computer model Etc. Click on the computer icon next to my name.

(*Event 4625 means Bad password)

Thanks
 

Answer:Solved: Event ID 4625 not being logged in event viewer

I assume you are using Vista or Win 7

The following eventIDs are all related to Login Failures:
4625,4626,4627,4628,4630,4635,4649,4740,4771,4772,4777
 

2 more replies
Relevance 101.68%

While playing war thunder on steam my screen went black and i couldn't do anything. I restart my computer and play again it crashes. After one more time i look at my event viewer and find critical error event ID:41. I don't whether its the game or my pc.

Answer:BSOD playing war thunder, Event viewer event 41

Critical error - Event ID 41 is (most likely) when you forced the system to restart (usually by holding the power button down).

You have a NETGEAR WG111v3 Wireless-G USB Adapter:





I do not recommend using wireless USB network devices. Especially in Win8/8.1 systems.
These wireless USB devices have many issues with Win7 and later - using Vista drivers with them is almost sure to cause a BSOD.
Should you want to keep using these devices, be sure to have Win8/8.1 drivers - DO NOT use Vista drivers!!!
An installable wireless PCI/PCIe card that's plugged into your motherboard is much more robust, reliable, and powerful.



I noticed that you don't have Secure Boot and/or UEFI enabled. If you were having problems with it and changed it, please let us know.





It's not necessary to enable it now. But, should you reinstall Windows at some point in the future, please enable it first.

I mention this because it may happen that (one day) the system won't boot. This can be caused by a program changing your UEFI settings, or an update of the UEFI resetting it to default values.

To test and see if this is the cause, boot into the UEFI and see if the settings have been changed. If uncertain, try with Secure Boot both on and off (and the UEFI on UEFI or Legacy (CSM))

If it still doesn't boot after trying this, then move on to other troubleshooting tools as it's not likely to be due to this.



Black screen errors are not... Read more

1 more replies
Relevance 101.68%

I tried a lot, but couldn't find the event log for the cleanmgr.exe (Disk Cleanup) in the Event Viewer.
Actually, I need the source & event id of cleanmgr.exe to schedule a task in the Task Scheduler.

Answer:In Event Viewer, Where is event log for cleanmgr.exe (Disk Cleanup)?

This Article would be of services to you .

3 more replies
Relevance 101.68%

I have updated Windows 10 Pro to the Creators update. I have had a few event viewer errors which I managed to fix. But I don't know what this one is, I guess everyone is seeing it, does anyone knoe how is it resolved? Thanks.

"Windows Hello for Business provisioning will not be launched.
Device is AAD joined ( AADJ or DJ++ ): Not Tested
User has logged on with AAD credentials: No
Windows Hello for Business policy is enabled: Not Tested
Local computer meets Windows hello for business hardware requirements: Not Tested
User is not connected to the machine via Remote Desktop: Yes
User certificate for on premise auth policy is enabled: Not Tested
Machine is governed by none policy."

Answer:W10 Creators update Event viewer error Event ID 360

Only workaround if you are fine with it.
Managing Windows 10 Creators Update rollout for a seamless experience - Page 7 - - Windows 10 Forums

1 more replies
Relevance 101.68%

Not sure if this is the right section, if not please move to the correct one.

Under the details tab in Event Viewer when a logged event has a GUID that shows up in the registry under HKEYLM > System > CurrentControlSet>Control>WM>Autologger>EventLog-XX I know how to disable the event from logging, but Event ID 15 - ACPI does not have a GUID.

Does any one know how I can get this to stop logging? From what I have seen on the web only a fix to the motherboard BIOS would fix it and I doubt that this is high on Asus' list of BIOS fixes for the R6E. Everything I have read on the web says that this is meaningless and in the General tab it basically says to ignore it so I would like to get this to stop logging in Event Viewer.

More replies
Relevance 101.68%

I wanted to see who was viewing my computer and went to event viewer, under System > filter current log > power troubleshooter -- I found that the wake source for the system resuming from sleep was a device usb root hub, what does this mean?

More replies
Relevance 101.68%

Every time I boot my laptop I get error message Event ID 10 in Event Viewer. The details are:

Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor"AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected.

I do believe that the error message is nothing to be concerned about from what I have read when I googled it, but nothing I read tells you how to get rid of it. Does anone know how I can get rid of this so it does not show up in event viewer everytime I boot?

Answer:Event Viewer Error Message Event ID10 - How to get rid of it?

idahosurge,
Read through the link below...
Hope it helps with your problem.

Event ID 10 is logged in the Application log after you install Service Pack 1 for Windows 7 or Windows Server 2008 R2

5 more replies
Relevance 101.68%

A week ago I started getting this warning errors logged three to six times or more per day in Event Viewer.

Event Viewer Warning - Source is e1yexpress - Event ID is 27
Intel(R) 82567V-2 Gigabit Network Connection Link has been disconnected.

Every time Event Viewer logs the e1yexpress warning it follows up with this logged warning
Event Viewer Warning - Source is DNS Client Events - Event ID is 1014
Name resolution for the name isatap.home timed out after none of the configured DNS servers responded.

Not every time, but a lot of times Event Viewer also logs this warning right after it logs the isatap.home warning.
Event Viewer Warning - Source is DNS Client Events - Event ID is 1014
Name resolution for the name teredo.ipv6.mocrosoft.com timed out after none of the configured DNS servers responded.

Today I installed updated drivers for my Intel(R) 82567V-2 Gigabit Network Connection, but after 11 hours of no logged error warnings they started up again and I got three sets of the above logged in a 90 minute time frame.

My system is two years old and as far as I know I have never had these errors logged before.

My motherboard is a Asus Rampage III Extreme.

Any ideas on how to get event viewer to stop logging these? A google search really did not offer any real clues on what to try other than updating my Intel(R) 82567V-2 Gigabit Network Connection drivers, which did not solve the problem.

Answer:Event Viewer Warning - Source e1yexpress - Event ID 27

Well after trying everything google came up with to try, including updating drivers to the latest version, rolling drivers back to the default Win7 version, disabling SIPS and a few others things I decided to call Verizon and see what they had to say. As soon as I told Verizon Tech Support that my error code was "e1yexpress - Event ID is 27
Intel(R) 82567V-2 Gigabit Network Connection Link has been disconnected", they told me not our problem take your PC to a shop. I called back a couple of hours later and talked to a different person and this time I only said that I was getting the Event 1014 time out errors. They had me do a few things in a cmd prompt and then said we do not know, but we can send you a router, I said fine, I will try the router.

Well it has been over a week since installing the new router and no error codes at all so it was the router!

2 more replies
Relevance 101.68%

Every time I boot my laptop I get error message Event ID 11 in Event Viewer. The details are:

Custom dynamic link libraries are being loaded for every application. The system administrator should review the list of libraries to ensure they are related to trusted applications.

This is listed under AppInit_DLLs in the registry and the dll being loaded is nvinitx.dll, from what I can find out this has to do with the optimus function on my laptop and having it loaded is okay. I just want to get rid of the error message being logged everytime I boot.

Answer:Event Viewer Error Message Event ID11 - How do I get rid of this to?

Does anyone have any ideas on how to get rid of this error message in Event Viewer?

2 more replies
Relevance 101.68%

I keep getting this error message in the application log of the event viewer.



I haven't been able to figure out which application I run which produces this error. It might be Windows Defend when it scans. I'm really not sure though. Can anyone give me any insight to this error.

I have Googled this, but nothing I see makes any sense to me. Maybe someone can simplify it for me. Thanks.
 

Answer:Userenv, Event 1000 Error in Event Viewer

HI!
This helped me when I had the same problem...check it out.
User Profile Hive Cleanup Service
http://www.microsoft.com/downloads/...6D-8912-4E18-B570-42470E2F3582&displaylang=en





Overview
The User Profile Hive Cleanup service helps to ensure user sessions are completely terminated when a user logs off. System processes and applications occasionally maintain connections to registry keys in the user profile after a user logs off. In those cases the user session is prevented from completely ending. This can result in problems when using Roaming User Profiles in a server environment or when using locked profiles as implemented through the Shared Computer Toolkit for Windows XP.

On Windows 2000 you can benefit from this service if the application event log shows event id 1000 where the message text indicates that the profile is not unloading and that the error is "Access is denied". On Windows XP and Windows Server 2003 either event ids 1517 and 1524 indicate the same profile unload problem.

To accomplish this the service monitors for logged off users that still have registry hives loaded. When that happens the service determines which application have handles opened to the hives and releases them. It logs the application name and what registry keys were left open. After this the system finishes unloading the profile.Click to expand...

Hope it works as well for you!

 

3 more replies
Relevance 101.68%

From what I understand about the event log in Windows 7, when someone tries and is unsuccessful when logging into the computer the event log should record an event id 4625. However this is not happening at either of my Windows 7 Ultimate machines. I found an identical thread about this problem where the user found a solution but did not specify what is was.

http://forums.techguy.org/general-security/995501-solved-event-id-4625-not.html

Any ideas?

Thanks
 

Answer:Solved: Event ID 4625 not being logged in event viewer

Are you creating a Custom View ? Be sure that you have selected 'By Log - Event Logs: Windows Log, Security. Then except for the Event ID field, everything should not be checked.
 

3 more replies
Relevance 101.68%

I have noticed these in my event viewer appearing a lot and roughly around times when my computer decides to freeze up on me.

Event ID 7001, Service Control Manager
The Peer Networking Grouping service depends on the Peer Name Resolution Protocol service which failed to start because of the following error:
%%-2140993535

&

Event ID 7023, Service Control Manager
The Peer Name Resolution Protocol service terminated with the following error:
%%-2140993535

Answer:Event ID 7001 and 7023 Shows in Event Viewer a lot.

Just FYI - I usually ignore these errors when they show up.
BUT, if they're associated with freezes we'll need to have a deeper look.

Please post this info even though you're not reporting BSOD's: http://www.sevenforums.com/crashes-d...tructions.html

7 more replies
Relevance 101.68%

My Win 7 Pro x64 system just started acting up. When I select an event in the Event Viewer, the More Information: Event Log Online Help link doesn't open IE10. When I click on the link, the Event Viewer pop-up confirmation box open to confirm sending information across the internet, but when I click "Yes" the box goes away and I get a momentary indication from the cursor that the action is processing then nothing. It will not change the active IE10 page or open IE10.

Is there a solution with out a system restore?

Thanks in advance for your assistance.

Regards

Answer:Event Viewer Event Log Online Help Links don't function

I don't know much about this kind of stuff - but here is what I dug up using Microsoft's Process Monitor and Process Explorer.

The mmc app (event viewer) sends info to one of the svchost instances (netsvcs).

Svchost writes some info to the registry about a scheduled task and then runs that task.

This starts taskeng - which starts wscript.

Wscript runs a temporary VBS file that is supposed to send a URL to the operating system (shell).

The OS is supposed to open your default browser.

Here is the contents of the VBS file from my testing:

Code:
Set shell = createobject("wscript.shell")
Shell.run """C:\Users\username\AppData\Local\Temp\tmp78C0.url"""


You might try SFC /SCANNOW Command - System File Checker

And let's hope that some other forum member can suggest things that you should check.

4 more replies
Relevance 101.68%

Welcome,
I have a problem. Every day I have this error in event viewer, system log:
{Registry Hive Recovered} Registry hive (file):\??\C:\ProgramData\Malwarebytes\Malwarebytes Anti-Malware\S-1-5-21-4089430802-3287748835-2730757419-1001-0-ntuser.dat was corrupted and it has been recovered. Some data might have been lost.
This error repeats every day at about 3:00AM.
Maybe someone could help me? Thanks in advance.

Answer:Event ID 5 Kernel-General error in Event Viewer

Hi:

Just curious:
Are you running MBAM Premium (paid version), or Free?If it's Premium, what time does your scheduled daily Threat scan run? (Assuming you are running a daily Threat scan, which is the default scan schedule.) (Dashboard > Settings > Automated Scheduling > Threat Scan > Edit)

Thanks,

MM

7 more replies
Relevance 101.68%

My computer seemed to be running more slowly after the Creators update, so I went into the error viewer and found a ton of errors with the source EapHost, Event ID 2002. From Googling around, I found that this error can be caused by leftover keys from Cisco software, so I went ahead and deleted two of the keys referred to in the error logs, and the errors associated with those keys stopped popping up. However, there's a third error that keeps popping up:

Skipping: Eap method DLL path validation failed. Error: typeId=21, authorId=311, vendorId=0, vendorType=0

The trouble is that this doesn't give me enough information to figure out which key I need to delete. It refers me to a node in the registry called WLANProfileCreationUXAuth. There are six subfolders under that one, and some of them contain keys that I can't delete. (Stupidly, I tried, but the system wouldn't let me.)

What I'm wondering is this: how can I figure out which of the specific keys I need to delete? None of them refer to Cisco, as far as I can see.

More replies
Relevance 100.86%

My computer boots and loads the Window XP without problem. But just
after that or sometimes a while later, it hangs. I have checked the
event viewer and have found the following message: "Error. Disk Event
ID 11 and atapi ID5.

More replies
Relevance 100.45%

Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz, x64 Family 6 Model 23 Stepping 6
Processor Count: 2
RAM: 3325 Mb
Graphics Card: NVIDIA GeForce 9800 GT, 512 Mb
Hard Drives: C: Total - 466635 MB, Free - 283303 MB; D: Total - 10239 MB, Free - 3492 MB; G: Total - 476821 MB, Free - 37511 MB;
Motherboard: Dell Inc, 0PP150, A00, ..CN7082186G50HH.
Antivirus: Norton Security Suite, Updated and Enabled

Error message appears on startup, usually clears upon clicking "Try again", then computer runs normally. It appears to boot up somewhat slower as well.
 

More replies
Relevance 99.63%

Hi, I have a strange thing going on with Event 1 in the Even Viewer.
Event 1 signifies that the computer awoke from sleep (standby/hibernation), see attachment below for illustrations. It shows the time (circled in blue) which is also the time it shows in the list with all the other events, and that is the actual time the event occurred. But if you look on top of the box (circled in red) you see weird times listed over there, in fact at the time that the event take place (9:08 in this case) the times listed above didn't arrive yet. Why are those future times there, and how does the computer write something form the past into the future? I find that very strange. Do you perhaps know how that could happen?

Thank you, I appreciate it!
 

Answer:Event Viewer - Event 1 has weird times in it

16 more replies
Relevance 99.63%

Greetings,

I have a large number of the following errors in my event viewer:
Level|Source|Event ID|Task Category
Error|spdt---|------4|--- none

General--
Driver detected an internal error in its data structures for .

Details--
__________
XML View--
- <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="sptd" />
<EventID Qualifiers="49156">4</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-06-25T05:25:52.106802800Z" />
<EventRecordID>83268</EventRecordID>
<Channel>System</Channel>
<Computer>adm-PC</Computer>
<Security />
</System>
- <EventData>
<Data />
<Binary>000000000100000000000000040004C0530000000000000000000000000000000000000000000000</Binary>
</EventData>
</Event>
__________
Here is the Friendly View--
-System
-Provider[ Name] sptd
-EventID4[ Qualifiers] 49156
Level2Task0Keywords0x80000000000000-TimeCreated[ SystemTime] 2011-06-25T05:25:52.106802800Z
EventRecordID83268ChannelSystemComputeradm-PCSecurity
-EventData
000000000100000000000000040004C0530000000000000000000000000000000000000000000000
Binary data:

In Words
0000: 00000000 00000001 00000000 C0040004
0008: 00000053 00000000 00000000 00000000
0010: 00000000 00000000

In Bytes
0000: 00 00 00 00 01 00 0... Read more

More replies
Relevance 99.63%

I have a pavilion desktop h8-1075, and have found the following comes up in error of event viewer every so often

iaStor did not respond within the timeout period event 9

any assistance would be great to see if someone can cure this issue

Pavilion Desktop hpe h8-1075uk
Win 7/Pro
16 Meg ram

Tony Miller

Answer:Event Viewer error iaStor Event 9

Iastor is your storage driver (for HD or Raid) and often a driver will not respond within the normal range. No big deal but you can update the driver to newest version to see if that eliminates the messages

2 more replies
Relevance 99.63%

Hi Guys/Girls

I keep getting this error every 30 minutes anybody managed to solve this ?

Log Name: System
Source: Microsoft-Windows-DistributedCOM
Date: 30/10/2016 11:54:11
Event ID: 10010
Task Category: None
Level: Error
Keywords: Classic
User: DALE-PC1\Dale
Computer: Dale-PC1
Description:
The server {4AA0A5C4-1B9B-4F2E-99D7-99C6AEC83474} did not register with DCOM within the required timeout.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-DistributedCOM" Guid="{1B562E86-B7AA-4131-BADC-B6F3A001407E}" EventSourceName="DCOM" />
<EventID Qualifiers="0">10010</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x8080000000000000</Keywords>
<TimeCreated SystemTime="2016-10-30T11:54:11.788175700Z" />
<EventRecordID>18568</EventRecordID>
<Correlation />
<Execution ProcessID="8" ThreadID="9028" />
<Channel>System</Channel>
<Computer>Dale-PC1</Computer>
<Security UserID="S-1-5-21-4124590474-3230443324-182549641-1022" />
</System>
<EventData>
<Data Name="param1">{4AA0A5C4-1B9B-4F2E-99D7... Read more

Answer:Event Viewer keeps showing Event ID 10010

Hi,

It's a synchronization error. The server trying to sync to a device that is no longer present or was just never there.

Try to disable the following service: Portable Device Enumerator Service (WIN+R > Services.msc) and see if that helps.

Cheers,

1 more replies
Relevance 99.63%

Hi there,

It's my first time posting on this forum however this forum has helped me solve dozens of past issues so thanks

Ok so I've got an MSI GS40 notebook running Windows Home 64-bit. It's a great notebook and runs like a dream. I recently checked my Event Viewer and saw thousands of warnings. Basically the same warning every second. They're all Execution Service - Event ID: 1

I'm really not keen on a system restore or reformat. The hardware is pretty high-end and so it doesn't seem like anything has slowed down but I would like to resolve these crazy warnings.

Any help would be great...

More replies
Relevance 99.63%

I keep an eye on the event viewer and a new event I haven't seen before has showed up. The event is under the application heading as information and the source is (ESENT). It reads as follows:

Event Type: Information
Event Source: ESENT
Event Category: General
Event ID: 100
Date: 8/16/2004
Time: 5:20:33 AM
User: N/A
Computer: ALPHA
Description:
wuauclt (1272) The database engine 5.01.2600.0000 started.

Everything is the same on the next three events except the discriptions which are as follows:

wuaueng.dll (1272) SUS20ClientDataStore: The database engine started a new instance (0).

wuaueng.dll (1272) SUS20ClientDataStore: The database engine stopped the instance (0).

wuauclt (1272) The database engine stopped.

This happens several times a day. Everything seams to be working properly but I very interested in what this data is trying to tell me.

Thanks
John
 

Answer:Strange new event showing up in event viewer.

9 more replies
Relevance 99.63%

Hi there,

It's my first time posting on this forum however this forum has helped me solve dozens of past issues so thanks

Ok so I've got an MSI GS40 notebook running Windows Home 64-bit. It's a great notebook and runs like a dream. I recently checked my Event Viewer and saw thousands of warnings. Basically the same warning every second. They're all Execution Service - Event ID: 1

I'm really not keen on a system restore or reformat. The hardware is pretty high-end and so it doesn't seem like anything has slowed down but I would like to resolve these crazy warnings.

Any help would be great...

More replies