Computer Support Forum

Need manual for LANParty UT NF3 250GB

Question: Need manual for LANParty UT NF3 250GB

I have looked all over the internet and cannot find it.

looks like DFI took all the support pages down as well! Any help would be greatly appreciated!!!!

Relevance 100%
Preferred Solution: Need manual for LANParty UT NF3 250GB

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

Answer: Need manual for LANParty UT NF3 250GB

Found it yet?

Hey there,

Just wondering if you found the manual yet?
I am looking everywhere to try and find one but no luck yet...

Cheers

9 more replies
Relevance 75.4%

So yeah, i have a Lanparty UT nF3 250GB Mobo. Not 100% on what goes goes where. Unable to locate a users manual online. The wires are as follows:

4pin white / open / black / red with the same 4pin connection on the other side

(Qty. 2) 4pin red VCC / white USB2- / green USB2+ / black GND with a separate 1pin GND

2pin red / white -> H.D.D. LED

2pin orange / white -> POWER SW

2pin blue / white -> RESET SW

Welcome to how to wire your mobo 101. Really need some help figuring out where these go. Thx
 

Answer:Need help with wiring Lanparty UT NF3 250gb mobo, lost manual

Try this http://www.dfi.com.tw/portal/CM/cmp...normal&mode=view&downloadFlag=true&itemId=472
 

4 more replies
Relevance 79.13%

Hi,

I was wondering if LANParty UT NF3 250Gb Motherboard is good for gaming or other usage. How reliable is this motherboard ?

Thank you
 

Answer:LANParty UT NF3 250Gb MoBo

http://www.anandtech.com/mb/showdoc.aspx?i=2198
 

1 more replies
Relevance 78.31%

Today, I found out that my house cleaners threw out my cd...So now I need to find a new one or just the files. I know the website, but not the driver I need.
http://us.dfi.com.tw/
That is the site. I have tryed a few, but there not the right ones.

I have Windows Xp Home Edition and LANPARTY UT nF3 250Gb.
I just need the same one as the cd. I will have more information soon if I find my manual.
 

More replies
Relevance 76.67%

hi, i have a cd player with s/pdif out on the back, and i plugged it into the s/pdif in on my DFI LANPARTY UT Nf3 250gb motherboard, and i'm trying to get it to play through my speakers. i have the speakers plugged into the onboard 8 channel sound card. also, if it helps, i have an audigy zs 2 in the comp as well, but for this i have the nvidia sound set as default.
 

Answer:S/PDIF IN Playback problems on NF3 onboard DFI LANPARTY UT Nf3 250gb

I have the same problem I have no idea what to do ima just call the sound card manufacturers...
 

1 more replies
Relevance 68.88%

Hey all I was just wondering if anyone knows about the nVIDIA Firewall(Embedded hardware firewall) on the DFI Lanparty UT 250gb and if there is anyone to disable it or set port forwarding or permissions on this firewall. Where is it at...how do you get to it etc. Any help would be great! Thanks!
 

Answer:nVIDIA Firewall(Embedded hardware firewall) on the DFI Lanparty UT 250gb

I think you can do it by just going to http://localhost in the browser.
 

2 more replies
Relevance 45.51%

Hi, I want to buy a new hard drive for my desktop PC, and I was wondering if the western digital black 250GB hard drive or western digital enterprise 250GB hard drive would work better for such a PC. Both of the HDDs I mentioned are SATA, in case you're wondering.
 

Answer:Solved: western digital black 250GB vs. western digital enterprise 250GB

13 more replies
Relevance 45.1%

Hi

I noticed that some services of Windows 10 Preview although I set them on Manual, they are automatically set to "Manual (trigger start". Why? What is the difference between these two startup modes?

Lastly, with these services, how do I set them to the first startup mode without that they are set to the second startup mode?

Thanks

Bye

Answer:Difference between the Manual and Manual (trigger start) services

This will answer most of your questions:

Windows service trigger start - difference manual vs automatic? - Server Fault

7 more replies
Relevance 42.64%

Does anyone have any idea when I can expect a release date for this MotherBoard

http://www.dfi.com.tw/Product/xx_pro...YPE=LP&SITE=UK

Answer:LANPARTY UT nF4 SLI-D

thats a nice board

9 more replies
Relevance 42.64%
Question: Dfi lanparty

Im confused on the DFI lanparty skt 939. I was looking at the ones that support pci express and there are so many different ones. They say thaey support pci express x 16 (2). Does that mean that you have to use 2 video cards? And whats the deal with pci express x1, x4 and x16? If I wanted to run 1 evga 9600 pro pci express which 1 would I be looking at? Possible to give me a link to one? Obviously on N.E.

Answer:Dfi lanparty

well if it has 2 pci-e its SLI dude.

9 more replies
Relevance 42.64%
Question: DFI's Lanparty

Hey guys, in a recent form, my mobo just generally freaked out on me, so i'm buying a new one:unch: . My memory that i have is CORSAIR ValueSelect 1GB (2 x 512MB) 184-Pin, and i've read reviews that this mobo doesn't react to that memory very well. I started looking at the ASUS A8N-SLI Premium, but people have said to have problems with that board too with Corsair memory. Does anyone have any experience with these two boards and the Corsair ValueSelect memory?? Thanks!
 

More replies
Relevance 42.64%

Hi guys!

I just installed a Zalman 7700 ALCU on my Venice 3200+ on a DFI Lanparty Ultra-D NF4 mobo. Please read the whole description guys, there are a few twists and turns.

The 7700 comes with something called a Fan Mate 2 which allows you to control the speed of the CPU fan.

The thing is, when I turn the knob of the Fan Mate 2, the CPU fan does NOT change speed! It stays at the same speed, when connected to the 3 pin "CPU fan slot".

The BIOS Health Monitor tells me the fan is spinning at 800 something RPM when on slow setting. When the speed is attempted to be "increased" using Fan Mate 2, even though the fan is spinning at the same speed, the "CPU fan speed" in the BIOS goes to ZERO. (instead of both getting INCREASED)

When I use ANOTHER 3-pin fan input slot other than "CPU fan input slot" (e.g. Fan 2 slot), the speed increases to like 1700 something. So the "Fan Mate" thing is doing something right. Even though both numbers (800 and 1700 something) are less than the "stated" speeds of 1000/2000 +- 10%. (e.g. 900-1100 and 1800-2200 for the two modes). I guess this is another problem altogether.


Now, I INITALLY thought there was a problem with the 3-pin CPU fan slot. But the thing is, when I START the computer with the 7700 connected to the 3 pin CPU fan slot, it actually spins pretty fast (around 1700). But, as the computer is POSTing it slows itself down to like 800.. After that, as describe... Read more

Answer:DFI Lanparty CPU fan help!

Bump! C'mon guys! I am sure someone knows the answer to this? Thx!

5 more replies
Relevance 42.64%
Question: Lanparty?

ok well i was wondering where i could find a NF2 ultra400 DFI Lanparty board. i know they made one cause i always wanted one since they came out but i just cant find them anymore!! know whre i can get one?

Answer:Lanparty?

if it's not at newegg.com, zipzoomfly.com, monarchcomputers.com, or mwave.com I don't know

9 more replies
Relevance 42.64%

Hi there

I was just wondering if anyone can slove my litttle problem here.... all it is, is that the USB 1.1/2.0 ports on my DFI LanParty nF4 SLI-DR Motherboard aint actually running @ USB 2.0 speeds, instead they are running at 1.1 speeds, and it actually says when i plug something in "Get more from this device blah blah by plugging it into a USB 2.0 port"

Can anyone help me with this? Just cant figure out why it wouldnt be running at USB 2.0 speeds. Thanks

My Motherboard

Moja

Answer:LanParty SLI-DR - USB 2

Edit: Here are the options in BIOS were (*) represents the option currently selected:


Quote:




USB Memory Type
-SHADOW (*)
-Base Memory (640K)

OnChip USB
-Disabled
-V1.1+V2.0 (*)
-V1.1

USB KeyBoard Support
-Enabled
-Disabled (*)

USB Mouse Support
-Enabled
-Disabled (*)

USB Park Mode
-Enabled
-Disabled (*)

USB TD Reads
-ISO Queue (*)
-non-ISO Queue

USB Data Reads
-ISO Queue (*)
-non-ISO Queue

USB Asyn Data Reads
-ISO Queue
-non-ISO Queue (*)




Moja

1 more replies
Relevance 42.64%

I have a DFi Lanparty NF4 SLi-DR Motherboard. It can run with 2 x 1GB Corsair XMS3200 Pro RAM but when I try to run with 4 x 1GB of the same RAM it won't boot up. Can anybody help? The processor I am running is an AMD64 3500 with 2 x 7800GT OC Graphics Cards running in SLi configuration. The case is a Thermaltake watercooled Tai-Chi with a Thermaltake W0073 modular 520w PSU. I am running 2 x 300GB Maxtor Maxline 3 Hard-drives placed into Vantec Vortex HDD coolers. I have listed the system in case it helps.

Answer:Cannot run 4GB RAM with DFi LANPARTY SLI DR

They are lots of reasons why.The major one will be the ram. If it is double sided ram, then the maximum the board will take is 2 X 1Gb modules. If the ram is single sided then the motherboard can take 4 X 1Gb modules but you have to alter the memory timing in the bios. It has to be changed from 1T ( command per clock) to 2T. Also the memory voltage has to be altered to 2.8v.Page 7 of manual

1 more replies
Relevance 42.64%

hey my freind got thesame bord as me UT model though and on his raid array when installing windows gives him a error IRQL_NOT_LESS_OR_EQUAL can any one help

Answer:DFI lanparty UT sli-dr

This is a common problem and I have run into it more than enough times.

First thing to do is make sure your memory is working fine by running memtest for a few hours.

If memory turns out to not be the problem, go into your BIOS and disable all components that are not neccesary and remove all unneccesary periphiral cards (eg modems, sound cards, onboard LAN etc.) and try again. If this works, go back into the BIOS and turn them back on one by one and make sure the system boots. If it doesn't, one of your components probably has an IRQ conflict

If you successfully are able to install Windows, I suggest you install the HAL (Hardware abstraction layer) which allows you to manually assign IRQs and avoid conflicts

http://support.microsoft.com/default...b;EN-US;299340

4 more replies
Relevance 42.64%
Question: DFi Lanparty

So I built a computer, and I got the DFi Lanparty with the SLi and all that. Werid thing is it comes with 2 Ethernet plugs. I can get internet from either one, but there must be a reason they put 2 plugs in there. So i thought it was for that whole "lanparty" thing. so i hooked another computer to the other plug, and it lights up, the other computer says it gets a connection, but it isn't strong enough to actually get on the internet. So, anyone have this board or know what it's there for?
 

Answer:DFi Lanparty

Most new High end boards(like that one) are coming standard with Dual ethernet. I think you got it right with the reason for being LAN parties.
 

1 more replies
Relevance 42.23%

Currently i have 1gig(2 sticks of 512MB) of ram in my DFI LanParty nF4 SLI-DR mobo. One in the 2nd dimm slot and one in the 4th(total of 4 dimm slots) I just bought a stick of 1GB memory with the same specs but when i put it in the system, it will not boot at all. I tried every stick in every slot but cant get it to work. If i take out both old memory sticks and put the new 1gb stick in dimm slot 2 the system will boot, but i cant get both to work together? anyone have any idea? thanks! its PC3200 DDR400 ram
 

Answer:RAM in my DFI LanParty Mobo

ttt anyone?
 

10 more replies
Relevance 42.23%

So I figured out what it was, DIMM Slot 4 was bad. I figured this after running MemTest for two hours. The sticks are fine, and in single channel mode it ran fine but once in DDR it would start coming up with errors after about half an hour. Just wondering if anyone has had this problem before?
I returned the mobo for a new one, hopfully that will fix it.

-Ryan

More replies
Relevance 42.23%

How is the AM2 DFI LanParty aside from it's looks? (Found here: http://www.newegg.com/Product/Product.asp?Item=N82E16813136014)

... Anyone have it or know it well? How is it? Stable? Good OCing?

Also, it seems to need an 8-pin CPU plug... What version of ATX is that? My PSU is only 2.01 ATX, and thus doesn't have the 8-pin plug for the CPU . Any way to make it work? The PSU is only a few months old and is VERY good for my needs (480W), and is 100% stable. I don't want to replace it!
 

Answer:*drool* DFI LanParty

Hmm.... well, if no one knows about the board, anyone atleast know the question about whether there is a way to use a 4-pin powersupply on an 8-pin motherboard (CPU plug).
 

4 more replies
Relevance 42.23%

A buddy of mine says F*&^ DFI and go with Abit AN8, anyone wanna tell me if there is any truth behind this? Or what one more over people like and have had better experiences with?

-Ryan

Answer:Abit AN8 or DFI LanParty?

if you can afford the DFI go with it, it seems to be a better board, and everyone will recomend it.

9 more replies
Relevance 42.23%

I built a system using a DFI Lanparty board using IDE raid 0, which the board was made for (not ATA), with W2k, SP4. I used 2 160g drives to do this, used good components, lots of memory, etc. It worked fine for quite awhile, until I added an MT 4 sound card for the purpose of in house music recording and editing (I'm also a part time musician). Almost immediately, it started to hang, so I decided to uninstall the card and software. Did that, then when I rebooted the system, at the last stage of the boot process, just when you think everythng is cool, I get a blue screen registry error message. I am no programmer, but I do know a lot of basic recovery methods, and none of them worked. My main question is this- is there bootable software available on CD that I can use to address this registry error issue, or is there another approach? Keep in mind that I can get to a command prompt screen that allows me to see that all the files are still there with a directory command, yet cannot boot in safe mode or any other F8 option, even when I use the W2k CD. I still get the blue screen error message which passes very quickly, something like ...security.ini..., and then the system reboots, like in a loop, and goes back to the same blue screen error message, then reboots, ends up at the same blue screen, etc. If you have any input, please let me know at '[email protected]'
 

Answer:DFI Lanparty IDE hangup

This is 'also' your thread right?

http://forums.techguy.org/windows-nt-2000-xp/430889-dfi-lanparty-ide-hangup.html

You must not post 2 threads, use the 'Post a Reply!' button.
 

2 more replies
Relevance 42.23%

just a quick question. Ive been looking at mobos and i can't decide between the DFI lanparty and the A8N-sli premium. I know they both have some great features but i mainly just want some oppinions from those of you who have or have used either of these. thank you, mobo going to be paired with a x2 4200+, 2 gig xms, 7900 GT, and a 74G raptor if that changes anything.
 

Answer:A8N premiun or DFI Lanparty?

You're not using SLi so don't get an SLi motherboard. Get an Asus A8N-E or a DFI LANPARTY motherboard without SLi. With an X2 and 7900GT, I recommend the Asus A8N-E. If you had an Opteron, I'd go for the DFI. Best of luck!
 

2 more replies
Relevance 42.23%

http://www.pccasegear.com/prod1847.htm

Hey im just wondering if this mtoherboard is a SLi board. It says it comes with a SLi graphics card bridge, what is with that? and is the LANPARTY nF4 SLi-D worth getting over this board
?

Answer:DFI LANPARTY UT Ultra-D ??

no that board is not SLI, it just has 2x pci-e slots

and if you're going to go SLI, then get the SLI board, if not, then don't

IMO, there's no point in going SLI

9 more replies
Relevance 42.23%

A buddy of mine was saying that he's heard the new DFI Lanparty boards could crash if you run it for an extended period of time. They overclock great I am sure, but are they very stable? Or is my friend just full of ****?

Answer:DFI Lanparty - unstable?

your friend is full of ****

i've ran my comp for days without failure

he's probably saying that because some people get ****ty psu or ****ty ram that don't last long

5 more replies
Relevance 42.23%

I'm trying to overclock an AMD64 3200+ on the DFI LanParty UT nF4 SLI-D mobo. I can't figure out how to up the CPU voltage. Anyone know how? I have it clocked to 2.25GHz on 1.376v. It's Genie BIOS and the vcore is not accessible. Is there a multiplier of some sort?
 

Answer:overclock on DFI LanParty UT nF4 SLI-D

it's not a multiplier. the BIOS on the lanparty boards list the VCORE as "VID" (voltage ID)

the setting that says CPU VID control is the standard incremental voltage adjustment. the setting that says CPU VID special control is a percentage based voltage adjustment beyond the incremental adjustement.

I have not used that board, but a quick google search answered that question pretty easily.

good luck
 

9 more replies
Relevance 42.23%

System was stable before I touched anything. I got a good deal on some Adata Vitesta DDR 400 (2x1GB) identical to what was in my system. I added the new memory, so 4x1GB Adata Vitesta DDR 400 is what is has now. XP Pro SP3 started up fine, I restarted and now it will not even post and hangs with 2 diagnostic LED's lit, not recognizing my vga card. I reverted back to just the 2 original sticks and the same thing happens, I even removed 1 stick. I am having the same problem on a DFI RDX-200. Has anyone experienced this before?
 

Answer:DFI LanParty Ultra-D UT

First check that you did not bump a cable loose in your computer, make sure your video card is seated properly, also make sure you are installing the RAM properly. You say you have diagnostic lights, what code is it giving you and do you have your manual to see what it is? If you don't, post what code you are getting and we can google around and see if we can find it.
 

5 more replies
Relevance 42.23%

I will be building my first computer soon, and wanted to use the DFI lanparty ULTRA -D mobo.

A lot of replies on newegg say things like 'not a beginners board!' and 'i had a lot of trouble with ram frequincies' and 'my ram didn't work in dual channel mode'

So im stumped here, could you guys tell me if it's a good board from your expieriences with it? if it's not a beginner board oculd you recommend me one that's better within the same price range?

Thanks!

Answer:DFI lanparty ULTRA-D

The RAM problems are usually fixed with BIOS updates and time, from what I hear.

The not beginners board comes from the insane amount of options in the bios, that most DFI boards, let alone NVidia DFI boards (And Lanparty board) have.

Excellent board from what I've read.

9 more replies
Relevance 42.23%

Well, after I was done reapplying the thermal paste to my chipset, I started the computer up.

"Error loading operating system"

...well f***************************** ****. Any ideas? (I've tried resetting CMOS)

More replies
Relevance 42.23%

I just put together a new comp with a DFI Lanparty UT SLI-DR mobo and a AMD Athlon 64 3500+. once i had the computer mostly put together (e.g. floppy, cd drive, hard drive, ram, processor, PS) and i realized that there is NO WAY TO CONNECT A MONITOR to the board. so, i just slipped in my evga geforce 7800gt and attached my LCD monitor to that, with an adapter. but when I powered up the sysetm all the fans and everything went on, but there was no activity on the monitor. and the cd drive wouldnt open when i pushed the button. and the "diagnostic LEDs" all went on and stayed on, indicating that the system was still at the earliest start up phase and hadnt recognised the prossesor, RAM, or VGA. Help! I cant get my new comp to work

Answer:problem with dfi lanparty sli-dr

i think i have an idea! the aspire 600w powersupply dosent have a 4 pin 12v connector for the motherboard! could that be the problem?

7 more replies
Relevance 42.23%

ok folks, first post here..came here because im in desperate need of help... i recently purchased a DFI lanparty UT NF3 and i hooked it up correct and it started up fine, but as soon as i did ANYTHING in BIOS, the computer would restart as normal, but with a blank screen. I deemed the bored defective and went to exchange it at the Fry's but they didnt have it, so i went to a different Fry's and exchanged it there, took it home, and have the EXACT same problem. does anybody out there know anything about this??? I cant seem to figure it out. it will only work when i reset the jumpers, so i know there has to be something wrong...anybody's help will be greatly appreciated.

Answer:DFI lanparty ut big prob

post all of your hardware. be detailed.

for a start, remove all your non essentials, and try to start it with just the cpu, ram and if you have onboard video, use that instead of a graphics card. if you have multiple sticks of ram, start with 1 stick.

3 more replies
Relevance 42.23%

Ok first off, I have never been very good at networking. But I did mange to get my 2 PC's my kids PC ( all on xp home) and my Xbox all routed through my DI-604. I just built a new Rig, and I cant get it to connect to the internet at all. I tried direct to my modem and through my router. I unplugged my modem and router both to try to let em reset. Some on please point me to a walkthough to get it all set up correctly. My old rig still runs on the router if I want it to. When I check status on new rig, it show no address or anything. Its also on a 1394 connection, on the DFI board. I am way lost please point me somewhere.
 

Answer:Xp Pro and DFI Lanparty and Router??? Please help

you need to install the drivers for your onboard network card


the 1394 connection is for the fire wire ports on your motherboard, i dont know why they show up as network connecticons, but mine do the same thing.

check the dfi website or the cd that came with your motherboard for the onboard network card drivers for your specific motherboard
 

3 more replies
Relevance 42.23%

now that i've fallen for it and i can't find any clear documentation that came with my motherboard that states this i'll say it out loud. DO NOT INSTALL THE USB DRIVERS ON THE CD IF YOUR OS IS NEWER THAN 2K SP4!!!

http://us.dfi.com.tw/Support/mb_faq_...YPE=US&SITE=US

i suppose someone has already pointed this out but i can't believe this didn't warrant adding a note anywhere in the packaging

Answer:DFI LanParty USB drivers

for anyone interested i found a real solution and i'm amazed DFI didn't figure it out . if you make the same mistake as i did your usb will show up as 2 different host controllers. if you expand the two controllers and look at the properties of the top device in each, then have a look at driver details. one will say "windows xp publisher" as driver publisher and the other will say something like "OCW". simply uninstall the one labelled OCW and it should revert to the windows XP driver.

6 more replies
Relevance 42.23%

im recently having issues booting up into window's or even getting to the bios i sent my computer in to be fixed all 4 led light's are red and stable and they can't figure out the problem the only thing they said was that the bios chip might be corrupted im wondering if anyone here know''s anything i can do to fix it and im wondering if i just buy the same motherboard and put the ram and cpu i have in it along with my graphic's card or is it worth bying the motherboard cause they don't know if the ram and cpu are fried with it as well if someone could get back to me asap would be muchly appreciated!

Answer:nf4 lanparty ultra-D

This forum is intended for issues related to systems running Windows 7. I see that you're on XP. (I also see that you like run-on sentences.)

That said, I don't know what to suggest. The Lanparty UT NF4 Ultra-D is a fairly old (2005) Socket 939 board. I think eBay may be where you'd have to go for a replacement motherboard, or a replacement BIOS chip. (Both the board and the chip are listed on eBay.)

If you'd like to try just updating the BIOS, the latest version is 406, from April of 2006:

DFI LANParty:The Best OC Platform! Overclock, Motherboard, Intel, AMD

I suggest using a floppy-based version, as it's safer than flashing from Windows.

Good luck.

1 more replies
Relevance 42.23%

I built a system using a DFI Lanparty board using IDE raid 0, which the board was made for (not ATA), with W2k, SP4. I used 2 160g drives to do this, used good components, lots of memory, etc. It worked fine for quite awhile, until I added an MT 4 sound card for the purpose of in house music recording and editing (I'm also a part time musician). Almost immediately, it started to hang, so I decided to uninstall the card and software. Did that, then when I rebooted the system, at the last stage of the boot process, just when you think everythng is cool, I get a blue screen registry error message. I am no programmer, but I do know a lot of basic recovery methods, and none of them worked. My main question is this- is there bootable software available on CD that I can use to address this registry error issue, or is there another approach? Keep in mind that I can get to a command prompt screen that allows me to see that all the files are still there with a directory command, yet cannot boot in safe mode or any other F8 option, even when I use the W2k CD. I still get the blue screen error message which passes very quickly, something like ...security.ini..., and then the system reboots repeatedly, ad infinitum, like it is in a loop, to the same results every time, until I shut off the power. If you have any input, please let me know at '[email protected]'
 

Answer:DFI Lanparty IDE hangup

jamsum said:

I built a system using a DFI Lanparty board using IDE raid 0, which the board was made for (not ATA), with W2k, SP4. I used 2 160g drives to do this, used good components, lots of memory, etc. It worked fine for quite awhile, until I added an MT 4 sound card for the purpose of in house music recording and editing (I'm also a part time musician). Almost immediately, it started to hang, so I decided to uninstall the card and software. Did that, then when I rebooted the system, at the last stage of the boot process, just when you think everythng is cool, I get a blue screen registry error message. I am no programmer, but I do know a lot of basic recovery methods, and none of them worked. My main question is this- is there bootable software available on CD that I can use to address this registry error issue, or is there another approach? Keep in mind that I can get to a command prompt screen that allows me to see that all the files are still there with a directory command, yet cannot boot in safe mode or any other F8 option, even when I use the W2k CD. I still get the blue screen error message which passes very quickly, something like ...security.ini..., and then the system reboots repeatedly, ad infinitum, like it is in a loop, to the same results every time, until I shut off the power. If you have any input, please let me know at '[email protected]'...
I did receive some helpful replies to this initial post.This is a computer that I cannot con... Read more

1 more replies
Relevance 41.82%

Hey everyone,
ive got a small problem between a choice of two good motherboards.
Choice 1: Asus A8N-SLI Premium
Choice 2: DFI Lanparty SLI-DR

Just to tell a little bit about me, i like to overclock my graphic card, although i dont really know much about overclocking other than that. (i.e. im not much into overclocking)
However, im looking for the best motherboard available, preferably for gaming, and without having to tweak, overclock or change any settings.

Please someone help me! Which one is better?

(my cpu specs are
CPU: AMD X2 4400+
GPU: XFX 7800GTX (490/1300)
RAM: 2GB OCZ dual channel LE (2 x 1024) Platinum edition
Motherboard: Which one is better?!)
 

Answer:which is better (asus a8n-sli premium or dfi lanparty sli-dr?)

Some reviews to help you decide, I have linked to a few as you'll get an overall viewpoint rather than one reviewers opinion.

http://www.pcper.com/article.php?aid=118
http://www.hothardware.com/viewarticle.cfm?articleid=645&cid=3
 

16 more replies
Relevance 41.82%

Forgive me, but I am rather new to building computers. My computer that I use now is out of date, with a bad mobo and processor, but I have a great hard drive and video card. As such, I am replacing my mobo, processor, and upgrading my RAM. However, I have no idea if what I'm planning is compatable.

These are the pages, and yes, I know that a lan party is not a begginer board, but I'm having my brother install it all, but he is unavailable atm.

MOBO: http://www.newegg.com/Product/Product.asp?Item=N82E16813136145#DetailSpecs
RAM: http://www.newegg.com/Product/Product.asp?Item=N82E16820144151
Processor: http://www.newegg.com/Product/Product.asp?Item=N82E16819116183


I realize that this is probably very, shall we say "Noobish", to post, but I don't want to waste my money on things that don't work. Thank you for any and all help.
-Dorjan
 

Answer:DFI Lanparty mobo compatability help

i need to know what exact video card and harddrive you already have. you could probably do yourself a big favor by choosing an amd athlon64 system, as said platform can be had for less expense and has numerous advantages over the p4 5xx series. choosing an upgrade depends largeley on your anticipated uses for the machine - what are they?
 

2 more replies
Relevance 41.82%

Well, I just got finished installing a new Lanparty Ultra D, and the CPU fan is going really slow. Speeds around 950rpm.. Im pretty sure its something with the BIOS becuase before it shows the lanparty logo its spinning what it looks like on my gigabyte board, pretty dang fast.

This is my friends first build, so im trying to help him out with the problem. He finally got it done a few minutes after I left to go home and it wouldnt turn on, and whaddya know, when i get back, it works.

Is This normal, or is there something wrong?

P.S. Temps are around 38C...

Edit: I copied this into word. Thought I was gonna be on my name, but i was on my friends lol...i am not deano who posted this...
 

Answer:New DFI LanParty Ultra D, Low RPMs...

Fixed...Mods please close this...
 

1 more replies
Relevance 41.82%

Just built a new system with the above mobo as a base. Throughout the set up I encountered a couple times when I would plug the power supply back in, turn the power on (on the power supply, which is a seasonic 600w) and then the power LED would start flashing and continue. When this happened the mobo would not power up. I figured I had a loose connection, so I Pulled everything out and started a slow systematic build and checking to see if a particular piece was causing the problem. Including reseting the cmos.

After working my way through everything, it booted up and ran great! So I installed and updated everything, played a little BF2 and everything seemed fine.

The next day I was online for a bit in the am, shutdown for a couple hours and then tried to boot again. This time however, the LED started flashing again and it wasn't booting. Again pulled it all apart and rebuilt, it didn't restart this time though (can't remember if I reset the cmos this time)

I can't seem to find anything in the manual or online that tells me what might be causing this. Any ideas or help would be great. I can give all the specs if anyone needs that.

Thanks
 

Answer:Mobo Unresponsive - DFI Lanparty UT nF4 SLI-DR

Hey there,

Thanks for that suggestion, unfortunately none of those led's are lighting at all (I believe they only lit when I was actually able to turn the power on the board on).

It is the stand-by power led that is flashing. As soon as the power supply is turned on this light starts flashing and nothing else will do anything else. The times the system worked correctly, this led was constantly lit and steady.

thanks
 

6 more replies
Relevance 41.82%

Hi there,

Today my PC has suddenly decided it does not want to turn on. I'm not sure why it doesn't want to do this but yesterday i seemed to have trouble turning it on since my PSU needs to be turned on and if you don't allow long enough for it to get enough power it will get a 5 second burst of power but in order to turn it on i just had to keep turning it on and off at the PSU and keep pressing the on button and eventually it turned on.

Build:

AMD x2 4800+
7900GTX
DFI Lanparty SLi-DR
OCZ 2 x 1 GB DDR2 platinum ram
Hiper-R 580W PSU

Furthermore, the motherboard is getting some power since the diagostic LED is orange and has always been like that when power is on and the PSU is on since the red light is on and the mobo is getting some power.

Since it is a DFI, i used the EZ switch which allows me to try and turn it on with a button but it did nothing.

Just wondering if any of you would have any idea. Had this PC for 3 years - no problems and now suddenly today - it has that. I havn't even added anything to it in months and last time it was just a TV tuner.

Oh yeah i havn't overclocked it or nothing.

Cheers

Edit: Ethernet port doesn't light up like it used too when something is connected to it which is very wierd since impretty sure it did - even if the pc wasn't booted up.

*bump*

Really would like anybodies advie plase.

I tried so far:

* Checking the 12 pin and 4 pin connecton is i properly
* Ensuring no loose wires
* Tried using t... Read more

Answer:DFI Lanparty PC Boot problems

DO NOT Bump your own topics within 24 hours. If it keeps up we will start to close them out. We will be around to help when we can. Bumping your own topic 2 hours after you post it will not get you anywhere.

Have you checked another PSU? Have you checked to make sure that it wasnt the mobo? Have you taken out all un-necessary parts and tested with only the mobo, cpu, ram and hard drive? Have you tried only 1 stick of RAM?

3 more replies
Relevance 41.82%

My problem is that I cannot run my memory in dual channel anymore. It worked for over a year then the computer started giving me trouble so I replaced the RAM, didn't work. Then I finally put it in the first two slots instead of slots 2 and 4 required for dual channel. ( I actually tried every combination and this is the only config. in which the computer would even post). Anyone else have a similar problem or suggestion?? Thanks

More replies
Relevance 41.82%

if you're nice enough, can you please take a look at your karajan audio module and see if there's any jumpers on it?

if so, where are they on and what color are they>?

this is because i'm RMAing my board tomorrow and i won't have to do it if it's a jumper problem, because mines came with no jumpers on the module and i was looking through the mobo's box today and a tiny ziplock bag with 5 13.5mm blue jumpers fell out

Answer:EVeryone with a DFI lanparty ultra-d mobo please help!

8|_|mp

1 more replies
Relevance 41.82%

Yep, apparently with the fan at it's max, 6490 rpm, it's still at 49* celcius on idle.

So, since I just got it, I don't want it to get ruined right away. I've been thinking of protecting my investment and purchasing a new fan. Can any suggest the type of fan I need?

Answer:DFI Lanparty chipset overheating right out of the box...

Mine idles at 39-40 and maxes around 48-49. I would RMA it.

4 more replies
Relevance 41.82%

After much thought and research, I think I have found two good mother boards for my modest new pc build.


AMD Athlon 64 3000+ Winchester
Western Digital Raptor 74GB 10,000RPM SATA
2x512 corsair xms (DDR400 / PC3200)
PNY Verto GeForce 6 6600GT PCI-E 128MB GDDR3
THERMALTAKE 480W XASER SILENT

Ok, so I am torn between the Asus A8N-SLi Deluxe and a DFI LANPART board one of these three (I don't know which of the 3 though :S).

I realised that I have posted about this before, but I'm just unsure between these mobos.

I also appreciate that it must get very boring telling people what to buy for thier PCs, and answering questions all the time, but if you help I'll give you a big kiss

More replies
Relevance 41.82%

Hey guys I need help setting up a 8 man LanParty in my house. I'm thinking about buying 2 of these hubs Click Here! and using my friends dell computer with a 10 base NIC in it to host the game server from. I need help on how to make all the PC's talk to each other I tried reading the guide at lanparty.com and that just confused me. Can someone please help me?

Were gone be playing games like:
CS:S
CS 1.6
CS 1.5
BF2 16 Man
Call of Duty
UT2004
Doom 3
The lanparty is going to be 2 days long.

Thank You!
Alex S.
 

Answer:Setting up an 8 man LanParty (*noob*)

I hate marketing droids.
"Switching Hub "

http://www.encore-usa.com/product.php?id=11&lang=
"The ENH908-NWY is a high-performance Fast Ethernet switch with 8 ports capable of 100Mbps speeds. Auto-negotiation operation (NWay) automatically determines between 10Mbps or 100Mbps when connecting to other networking devices. "

Cool, looks like a decent enough device.

As for the actual setup, it would be a bit easier if you could tell us what guide you are using and at what part you get confused.
 

26 more replies
Relevance 41.82%

I was nearly done putting together my new system when I ran into some trouble. My video card, a Connect3d X800 GTO is too long to be installed on the pcie1 slot because it runs into the chipset fan. My question is can I install the card in the other PCIe slot marked pcie4 without losing performance. The manual said that on the SLI version of this board, in single card mode the pcie4 slot only received X2 bandwidth.

Answer:DFI LanParty UT nF4 Ultra-D trouble!

It goes in the PCI X16 slot. If it hits the chipset fan, remove the decoration from it; you don't need it. Only the heatsink and fan matter.

6 more replies
Relevance 41.82%

lol i could use some help from anyone who has successfully set up a LanParty UT Sli-D NF4 in a TT Soprano case. by successfully i mean attached the top audio and firewire connectors to the mobo. i'm pretty sure i got the firewire right and i've used the usb so that is right. what i'm most confused about is the audio.

Answer:lanparty and soprano case

are you asking just for your board or how to in general?

7 more replies
Relevance 41.82%

Hiya, I posted on here a while ago regarding building my first computer. Well its all built and I'm having trouble with the SoundBlaster 2 ZS I installed.

I beleive the problem to be to do with the fact that the SB card is in the bottom PCI slot, and apparently they are not very stable with this. Basically when playing SOME games the game will crash and the sound will loop itself 0.5 seconds over and over again, until I hit the re-set button. This is a real problem having spent a fortune on my new computer. So I was wondering what people would suggest for me to fix this problem? Either buying a new MotherBoard or buying a new soundcard, and in which case, is this problem sure to go away?

I found this info out at the steam forums:

Quote:




HL/CS/DoD & other Games Crash with Looping Sounds

Problem:

For a while now, say a month or so, I've been having a re-occurring problem, varying in how often it happens. During CS game play, for no reason whatsoever, the game will freeze and I will hear a constant looping sound.

The reason I have posted this now is because the 10+ attempts I've tried to play CS today, every time the game has frozen, and the sounds loops at what just happened on screen. For example - if the game froze in the middle of a firefight, I will hear the last few shots loop over and over again.

I also have to 'power off' my PC every time when it freezes so I can't get an error report.


Possible Solution (thanks to Steal... Read more

Answer:LanParty nF4 SLI-DR + SoundBlaster Problem

download latest the driver for it ,on the website and install it.

1 more replies
Relevance 41.82%

Hey all,
Anyone have this mobo? When I enable the 2nd LAN port (nVidia) my system seems to get problems like freezing and whatnot. Ever since I disabled the second port, things are running smooth as ever.

Anyone figure out a way to enable the LAN port without the problems?
 

Answer:DFI LANPARTY NFII Ultra (rev a)

i dont own your motherboard but mine is similar in design and when i enabled the second lan port after windows has been installed i got serious stability problems - apartently this is an nforce2 chipset thing so its NOT a fault motherboard (we hope) i happens to all us lot with NF2 motherboards.
the only solution (i know of) is to format ur HDD, enable the lan port and reinstall windows - apartently that solves it
hope that helps

Steg
 

2 more replies
Relevance 41.82%

i nave the following setup:
DFI LANPARTY UT nF4 Ultra-D
AMD64 3200+ CPU (Winnie Core)
2Gb Branded PC3200 DDR RAM
200Gb Western Digital 7200rpm Hard Drive
250Db Western Digital 7200rom Hard Drive
Sony 16x DL DVD Writer (Black Facia)
Gigabyte ATI Radeon X800 256Mb PCI-e Video Card (fanless design with heatpipe)
Soundblaster Audigy Soundcard
SkyHawk MSR-4610 Aluminum Case (Brushed Aluminum)
Rosewill 450W Silent PSU
Thermalright XP90 HSF
i am currently trying to install xp, and for some reason the optical drive will not open while being plugged in to the mobo. nor does the motherboard reckognize either of the two harddrives i have installed. im posotive its a driver issue, but if i cant use the optical drives what are my options to do this, do i need to dust off a floppy drive??? let me know if anyone has any advice. (fyi i purchased this obo from a respectable member of this forum who assured me it worked great, and i have no reason to doubt it.)
 

Answer:DFI LANPARTY UT nF4 Ultra-D + xp = trouble for me :(

check your bios to make sure you have enabled booting off those devices

make sure you have not disabled the ide / sata controllers

if you've gotten xp installed, have you loaded the latest drivers?
I have basically same setup...same mobo, proc, 2 GB of ram, 7800gt and everything just fine
 

4 more replies
Relevance 41.82%

just wondering how I get to the bios with my lanparty mb

Answer:How do I enter the bios with the lanparty mb?

should be delete

2 more replies
Relevance 41.82%

Alright, new build is coming along great. Except Problem #1, for some reason I always run into problems but this time it wasn't my fault.

Picked up the DFI LanParty Ultra-D nF4 board 939 and a Aspire 500watt psu. 12v, now the psu has a 20pin my board has a 24 pin.... Uhhh didn't know this until; I got home from the 3 hour away store. And the tard working there told me it would work... Help... Although one way my connector off the psu. Does fit in. And I can power on, I have the 4 pin plugged into alogn with the pin that connects to like HD's and CDROMS theres a port on my board forgot the name, but yes I have that plugged in too...

Help would be appreciated do I need a 24 or am I ok how I am now?

Answer:DFI LanParty Power Connector

please dont create 2 threads about the same thing. check ur other one for the answers

7 more replies
Relevance 41.82%

This will be my first post to this forum, so greetings everybody.

The issues I'm experiencing lead me to believe I am dealing with hardware problems, which is why I'm posting here. I've been dealing with a gamut of issues since putting the PC together, and for all my effort I haven't been able to pin down the cause(s). This is going to end up being a long post in an attempt to give you all as much info as I have. First my build:

MOBO: DFI LanParty UT nF4 SLI-D (bios ver 6.00)
CPU: AMD Athlon 64 Processor 3500+ Socket 939
GPU: BFG GeForce 6800CTOC 2x in SLI mode Driver: 7.8.0.1 (currently)
RAM: Kingston DDR-SDRAM 1024MBytes (2x 512Mb) (Frequency 200.9MHz)
PSU: SilverStone Zeus ST65ZF 650W

Now the issues. This rig was built around May/June, and even back then I would have issues with the computer restarting during gaming sessions. I attributed it to heat, so the side of my case went bye bye and I placed a giant floor fan blowing in it. This seemed to fix the lockups/shutdowns, for the most part, but they would still happen. (Even when the fan /wasn't/ blowing on the rig I only ever noticed either GPU's going any higher then 83 degrees C) So I started to shy away from it really being a heat problem, but keep the fan there in case. Of course, I updated games, updated drivers, updated Bios and all that, and the attempts to fix it never lasted long. With the update of my video drivers to (if I recall correctly) 7.6 I got a nice warning that there was insufficient power... Read more

Answer:BFG 6800GTOC SLI / DFI LanParty nF4 SLI-D Issues

With the 81.85's are you still getting shutdowns/lockups? I had some issues with my SLI setup using 78.01.

There should be a utility that came with your mobo to monitor your voltages, use it to check your 12v rail (while in SLI mode, of course). If it drops significantly below 11.90 when under load then you could be looking at a PSU issue.

4 more replies
Relevance 41.82%

It is always the easy stuff that is difficult. I have a stack of manuals, but no explicit directions for mounting the motherboard to the Case. The board has seated to the case with those mounting screws. (One short). Only two copper screws to secure the board to the case. Doesn’t seem solid and can lift. What are those plastic thumbscrews for? Needless to say, i am a newbee and tolerance with my lack of confidence is greatly appreciated..

More replies
Relevance 41.82%

Ok, so I have been doing some reading throughout multiple sources and only found a few similarities to my issue. RAM test fine during stress tests, (As did mine, 3 passes through full boot MEMTest) but crash while gaming or random restarts just occur. From I reading I concluded that it is possible that the ram setup in the bios my not work for the speed of ram (PC 4200 etc) OR the RAM may be overheating, I have no clue which is more likely, my friend and I put this together, but he is more the hardware guy, I am more of programmer -.- Either way, I get Error 132 Crashes in World of Warcraft, and varios other error that point to RAM. Please anyone, this issue seems to be coming to a conclusion, I have been on sever time consuming 'wild goose chases' so to speak and tweaked several different options/ replaced cabling in the PC, to no avail.

Thanks

Sieg
 

Answer:LanParty UT RDX200 CF-DR RAM issues! Please Help!

9 more replies
Relevance 41.82%

Hello everyone! I was looking at mobos' and i came across the DFI LANPARTY UT nF4 Ultra-D and the MSI K8N Neo4 Platinum mobos. The lanparty mobo seemed more attractive, where as it seems to be more of a "gamers" board. I have never built with these two brands, MSI and DFI, so i was woundering which mobo would be the best for gamers. The lanparty mobo has 2 PCI-express slots, not SLI, and it cost about 10 bucks more. I dont really need the extra pci-e slot, expecially if its not sli. I also have herd many talking about the lanparty board being difficult to install and it being very picky about the memory. As for the MSI board, most of everyone has said it to be a breeze to install. I would rather get the MSI board, which is less expensive, and it being very easly to build with, rather than getting the lanparty board, having it to be more expensive and difficult to install, but yet is basicly the same as the MSI board. Perhaps some help from people who have these boards would be helpfull. Any help will be welcomed. Thanks

MSI board
http://www.newegg.com/Product/Product.asp?Item=N82E16813130484

DFI board
http://www.newegg.com/Product/Product.asp?Item=N82E16813136152
 

Answer:Lanparty or Neo4 Platinum?

I used the MSI K8N Neo4 Platinum motherboard on my first build and found it easy to setup. I don't know anything about the DFI board though.
 

18 more replies
Relevance 41.82%

Question does anybody have Winbond h/w doctor v3.4.1.1 looking to d/l off dfi site but can't find it and out of town on business just formated and installed winxp with sp2 and looking for this application can't find it any help would be great
 

More replies
Relevance 41.82%

http://secure.newegg.com/NewVersion/wishlist/PublicWishDetail.asp?WishListNumber=7334107

(let me know if the link is dead)

I'd love to build this, but I already have more computers than I know what to do with, but this may be a nice template for someone else wanting a good lanparty type system.

Here're the specs.
Xqpack2 micro atx shoebox case
Corsair 520w PSU
Asus P5K-VM G33 MATX (can be oc'ed)
Intel C2D E6320 4M cache
Zalman 7700CU CPU Cooler
EVGA 8800GTS 320MB
G.Skill 4GB DDR2 800 2 x 2GB
WD 750GB SATA 3.0Gbps 16M cache HD
LG 18X SATA DVD-RW
Windows Xp/Vista 64bit(not on list)

It'd be around $1450 with windows and shipping.

Yeah, I'm just bored, so I went "window shopping."
 

Answer:Micro ATX C2D LanParty Gaming PC

Nice build. But it's better to get 4x1GB than 2x2GB... the 1GB sticks are more reliable, overclock better, and you don't lose as much memory if one fails.

Link works
 

2 more replies
Relevance 41.82%

Well, I am building a computer (http://www.techist.com/showthread.php?threadid=59651) and was just looking at my perspective Mobo on Newegg and notced the lack of ports i thought came on all mobos such as the ones pointed to by the arrows. The only ports i saw were the sound, USB, and firewire ports

any help is needed cuz i don't wish to waste $130 on a mobo i cant use!
Thanks

Answer:DFI LANPARTY Mobo Question

THE DFI Lanparty nF4 board does not include the old skool serial and parallel ports, the two near your PS/2 port that have the numerous pins. The other one that is above your intergrated 10/100 LAN is your intergrated video VGA connection. DFI does not have intergrated video and this port will be found on your video card.

I assure you the lanparty does include the required PS/2 ports, and the others you've pointed to you aren't even using anyways and doubt you ever will so it's not really an issue.

DFI I/O ports are:
6 USB 2.0
2 PS/2
2 Intergrated 10/100 LAN
1 Firewire
7.1 Sound

If you really need the missing ports DFI provides a FrontX control panel that has a variety of ports avalible on it.

3 more replies
Relevance 41.82%

Alright so I got my LANPARTY UT nF4 SLI-DR and my power supply has something that it can be monitored by the comp, well does anyone know what one to put it in for the mobo to monitor it? This is what the website says, "Monitors the speed of the CPU fan, Fan 2 and chipset fan" So should I just plug it into Fan 2 slot? In the booklet that came with the mobo it shows me that the CPU fan, chipset fan and Fan 2 all says "sense" and the fan's 4 and 5 say N.C. instead of sense. Anyone know if 2 will sense my power supply fan, its an Enermax EG701AX Noisetaker 600watt. Thanks!

-Ryan

Answer:DFI LanParty Mobo question

This board requres a lot of power, a 4-pin, a normal board power, HDD-type and an FDD-type. I've never seen an FDD type?

-Ryan

3 more replies
Relevance 41.41%

I have the stuff listed in my sig. and I just put it together about an hour ago. I'm not sure which two of the three slots the RAM should be in to be running dual channel. Right now they're in 1 and 2, but I don't think it is running dual channel because the RAM has the activity led's and they're not the same (usually). I couldn't find anything in the manual that came with my mobo as to which to sockets to put the RAM in, if you could please help me I'd really appreciate it, thanks!

Answer:Dual Channel RAM with DFI Lanparty mobo HELP!

Generally with dual channel ram, the two that are dual are the same colour. Also the slots are generally positioned: || |
The two that are FURTHEST from each other generally run in dual channel.

So put them in 1&3. Also make sure that dual channel is enabled in your bios. When you boot up and it goes through POST it should tell you when channel memory you are using. (single or dual)

3 more replies
Relevance 41.41%

I'm basically stuck mid part where the installer is searching for components/drivers, it tells me i can safely remove the win7 installer from the dvd-rom drive and mount the drivers in it, after which i don't know what to do there are drivers appearing on this huge white box and i clicked finish, then it just instantly loop on searching drivers etc. I might get some screen shots later if it is needed..

Answer:Need help installing win7 on a DFI Lanparty DK P45-T2RS plus

Common Installation Problems and Their Solutions

3 more replies
Relevance 41.41%

Get rid of NVIDIA's Network Manager. I've been pulling my hair out for over two weeks trying to get my new PC connected to the internet via router, and I tried everything. I flashed a new BIOS, disabled the NVIDIA and Windows firewalls, fiddled with every setting I could find dealing with network or internet connectivity, and uninstalled and re-installed damn near every driver in my machine. So, just so someone else doesn't overlook the obvious as I did, get rid of the NVIDIA Network Manager. And I had to use DriverCleaner in safe mode to get rid of all of it. Then I reinstalled the NVIDIA mobo drivers without the firewall and network manager. Now, finally, I can connect.
 

More replies
Relevance 41.41%
Relevance 41.41%

I have just built my very first computer and installed windows 7 on it. I have run into a slight problem, the driver setup they sent me isn't compatible with Windows 7. When i put in the CD a setup message tells me, "The main board is not supported with this operating system. The application will be terminated." I have tried running this program in the Windows 7 compatibility mode but none of the Vista or XP options seem to work. To top it all off the DFI website is absolutely horrible. The CD has the chipset, audio, network, RAID, software and utility drivers on it. Where can i find these drivers compatible with Windows 7 64 bit?

Answer:DFI Lanparty GF9400-T2RS Drivers

Your very first build and you went with a DFI? Brave... I like it.

DFI LANParty:The Best OC Platform! Overclock, Motherboard, Intel, AMD

Here are your drivers.

3 more replies
Relevance 41.41%

First things first, im an experianced computer builder so please dont suggest anything as simple as "check for short circuiting" and the like. Okay...

The Problem....
After pressing the power button on my computer (to turn it on. I was rather unamused when the *** at DFI support thought i ment when the computer was already turned on) it powers down 3 seconds later...

What I've attempted
Tried 2 different power supplies, no effect
Tired a different CPU still no effect
Tried different RAM no effect
Tried removing all IDE devices, still no effect
Tried removing all PCI and AGP cards, no effect
Tried resetting the CMOS no effect

Points to note
When CPU is removed the motherboard powers up properly
This is a replacement motherboard from my supplier since my last one failed on me for no reason so its total runtime is nill
There are no signs of physical damage to the motherboard.
There is no error beeping at all

Any ideas that i might try or check for would be great, excluding returning it.

Thanks

Answer:DFI Lanparty NFII Ultra B problem...

Umm, mabye it was DOA? If the mobo is not posting (beeping) then something is seriously wrong.

3 more replies
Relevance 41.41%

ive got a DFI Lan Party KT400a MB and im really confused, i want to get an Athlon 3200+ but im not sure if it will work, the box says FSB333 (Max. 400) and it takes DDR400 ram, some website say it will take a 3200+ (ie OCUK) but when i emailed to ask they said it didnt. any ideas on this?
 

Answer:DFI Lanparty KT400, Athlon 3200+???

9 more replies
Relevance 41.41%

My DFI NF4 Lanparty Ultra-D is not listed in supported mobos for configuring MBM 5. I have version 5.3.7 mbm which I believe is the latest version, and it even did its own little auto update, but my board is still not listed. What to do? Can I get it to work or do I need a different monitor?

Answer:How to get Motherboard Monitor 5 to work w/ DFI nF4 Lanparty?

Last time i checked MBM didnt have my mobo on it either. I would suggest trying s different moniter.

2 more replies
Relevance 41.41%

I recently installed the dfi lanparty ut nf3 250 gb (all other components are new). I attempted to test the reset button by reseting the system (from the desktop). After pressing the reset button on my case for a second or two then releasing it, the system appears to reset - for example, the monitor resets, the hard drive resets (makes that noise you hear during a cold start) but following the hard drive reset, nothing happens. There is no system beep you commonly hear during a cold start. The monitor is black and the hard drive continues to make that reset sound. Its almost as if the motherboard doesn't reset.

I checked the reset plug that attaches from the case to the mobo and it appears to be attached firmly. Everything else works fine but this.

Can you help?

System specs:
amd athlon 64 2800+
1 gig corsair pc3200 ram
western digital 7200 hd
Coolermaster Centurion Case
Geforce fx 5900SE
 

Answer:Reset function on dfi lanparty not working

8 more replies
Relevance 41.41%

DFI LANParty Hosting Global OC Contest
LANParty, the most famous main board brand worldwide, will hold the first session of global online overclocking competition during April to May of 2009. In addition to a handsome sum of money as prize and awards to the top three, the top ten candidates will also be honored as ?LANParty certified overclocker?.
You can go directly to the Project Europa contest site here. Good luck!

More replies
Relevance 41.41%

Well, I just got finished installing a new Lanparty Ultra D, and the CPU fan is going really slow. Speeds around 950rpm.. Im pretty sure its something with the BIOS becuase before it shows the lanparty logo its spinning what it looks like on my gigabyte board, pretty dang fast.

This is my friends first build, so im trying to help him out with the problem. He finally got it done a few minutes after I left to go home and it wouldnt turn on, and whaddya know, when i get back, it works.

Is This normal, or is there something wrong?

P.S. Temps are around 38C...

Edit: I copied this into word. Thought I was gonna be on my name, but i was on my friends lol...i am not deano who posted this...
 

Answer:New DFI LanParty Ultra D mobo, Low RPMs...

temps around 38 seem acceptable to me...

if you think its a problem with the bios, ensure that the latest bios drivers are installed
 

1 more replies
Relevance 41.41%

Just wondering, will a DFI LANPARTY nF4 SLI-DR Socket 939 NVIDIA nForce4 SLI ATX AMD Motherboard - Retail fit two Leadtek PX6800GT TDH Geforce 6800GT 256MB 256-bit GDDR3 PCI-Express x16 Video Card - Retail?

Answer:Will a DFI LANPARTY nF4 SLI-DR Mobo fit two leadtek 6800 gt's

yes, but i recomend waiting until the next-generation cards come out before you spend almost $800 on 2 video cards that won't be that great a few months from now.

2 more replies
Relevance 41.41%

MSI K8N Neo4 Platinum vs Lanparty UT nF4 Ultra-D

which one?
 

Answer:MSI K8N Neo4 Platinum vs Lanparty UT nF4 Ultra-D

I think I would go with this one becuse of the overclock features Lanparty UT nF4 Ultra-D DFi are really well made boards that get overlooked becuse of MSI and Asus...
 

5 more replies
Relevance 41.41%

OK. I just got an opinion dis-favoring the A8N-SLI board in leu of the equivalent Lanparty. I want to buy the best (yes I dig the board without owning it) but I have read countless reviews and found the Asus to come out on top. Please indulge me in your experience.

Answer:Asus versus Lanparty Boards

I dont know about the A8N. but i've heard its very good.. its the board my friend chose over anything else for his SLi setup...

however, my Asus experience hasn't been great. I burnt my 478 p4p800e deluxe from oveclocking but got it replaced so its all good.. But, its got some great features on it.

DFi are known for their overclockability and overall performance, although I'd say the Asus would be more reliable assuming you wont be overclockin ur FSB.

If it was me, I would go with the DFI completely out of word of mouth/reputation. but just go with whatever ur budget alows

2 more replies
Relevance 41.41%

Hi my Pc been working ok for last 2 weeks done nothing different closed it down last night ,wont start up now just dfi lanparty logo on screen,
Wont even let me go into bios on start up
spec as follows
DFI lanparty NF4 sli-dr
1024mb mushkin pc4400 memory
1x 74gb Raptor 10,000 rpm seriel ata
2x 250gb hitachi 7200 rpm 8mb seriel ata
1x 400gb hitachi 7200 rpm 8mb seriel ata
2x gigabyte 6600gt nvidia pci express graphics cards
any one got any ideas please

Answer:Pc wont start just dfi lanparty logo

Try clearing cmos.


Do you get any beeps?

8 more replies
Relevance 41.41%

well i've heard good things about them; from what i've heard

creative zs2 value<karajan<creative zs2

is this true? is anyone using it right now and can you tell me how good the quality is? thx.

btw, my mobo's sound didn't work so i had to RMA it to monarch and wait god knows how many weeks

More replies
Relevance 41.41%

The setup.

MSI | NX6600GT
2 x 80GB|HITC SATA 8MB
CPU AMD 64 |3200+ ATHLON 939P 90 R
MB DFI|NF4 LANPARTY UT nF4 Ultra-D

DDR CRSR 512MB X2 KIT|VS1GBKIT400
Specification
Manufacturer: Corsair
Model: VS1GBKIT400
Speed: DDR400(PC3200)
Type: 184 Pin DDR SDRAM
Error Checking: Non-ECC
Registered/Unbuffered: Unbuffered
Cas Latency: 2.5
Support Voltage: 2.5V
Bandwidth: 3.2GB/s
Organization: two 64M x 64 -Bit

The Problem.

It's running in single mode and not dual mode.
It tells me the following on boot.


WARNING
The system is running in Single Channel Mode when you plug DIMM module in DIMM 1.
Please install 2 RAM modules into DIMM 2&4 for dual channel operation.


Now I took the ram out of slots 1 & 2 then put it in 2 & 4 but the system will not boot it just continously beeps very loudly. I searched on the forums and didn't really see anything pointing to my problem DIRECTLY so I'm posting a new thread. There FAQ on there webpage has nothing about it except to move a jumper on the board from set 1&2 to 2&3 to be able to up the voltage for massive overclocking (up to 4v's on the ram) and this isn't something I'm trying to do. I'm simply trying to run the system with Dual Memory and not Single Channel mode.




Can someone please tell me what's my problem or how to resolve this issue? The manual only has about 1 page on my issue and again it refers to simply upping the voltage and not this problem specifically.

Answer:LanParty UT nF4 Ultra-D --- Memory Problems!

same thing happened to me:

1.) is this value ram? don't use value ram with the dfi board because value ram sux0rs and the dfi board hates sux0r rams
2.) you have faulty ram (i've gone through 4 kingston value ram to find out that they have crappy faulty ram)

9 more replies
Relevance 40.59%

Hi can you help plz, i have been using my nvidia nforce controller for 2 years without a problem and had saved the driver install files.
I reformatted my pc recently but cant get back using my nvidia nic unless i use my NTLworld ambit modem via its usb connection.
I uninstalled all Nvidia drivers and reinstalled nforce driver(NF4w2k666E) selecting "NO" when asked whether i want to install nvidia firewall as i had major problems with this before. i selected to install SWE drivers aswell, I tried changing duplex from autu to 100 half & 100 full duplex and disabled the power option to switch it off to save resources but still nothing. I get limited or no activity. i did get cable unplugged with other drivers.
Do i need xp sp2 installed first?

here is paste from CMD ipconfig /all

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

C:\Documents and Settings\Stuio>ipconfig /all

Windows IP Configuration

Host Name . . . . . . . . . . . . : stu
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection 6:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : NVIDIA nForce Networking Controller
#3
Physical Address. . . . . . . . . : 00-00-00-00-00-00
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfigurat... Read more

Answer:Nvidia Nforce driver dfi lanparty Nf4 cant connect plz help

Ok been playing with settings and forced mac address in bios using mac address i got from using my usb connection, it says connected but cant ping anything or access websites using firefox or IE, and now get this in ipconfig /all
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

C:\Documents and Settings\Stuio>ipconfig /all

Windows IP Configuration

Host Name . . . . . . . . . . . . : stu
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection 8:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : NVIDIA nForce Networking Controller
#3
Physical Address. . . . . . . . . : 00-02-8A-63-E2-B3
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 81.99.186.214
Subnet Mask . . . . . . . . . . . : 255.255.252.0
Default Gateway . . . . . . . . . : 81.99.184.1
DHCP Server . . . . . . . . . . . : 62.252.64.20
DNS Servers . . . . . . . . . . . : 194.168.4.100
194.168.8.100
NetBIOS over Tcpip. . . . . . . . : Disabled
Lease Obtained. . . . . . . . . . : 19 September 2007 20:32:50
Lease Expires . . . . . . . . . . : 26 September 2007 20:23:46

C:\Documents and Settings\Stuio>ping www.google.com
Ping request could not find host www.google.com. Please check the name and try again.
 

2 more replies
Relevance 40.59%

Hey guys,

I was updating the bios of my motherboard when I got a BSOD. Of course now when I turn it on nothing happens. Is there a way to re-flash the bios now? Thanks.
 

Answer:BSOD while flashing BIOS - DFI Lanparty UT CFX3200-DR

Did you keep a backup of the old Bios.
 

10 more replies
Relevance 40.59%

I just installed a new Lanparty nF4 sli-d motherboard, amd64 3200, new 550w psu, and am trying to reinstall windows xp on the hd. Its booting from the CD but when it gets to the part where it says waiting to instal windows or w/e, it goes to a blue screen that says UNMOUNTABLE_BOOT_DISK with a bunch of other jargon. Anyone have this problem and know the solution?
 

Answer:new Lanparty nf4 sli-d and amb64, tryin to install windows

How many HDD do you have? If you have more than one, make sure that the one you are installing windows on is the MASTER disc and the other one(s) are SLAVE discs. You'll have to add/remove jumpers to make one the MASTER disc.

Thats about all I can help you with. I hope it helps.

*DON"T QUOTE ME ON THIS*
 

2 more replies
Relevance 40.59%

I'm going to visit a friend in Germany soon, and we're going to arrange a small LAN party. However, he has a Webstar DPX2203, and neither of us know if we need a router or a switch to be able to be connected tot the web at the same time. It would be GREAT if someone would help a poor network noobie with this!
 

Answer:LANParty with a Webstar DPX2203 - do I need a router or a switch?

From the looks at the crappy manual, I don't believe that modem does any routing, so it definitely wouldn't be able to NAT.

Unless you have a L3 switch with NAT capabilities, you'll need a router in order for multiple machines to access the Internet, unless you're given multiple static addresses by the ISP (doubtful).

Although I highly recommend against it, you could also make one of the systems serve Windows ICS, if it had 2 NICs. You'd plug the one NIC into the webstar modem and the other NIC into your switch, and then give the other hosts the default gateway of the Windows ICS box.
 

4 more replies
Relevance 40.59%

I just got a my new Fx 57 and Dfi lanparty ultra-d setup but it seems that my internet speed from roadrunner is not as fast as before judging by bandwidth tests and my ping in games.

Im using the onboard lan and I have not made any changes what so ever with my internet so I had hoped that it would stay the same.

Are there any tweaks or adjustments I can do in bios or in windows to boost my internet connection? Any help would be greatly appreciated.
 

Answer:Bad internet connection after installing new Lanparty Ultra-d

If you are connected directly to the cable modem, you could try manually setting the port speed and duplex to 10/half. I've seen some NICs that have problems auto-detecting this.
 

7 more replies
Relevance 40.59%

I've got this legendary socket 939 motherboard DFI LP UT SLI-DR Expert chipset nForce4 SLI almost new only one SATA port is somewhat messed up missing those plastic parts from both sides , bought this baby really cheap ~ 55 $ from well known Romanian e-bay like site okazii.ro , and I put it on my FX-60 dual core ( yeah,THAT one! ) and some KINGSTON value memory and tried to boot my rig.Here is my problem now:this board is working those 4 red diagnostic LEDS start 4,3,2 next only one left so no "4 LEDs of death" syndrome for me and the onboard speaker beeps ONCE which I know is always a good thing but I cannot enter BIOS to setup as I need Del key on my PS2 keyboard is NOT working as it should I press the key and the result is 0 nada nothing , first I see the boot logo from DFI after that I see this error message "CMOS checksum error - defaults loaded , press F1 to continue or Del to enter setup" and when I press Del I get nothig and when I press F1 key sometimes I see this message "Verifying Pool Data and Backup CMOS OK!" and other times I see "Sil3114 SATA RAID Press Ctrl-S or F4 to enter RAID utility".One more thing to add is that I can actually use boot menu selection using Esc key to selct HDD,CD-ROM or some other option and this board actually can boot using CD/DVD I already tried UBCD rescue CD and some Linux live distros to see if it's not a problem with my FX-60 processor and I'm happy that it is working well i... Read more

More replies
Relevance 40.59%

So every time I try and use the net while the firewall is on nothing loads (webpages, email, etc) , as soon as I turn it off everything is fine.I'm using the NVIDA firewall that comes with the Lanparty board, anybody know whats going on? I've tried it on a bunch of settings, low, medium, and high, and no luck.

Thanks

-Foz
 

Answer:Firewall wont work with DFI Lanparty Ultra-D

Portsie smortz. Check em out.
 

4 more replies
Relevance 40.18%

Ok, i have a pretty stock...well the spex r in my siggy, but i was thinking of swapping my stock mobo with this one. I'm very $$ conscious, and this is the cheapest UV mobo i found and it seems pretty good (SATA, USB 2.0). Does anyone have it and can post comments/opinions? Any other suggestions. As always, UV reactive is better than not, but if not having it makes a significant difference in $$ or quality, that'd be fine.

Answer:Thinking of switching MOBOs, DFI Lanparty NFII Ultra B

I have it. it is not the fastest mobo (it is slow, except for long term projects)

however the computer that I have it on (with an amd 2800) has never lock up, crashed or anything goofy like that and it has stayed on 24hr a day for the past 2 years

9 more replies
Relevance 40.18%

http://www.fedex.com/cgi-bin/trackin...s=693727974110

i ordered it from monarch (where many people have gotten problems from)

what do you guys think it'll be?

- DOA (dead on arrival)
- messed up (i.e. bent pins, broken switches)
- perfectly fine

i'm putting my money on it being messed up

i hope i don't have to RMA it

Answer:DFI lanparty ut ultra-d mobo coming tomorrow-what condition do you think it'll be in?

i have no idea. But you hope it comes good.

3 more replies
Relevance 39.77%

Here is the situation.
I run a monthly lan and we will have a 5mbit internet connection starting next month. Now I want to firewall off everything(P2P, Messenger, etc). The only internet activity I want people to be able to do is basic web browsing and to update their Steam clients.

I also want people to be required to register to get on the net(At registration they select which tournaments they want to participate in). I was thinking take some of the hotspot software(already does registration and mac address tracking) and modifying it for my purposes. My Linux knowledge is very limited, so the less dirty work the better. The router machine would also be a fileserver and a internal webserver for the Lan.

Recap -
need a solution that does:
-Filtering of all non-HTTP/Steam traffic(for updates, not playing online), other port ranges openable on demand.
-Requires completed registration to access internet, optional: saves info for future Lans.
-Preferred: On first browser opening, no matter what page is requested, sends them to internal lan webserver, all subsequent clicks are normal.
-Acts as internal lan webserver(Running something like ALP) with basic forums(username based on earlier registration)
-Acts as SMB fileserver


Suggestions?
 

Answer:Internet routing solution for LanParty (Registration, MAC, Port Filters, etc)

Very, very interested to see what responses are given, I need a box for the same purpose...
 

21 more replies
Relevance 39.77%

I'm getting the problem where my ITE Smartguardian fan speed settings are not being applied in Vista with the Vista x86 version of that program. This program is right here. I'm not exactly sure how I should automate my fan settings so that when I turn on my computer, they adjust to the proper speed every time. I know Speedfan does not do this in the background and requires you to play around with it every time on reboot, or minimize the window, or whatever, but I'm looking for something more transparent.

Thanks.
 

Answer:Vista ignoring fan speed settings for fans on DFI Lanparty nf4 motherboard

Run it as an administrator.
 

4 more replies
Relevance 39.77%

I tried MBM 5 but it didnt have my mother board listed. Is there another one out there I can use?

Answer:whats a good temp monitoring program for the DFI lanparty n4 ultra?

This is my personal favorite:

http://www.lavalys.com/products/over...ng=en&pageid=1

1 more replies
Relevance 38.95%
Answer:Update OCZ ModStream OCZ52012U ATX 520W Power Supply fit a DFI LANPARTY UT nF4 Ultra-D Socket 939 N

perhaps you could spend a few more seconds typing and formulate an accurate question....

After one simple google search, i found that this power supply fits both 20 pin and 24 pin motherboard power connections. So the answer to your question is yes. It will fit the DFI board...

2 more replies
Relevance 38.54%

I wanto buy a samsung evo 850 ssd which is expensive for my budget but i think itll be worth it...
I need advice as i dont know if i need the 500gb as opposed to the 250gb.
Ill only be having my os and a maybe 2 games (overwatch and league of legends) and ill only be watching youtube and movies and doing homework via microsoft office. Will 250gb run out easy if i get it?
Thnks in advance.

More replies